ADTRAN 1200 Specifications

QUAD IMA
QUAD IMA
CLEI: VAPMEH0D_ _
1179611L1
DESCRIPTION
The Quad IMA Module terminates up to 4 T1s (DSX-1 or DS1) and performs
Inverse Multiplexing over ATM (IMA) for up to 4 T1 IMA links in the Total Access
1200. It can provide up to 24 ports of ADSL plus POTS toward customers.
The following features are supported on the Quad IMA Module:
I Performs Inverse Multiplexing over ATM (IMA) for up to four T1 IMA links
I Support one to four T1s (both short and long haul DSX-1 and DS1)
Supports one IMA group
I
The type, DS1 or DSX1, and line buildout, 0-133 up to 533-655 feet, are
I
provisionable to accommodate both short and long haul T1s
I Accepts RJ-48 type connectors transporting the T1 signals
I Operates over an extended temperature range –40°C to +70°C
Front Panel indication of T1/E1 status
I
Front access to all connections
I
I Offers provisioning and alarm monitoring via SNMP and TL1 through the local
craft interface and ATM in-band management channel
I Interoperable with any ATM DS1 IMA device that is built to current IMA
specifications which includes the Total Access 3000 IMA Aggregation System
I Meets NEBS Level 3, GR-1089-CORE and UL 60950
CONNECTIONS
The Quad IMA Module plugs directly into the Total Access 1200 (19- or 23-inch)
rack mounted shelf. Each T1 is connected to the front of the module through an
RJ-48 plug.
TURN-UP STEPS
To install the Quad IMA Module, perform the following steps:
1
After unpacking the Quad IMA Module, inspect it for damage. If damage is
found, file a claim with the carrier and then contact ADTRAN
Service.
2
ADTRAN recommends that all power be removed from the Total Access 1200
before removing or replacing the Quad IMA Module.
3
Loosen screws on the previous card and remove it, if so equipped.
4
Insert new module in the slots on the left and right and slide it securely into
place.
5
Tighten screws to keep it securely in place.
6
Insert the T1 cables with the RJ-48 plugs in the jacks on the front of the module.
C A U T I O N C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
7
Restore power to the Total Access 1200.
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
TOTAL ACCESS 1200 QUAD IMA MODULE
Module
1 2
1 2 3 4
FRONT PANEL LED
G G
T1/E1
T1/E1
G
✷
G
✷
3 4
T1/E1
G
OPERATIONAL SPECIFICATIONS
I Operates over extended temperature range of (–40°C to +70°C)
®
I Storage –40°C to +85°C. Relative humidity to 95 percent, noncondensing.
COMPLIANCE
This product is NRTL listed to the applicable UL standards. This product is intended to be
installed in a Type "B" or "E" enclosure in a Restricted Access Only area. The Total Access 1200
shelf Frame Ground terminal must be connected to an earth ground.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Code
Power Code (PC)
Telecommunication Code (TC)
Installation Code (IC)
Changes or modifications not expressly approved by ADTRAN could void the user's authority
to operate this equipment.
WARRANTY
ADTRAN will replace or repair this product within the warranty period if it does not meet its
published specifications or fails while in service. Warranty information can be found at
www.adtran.com/warranty. U.S. and Canada customer Faxback: 877-457-5007,
Document 414.
® Customer
I For a complete Installation and Maintenance Practice (P/N 61179611L1-5): 877-457-5007,
S
Off Facility Unassigned
Green All Good, IMA in Sync
Flashing Green T1/E1 OK, no IMA Sync
Yellow Signal present OOF
Flashing Yellow T1 is in loopback
Red No signal
Input Output
F C
– X
A –
Faxback Document 936. Please have your fax number ready. I
JOB
A
ID
61179611L1-22B
0402