Troubleshooting; Completing The Installation - Samsung SCX-3200 Series User Manual

1. Check whether the network cable is connected to the machine. If not,
connect the machine with a standard network cable.
2. Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine's new IP address in the browser window.
For example,
3. Click Login on the upper right of the SyncThru™ Web Service
website.
The Login window appears.
4. Type in the ID and Password then click Login.
If it's your first time logging into SyncThru™ Web Service, type in the
below default ID and password.
• ID: admin
• Password: sec00000
5. When the SyncThru™ Web Service window opens, click Network
Settings.
6. Click Wireless > Wizard.
Wizard will help you setup the wireless network configuration.
However, if you want to set the wireless network directly, select
Custom.
7. Select the one Network Name(SSID) in the list.
• SSID: SSID (Service Set Identifier) is a name that identifies a
wireless network. access points and wireless devices attempting
to connect to a specific wireless network must use the same
SSID. The SSID is case-sensitive.
• Operation Mode: Operation Mode refers to the type of wireless
connections (See "Wireless network name and network key" on
page 37).
- Ad-hoc: Allows wireless devices to communicate directly with
each other in a peer-to-peer environment.
- Infrastructure: Allows wireless devices to communicate with
each other through an access point.
If your network's Operation Mode is Infrastructure, select the
SSID of the access point. If the Operation Mode is Ad-hoc,
select the machine's SSID. Note that "airportthru" is the default
SSID of your machine.
8. Click Next.
If wireless security setting window appears, enter the registered
password (network key) and click Next.
9. The confirmation window appears, please check your wireless setup.
If the setup is right, click Apply.
Disconnect the network cable (standard or network). Your
machine should then start communicating wirelessly with the
network. In case of Ad-hoc mode, you can use a wireless LAN
and wired LAN simultaneously.

COMPLETING THE INSTALLATION

After you have installed your Samsung wireless network printer, print
another copy of the Network Configuration Report and keep it for future
reference. You are now ready to use your new Samsung wireless printer on
your network.

TROUBLESHOOTING

Solve problems that might occur during wireless setting and installing the
machine driver.
Wireless network problems
If problems occur while using the machine on a network, check the
followings.
Wireless network setup (SCX-3205W(K))_ 44
Printers Not Found
• Your machine may not be turned on. Turn on your computer and the
machine.
• USB cable is not connected between your computer and machine.
Connect machine to your computer using the USB cable.
• The machine does not support wireless network. Check the
machine's user's guide included on the software CD supplied with
your machine and prepare a wireless network machine.
Connecting Failure - Not found SSID
• The machine is unable to search network name (SSID) which you
have selected or typed in. Check the network name (SSID) on your
access point and try connecting again.
• Your access point is not turned on. Turn on your access point.
Connecting Failure - Invalid Security
• You configured security incorrectly. Check the configured security on
your access point and machine.
Connecting Failure - General Connection Error
• Your computer is not receiving a signal form your machine. Check
the USB cable and your machine power.
• When Temporal Key Integrity Protocol(TKIP) security is set up for
the access point, connection might fail. Change the access point
settings.
Connecting Failure - Connected Wired Network
• Your machine is connected with wired network cable. Remove the
wired network cable from your machine.
PC Connection Error
• The configured network address is unable to connect between your
computer and machine.
- For DHCP network environment
The print receives the IP address automatically (DHCP) when
computer is configured to DHCP.
- For Static network environment
The machine uses the static address when computer is
configured to static address.
If you computer has following addresses,
- IP address: 192.168.1.100
- Subnet address: 255.255.255.0
- Gateway address: 192.168.1.1
Type in the following address for your machine,
- IP address: 192.168.1.101
- Subnet address: 255.255.255.0
- Gateway address: 192.168.1.1