Toshiba DVR620KU Owner's Manual page 104

Symptom
DV signal cannot be input.
The DVC cannot be operated with this
unit.
D
V
Certain functions of the unit cannot
D
operate.
•
V
C
DV audio signal cannot be switched.
R
No image from HDMI connection.
There is no picture.
Picture noise appears.
Playback picture from the external
devices connected to this unit is
distorted.
There is no sound.
Sound is noisy.
D
The disc does not play back.
V
D
Playback image freezes for a second.
Discs recorded on this unit cannot be
played back on other DVD players.
104 EN 104 EN
E9PKAUD_DVR620KU_EN.indd 104 E9PKAUD_DVR620KU_EN.indd 104
TROUBLESHOOTING
Remedy
• Before connection, turn on the power supplies for both this unit and the
DVC, and make sure that these units are in stop mode.
• Only a "DVC-SD" signal can be input from the DVC to this unit. Other
types of signals are not supported.
• Do not connect any device other than the DVC. Even if a recorder or PC
with another DV terminal is connected, the DV function will not operate.
• If the DVC is not recognized after connection, turn off the power supply
for the unit and re-connect the DVC.
• Signal input or DVC operation from this unit may be disabled
depending on the type of DVC.
• If a DVC signal cannot be input, use an external input (L1 (Rear)/L2
(front)) for analog connection via audio/video cables.
• DVC control may be disabled depending on the type of DVC, even in a
mode other than camera mode. In this case, switch to DVD control and
execute the normal recording procedure while operating the DVC.
• Some functions may not operate depending on the type of DVC. For
example, if the DVC does not support slow playback mode, the slow
playback function is disabled.
• With L3 (DV-IN), the disc display menu does not appear unless disc
playback is executed.
• For recording with the DVC, the recording audio signal can be set to 12
bits or 16 bits. However, when 16-bit recording mode is selected, audio
signal cannot be switched. To record an audio signal, set it to 12 bits.
• Check the HDMI connection. (Check the status of the HDMI related
indications.)
• Check whether the connected monitor device or other device supports
HDCP. (This unit will not output a video signal unless the other device
supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• If the unit is connected to the unauthorized display device with an
HDMI cable, the audio/video signal may not be output when playing
back a commercial DVD-video.
• If the setup menu appears on the TV screen, press [RETURN] to exit.
• Check if the progressive scan mode is set correctly according to your TV
(page 95).
• Clean the disc with a cleaning cloth.
• If the picture output signal from the external devices passes through this
unit to get to your TV, the copy protection signal applied to some DVD could
affect the picture quality. Disconnect the playback device in question and
connect it directly to your TV.
• If you are using DIGITAL AUDIO OUTPUT (COAXIAL) jack, check the setting
in "Audio Out" (page 90).
• Clean the disc with a cleaning cloth.
• Clean the disc with a cleaning cloth.
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM) (page 10).
• The region code on the DVD-video does not match the unit (page 10).
• Moisture has condensed inside the unit. Remove the disc and leave the
unit turned on for about 2 hours until the moisture evaporates (page 4).
• If the disc was recorded on another recorder, the unit cannot play back
the disc if it was not finalized.
• During the playback of 2 layered disc, picture may freeze for a moment
when the 1st layer switches to the 2nd layer. This is not a malfunction.
• If you are using DVD-RW/-R or DVD+R, please ensure you finalized the
disc after recording (pages 31-33).
3/25/2009 3:49:11 PM 3/25/2009 3:49:11 PM