Specifications - Alpine CDM-9821 Owner's Manual

Indication for CD
– – – H
• Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature
returns to within operation range.
– – – E
• Mechanism error.
1. Press the c button and eject the CD.
If not ejecting, consult your Alpine dealer.
2. When the error indication remains after ejecting,
press the c button again.
If the error indication still does not turn off after
pressing the c button for a few times, consult your
Alpine dealer.
Note
When the "- - - E" is displayed:
In case that the disc cannot be ejected by pressing the c
button, press the RESET switch (refer to page 4) and
press the c button again.
If not ejecting, consult your Alpine dealer.
T – – –
• No CD is inserted.
- Insert a CD.
Indication for CD Changer
– – – H
• Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature
returns to within operation range.
E - 01
• Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject
button and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your
Alpine dealer.
• Magazine ejection not possible.
- Press the magazine eject button. If the magazine does
not eject, consult your Alpine dealer.
– – – –
• No magazine is loaded into the CD Changer.
- Insert a magazine.
T – – –
• No indicated disc.
- Choose another disc.
E E E E
• Misconnection or disconnection of CD Changer.
- Check connection between CD Changer and control
unit.

Specifications

FM TUNER SECTION
Tuning Range
Mono Usable Sensitivity
50 dB Quieting Sensitivity
Alternate Channel Selectivity 80 dB
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
AM TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
CD PLAYER SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
PICKUP
Wave length
Laser power
GENERAL
Power Requirement
Power Output
*Primary amplifier ratings per CEA-2006 Standard
• Power output: measured at 4 Ohms and ≤ 1% THD+N
• S/N: 80 dBA (reference: 1 W into 4 Ohms)
Maximum Pre-Output Voltage 2 V/10 k ohms
Bass
Treble
Weight
CHASSIS SIZE
Width
Height
Depth
NOSEPIECE SIZE
Width
Height
Depth
Due to continuous product improvement, specifications and
design are subject to change without notice.
87.7 – 107.9 MHz
9.3 dBf (0.8 µV/75 ohms)
13.5 dBf (1.3 µV/75 ohms)
65 dB
35 dB
2.0 dB
530 – 1,710 kHz
22.5 µV/27 dB
5 – 20,000 Hz (±1 dB)
Bleow measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
795 nm
CLASS I
14.4 V DC
(11–16 V allowable)
18 W RMS × 4*(CDM-
9823 only)
16W RMS × 4*(CDM-9821
only)
±14 dB at 60 Hz
±14 dB at 10 kHz
1.5 kg (3 lbs. 5 oz)
178 mm (7")
50 mm (2")
160 mm (6-1/4")
170 mm (6–3/4")
46 mm (1-13/16")
20 mm (11/16")
13
-EN