Sentry W9150 Series Installation, Operation & Maintenance Manual

Original Instructions
Installation, Operation & Maintenance Manual
Waters Equipment W9150/W9250 Series
Sample Coolers
W-SW-IOM-00044-1 8-16
sentry-equip.com
966 Blue Ribbon Circle North, Oconomowoc, WI 53066 U.S.A. | +1-262-567-7256 | support@sentry-equip.com
Standard Warranty
Sentry Equipment Corp ("Seller") warrants products manufactured by it and
supplied hereunder ("Products") to be free from defects in workmanship and, to
the extent materials are selected by Seller, to be free from defects in materials, in
each case for a period as defi ned in the table below:
Brand Product Line
Sentry® ƒ Steam & Water Sampling Products and Systems
ƒ Solid & Powder Sampling Products and Systems
ƒ Gas Sampling Products and Systems
ƒ Liquid & Slurry Sampling Products and Systems
ƒ Pipeline Integrity Products
Waters Steam & Water Sampling Products and Systems
Equipment
To view the full warranty, go to www.sentry-equip.com/warranty.
Do not install, maintain, or operate this equipment without reading,
understanding, and following the appropriate Sentry Equipment Corp
instructions. Otherwise, injury, damage, or both may result.
Copyright
© 2016 by Sentry Equipment Corp. All rights reserved. All product and company
names are property of their respective owners. This document contains
proprietary information. No part of this document may be photocopied or
reproduced without the prior written consent of Sentry Equipment Corp.
Limit of Liability
Sentry Equipment Corp, its employees, agents, and the authors and contributors
to this document specifi cally disclaim all liabilities and warranties, express or
implied (including warranties of merchantability and fi tness for a particular
purpose), for the accuracy, currency, completeness, and/or reliability of the
information contained herein and/or for the fi tness for any particular use and/or
for the performance of any material and/or equipment selected in whole or part
with the user of/or in reliance upon information contained herein. Selection of
materials and/or equipment is at the sole risk of the user of this publication.
Note
The information contained in this document is subject to change without notice.
Safety Information
Please read the entire manual before attempting to unpack, set up, or operate this
product. Pay careful attention to all Warnings, Cautions, and Notes. Failure to do so
could result in serious personal injury and/or equipment damage.
Use of Hazard Information
If multiple hazards exist, the signal word corresponding to the greatest hazard
shall be used.
Defi nitions
DANGER indicates a hazardous situation
which, if not avoided, will result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in
minor or moderate injury.
 NOTE
Information that requires special emphasis.
 TIP
Alternate techniques or clarifying information.
SHALL: This word is understood to be mandatory.
SHOULD: This word is understood to be advisory.
General Safety Precautions
Product Selection, Installation, and Use
Improper selection, installation, or use can cause personal injury or property damage.
It is solely the responsibility of users, through their own analysis and testing, to select
products suitable for their specifi c application requirements, ensure they are properly
maintained, and limit their use to their intended purpose.
Follow proper local, state, and federal regulations for proper installation and operational
requirements.
Always use caution and common sense when working with any chemical. Read
the product label and Material Safety Data Sheets (MSDS) carefully and follow the
instructions exactly.
Warranty Period
Eighteen months from
Potential Equipment Hazards
date of shipment or
twelve months from
startup (whichever
Hot surfaces! This equipment may have very hot
occurs fi rst)
surfaces. If an operator contacts a hot surface, injury
Twelve months from
may occur. Use protective clothing to prevent injury.
date of shipment
If other equipment comes in contact with a hot
surface, damage to the equipment may occur. Ensure
the area around this equipment is kept clear to
prevent this damage from occurring.
High pressures! This equipment may contain fl uids
at very high pressures. Prior to installing, removing,
or maintaining this equipment, ensure that the
equipment is isolated from all connecting piping, the
equipment is depressurized, the contents have been
drained, and the equipment is cool.
Freezing Temperatures! This equipment may have
very cold surfaces. If an operator contacts a cold
surface, injury may occur. Use protective clothing to
prevent injury. If other equipment comes in contact
with a cold surface, damage to the equipment may
occur. Ensure the area around this equipment is kept
clear to prevent this damage from occurring.
WARNING indicates a hazardous
situation which, if not avoided, could
result in death or serious injury.
NOTICE is used to address practices not
related to personal injury.
Freezing of fl uids in tube
can lead to rupture of the
tube wall and coil failures.
Take precautions to avoid
freezing, such as draining
the equipment when out
of service or installing the
equipment in an environment
protected from temperatures
below the freezing point of
the fl uids used.