Table of Contents
Advertisement
Quick Links
SpeedDome
Ultra VI
®
Camera Domes
Installation and Service Guide
RAS816LS and RAS816WLS Series
Figure 1. SpeedDome Ultra camera dome
Mounting
Base
Housing
Eyeball
© 2005 Sensormatic Electronics Corp.
INSTALLATION AND SERVICE GUIDE
Contents
About this Guide ....................................................1
About the Camera Dome .......................................2
Data Cable Requirements .....................................8
Power-Up Routine..................................................9
Synchronizing Domes............................................9
Diagnostic LEDs ....................................................9
Warnings and Cautions .......................................10
Indoor Installation.................................................11
Using the Install/Removal Tool ............................18
Troubleshooting Indoor Domes ...........................20
Illustrated Parts List .............................................30
Specifications-Indoor Dome.................................32
Specifications-Outdoor Housing ..........................33
Specifications-23X Camera .................................33
Declarations .........................................................34
About this Guide
This guide explains how to connect the camera
dome to a mounting base and how to service it.
It does not explain how to:
• Determine a mounting location for the camera
dome. The mounting location is determined by
customer requirements; therefore, this
information is provided separately.
• Attach the mounting base. There are two types
of mounting bases. See information shipped
with the base.
• Assemble housings and structures used with
this dome. See information shipped with the
housing and structure.
• Program the dome. See operator's guide
shipped with the dome.
Page 1
Advertisement
Table of Contents
Troubleshooting
Related Manuals for American Dynamics SpeedDome Ultra VI
Summary of Contents for American Dynamics SpeedDome Ultra VI
-
Page 1: Table Of Contents
Figure 1. SpeedDome Ultra camera dome Mounting Base Housing Eyeball © 2005 Sensormatic Electronics Corp. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Contents About this Guide ...1 About the Camera Dome ...2 Data Cable Requirements ...8 Install/Removal Tool for Base with I/O Board...8 Power-Up Routine...9... -
Page 2: About The Camera Dome
About the Camera Dome The SpeedDome Ultra VI camera dome (Figure 1) comes in black or white finish (to blend into surrounding areas), mounts indoors or outdoors, and can communicate with the video controller over a SensorNet 485, RS-422, or Manchester network. - Page 3 Figure 2. Mounting base and housing and eyeball assembly Standard Base Base with I/O Board SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Indoor Ceiling Mounting Using hardware shipped with the base, the dome attaches directly to indoor ceilings made of sheet rock, wood, metal, or concrete (Figure 3), or to tile ceiling T-bars where they intersect (Figure 4).
-
Page 4: Ruclr (Clear)
Attaches dome to a standard 4 x 4 duplex electrical box. CAUTION: Do not use the same electrical box used for line voltage mains. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Structural I-Beams RHIUIB† I-beam mount Enables dome to suspend from an I- beam. -
Page 5: Ruslv (Silver)
Figure 5. Indoor mounting structures (optional) RHIUFB RHIUAB RHIUIB RHIUPNDT RHIU3X3 RHIU4X4 SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE RHIUHC RHPLA RHIUTH RHIUTR RUCLR RUSLV RUSMK RUGLD of 34 RHIU2X2 RHIU2X2P RHIUWM RHIUCM RHIULWM 8000-2830-03, REV. C... - Page 6 Note: Do not use the I/O board (designed for indoor use) in place of the environmental board. Figure 6. RHODUL outdoor housing (optional) SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE SpeedDome Housing Adapter Bracket (Optional)
- Page 7 Figure 8. Outdoor mounting structures (optional) RHOTR over roof mount (shown with RHOTRF bracket) PHOPN pendant mount SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE RHOWPA pole mount RHOSW/RHOLW wall mount RHOSW RHOWCA corner bracket (shown with RHOLW mount) of 34 RHOLW 8000-2830-03, REV.
-
Page 8: Data Cable Requirements
(called "other air space" in the National Electrical Code). Order cable directly from Belden by calling 1-800-235-3361. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Install/Removal Tool for Base with I/O Board... -
Page 9: Power-Up Routine
4. Lens tilts up 90° (home position). Once the lens is in its home position, you can then use the controller to call up the camera and control it. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Synchronizing Domes To prevent picture rolling when switching from camera to camera, all domes can be synchronized to a 50Hz or 60Hz ac source. -
Page 10: Warnings And Cautions
This installation should be made by a qualified service person and should conform to all local codes. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE WARNING! EU power requirements: This product runs on 24Vac. In the EU, it is intended to be powered from a Limited Power Source. -
Page 11: Indoor Installation
PC boards. − Once disassembled, parts of housing and eyeball assembly are "extremely fragile" and may break. Proceed using extreme care! SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Indoor Installation This section explains how to connect the housing and eyeball assembly to a: •... - Page 12 For address 166, set SW3 to 1, SW2 to 6, and SW1 to 6. Figure 10. Setting address switches SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 2. Attach safety lanyard to cap on housing and eyeball assembly (Figure 11). Use M3 x 6 screw supplied with lanyard.
- Page 13 Micro Termination Coax Jumper JW1 Cable SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 5. Connect the 9-pin plug (data and power) to the 9-pin receptacle (Figure 13). CAUTION: DO NOT connect 9-pin plug unless you have performed step 3 first! a.
- Page 14 9-pin plug LEDs CR2, CR3, and CR4 visible through opening. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 7. Check LEDs to verify that power and data are reaching dome (Figure 13). LEDs CR2, CR3, and CR4 surround video connection and are visible through opening.
- Page 15 1. Set data communications jumper JW1. If data lines continue to another dome, set JW1 across pins 1-2 (unterminated). Otherwise, set JW1 across pins 2-3 (terminated). SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 2. Connect video cable to BNC connector P8 on I/O board.
- Page 16 Output P2 (40mA sync. max.) — Output P3 (40mA sync. max.) — Ground — Ground SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 5. Connect alarm input cable, if used, to P4 connector. 6. Connect power to P7 connector. Pin 1 7. Reattach I/O board.
- Page 17 For address 166, set SW3 to 1, SW2 to 6, and SW1 to 6. Figure 17. Setting address switches SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 11. Connect the housing and eyeball assembly to the base (Figure 18) by aligning the Cap and Base tabs and then turning clockwise until you hear a click.
-
Page 18: Using The Install/Removal Tool
Lifting pole up at an angle, use one of the hooks on tool to catch one of the notches at side of dome and pull down. T-lanyard will prevent skirt or bubble from falling. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE TO CONNECT DOME: 1. Insert dome "eyeball down" into tool's receptacle. - Page 19 Skirt or Bubble Attachment/Detachment Snap tool into pole. Attachment Dome Connection (reverse steps to disconnect) Do not use this tool to connect the standard base! SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Catch notch and pull down. Detachment Line up...
-
Page 20: Troubleshooting Indoor Domes
CAUTION: Once disassembled, parts of the housing and eyeball assembly are "extremely fragile" and may break. Proceed using extreme care! SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Items You Will Need You should have on hand the following items: Phillips-head screwdriver Small slotted screwdriver 2.5mm (0.1") slotted screwdriver (for wire... - Page 21 GSC. See "IMPORTANT!" on page 20 for phone numbers. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE 4. Isolate problem to housing and eyeball assembly or base by attaching dome to another base with I/O board.
- Page 22 I/O board or ship dome and base to GSC. Figure 21. I/O board switch and LED locations RS422 Test Pushbutton Comm. LED Power LED SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE P1 connector (Manchester data) Color Black White P1 connector (RS-422 data) Color...
-
Page 23: Detailed Troubleshooting
Wider blade widths can damage connectors. • Dome contains electrostatic-sensitive PC boards. Use a ground strap when handling boards. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Procedure 1. Match symptom to one of the following criteria: − Dome functions but does not pan −... -
Page 24: Disassembling The Dome
(Page 33). To order parts, see page 34. Tools Required • Phillips-head screwdriver. • Small slotted screwdriver. SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Removing the CPU Board CAUTION: Electrostatic-sensitive device. Use a ground strap when handling CPU board. - Page 25 Remove three standoffs, then remove power supply board from housing. 5. Reverse steps to reassemble. Figure 23. Removing the P/S board SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Removing the Pan Motor Referring to Figure 24. 1. Perform procedure "Removing the CPU Board"...
- Page 26 4. Gently swivel eyeball to totally expose remaining slot cover. With other cover removed, this cover can be easily removed. Figure 25. Removing slot covers SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Removing the Camera 1. Perform procedure "Removing the Slot Covers"...
- Page 27 While pressing tabs, push up on eyeball to detach it. Figure 28. Loosening the eyeball 4. Detach slip ring connector (Figure 29). Figure 29. Detaching the eyeball SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Removing the Camera/Lens Board 1. Perform procedure "Removing the Slot Covers"...
- Page 28 Figure 32. Removing the camera/lens board Prongs (3) DO NOT unplug cable from J1. Camera/Lens Board Bearing Assembly SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Removing the Tilt Motor 1. Perform procedure "Removing the Slot Covers" (page 29). 2. Perform procedure "Removing the Camera"...
- Page 29 CAUTION: When installing a new motor, be careful to properly mesh motor and tilt gears! Failure to do so can destroy both motor and tilt gear. Verify tilt gear turns freely! SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Updating/Reprogramming Dome Software...
-
Page 30: Illustrated Parts List
Tilt Motor 3501-0018-01 Slot Cover (No Lens)* 0500-8037-01/-02 Yoke, Camera 0500-7258-01 Camera/Lens PC Board 0301-0953-01 SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Bearing Assy., Lens Carriage Yoke Bracket (Qty. 2) Cable Assy., Tilt Camera, 23x, NTSC Camera, 23x, PAL Washer, Flat Screw, 1/4-20 x 3/8 Screws, M2x3 (Qty. - Page 31 -03 Color NTSC camera (WHT) Eyeball Assy. (0400-1401-xx) -01 Color NTSC camera (BLK) -02 Color PAL camera (BLK) -03 Color NTSC camera (WHT) SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Base Assembly Assembly* with I/O Board** 6 7 8 34-35...
-
Page 32: Specifications-Indoor Dome
Data Storage ...128 Kbytes of SRAM Menu Languages ...English, French, German, Spanish, Italian, and Portuguese * Using AD2083-02A SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Electrical Input Voltage ...24-30Vac, 50/60 Hz Design Tolerance ...16-36Vac, 50/60 Hz Power Consumption...16W max. -
Page 33: Specifications-Outdoor Housing
Height ...32.1 cm (12.6") Diameter ...24.4 cm (9.6") Weight: Housing (alone) ...2.6 kg (5.7 lbs) Housing (with dome) ...3.8 kg (8.4 lbs) SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Specifications-23X Camera Type ... Interline transfer Scanning Area... 3.2 (H) x 2.4 (V) mm Scanning System ... -
Page 34: Declarations
Example: Wide angle view with lens at 6mm and viewed object at 10m. 3.2mm x 10m = 5.33m Horizontal view (m) 2.4mm x 10m = 4m Vertical view (m) SPEEDDOME ULTRA VI INSTALLATION AND SERVICE GUIDE Declarations Regulatory Compliance Emissions... 47 CFR, Part 15, Immunity ... EN50130-4 Safety...