Page 1 SyncMaster P50HP ,P50FP ,P63FP PDP Monitor User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3: Installation
Ensure that the power plug is plugged into the power outlet firmly and correctly. • Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Do not connect multiple appliances to the same power outlet. •...
Page 4 Keep heating appliances as far away from the power cord or the product as possible. • Do not install it in a badly ventilated location such as a bookcase or closet. • When putting the product down, make sure to put it down softly. •...
Page 5 When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • When cleaning the product, make sure to disconnect the power cord. • When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. •...
Page 6 If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. •...
Page 7 If you continually move closer to the product screen, your eye- sight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Page 8 The batteries (and rechargeable batteries) are not ordinary re- fuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Page 9: Checking The Contents Of The Package
Introduction Package Contents Note Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package...
Page 10 Introduction Manuals Quick Setup Guide Cables Power Cord Others Remote Control Sold separately D-Sub Cable Semi Stand KIT (Applicable to the P50HP, P50FP model only) To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.
Page 11 • • Your PDP Display Front SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only al- lowed for external devices that are connected to the PDP Display at the time. [PC] → [DVI] → [AV] → [HDMI] → [Component] → [BNC] Enter button [ ] Activates a highlighted menu item.
Page 12 Power button [ Use this button for turning the PDP Display on and off. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods.
Page 13 RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB IN (PC Video Connection Terminal) Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) DVI IN (PC Video Connection Terminal) Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DVI / PC / HDMI IN [DVI/PC/HDMI AU- DIO IN] (PC/DVI/HDMI Audio Connection...
Page 14: Remote Control
Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display , causing a malfunction due to interference with the frequen- BNC OUT [R/PR, G/Y, B/PB, H, V] (BNC Terminal (Output)) BNC (Analog PC) Connection: connecting...
Page 15 POWER 3. Number Buttons 4. DEL button POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO Color Buttons TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. Turns the product Off.
Page 16 5. + VOL - MUTE 7. TV/DTV MENU INFO 11. Color Buttons TTX/MIX 13. STILL 14. AUTO 15. S.MODE 16. MDC 17. LOCK SOURCE ENTER/PRE-CH CH/P 21. D.MENU 22. GUIDE Adjusts the audio volume. Pauses (mutes) the audio output temporarily. This is dis- played on the lower left corner of the screen.
Page 17 RETURN 24. Up-Down Left-Right but- tons EXIT 27. MagicInfo 28. P.MODE DUAL/MTS SWAP Returns to the previous menu. Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Exits from the menu screen. Selects SRS TruSurround XT mode. MagicInfo Quick Launch Button.
Page 18 Introduction Mechanical Layout (P50HP, P50FP) Mechanical Layout PDP Display Head...
Page 19 • At least 2 persons are needed in order to move the PDP Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Page 20: Wall Bracket Installation
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 21 Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Page 22 Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
Page 23 Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 24: Mechanical Layout
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 25 Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
Page 26 Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
Page 27 Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
Page 28 Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
Page 29: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance.
Page 30: Connecting Av Devices
Turn on both your computer and the PDP Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Page 31: Connecting To A Camcorder
Connecting to a Camcorder Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the PDP Display.
Page 32: Connecting A Dtv Set Top Box
Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the PDP Display or on the remote control. • Then, start the DVD Player with a DVD disc inserted. Note • A component cable is optional.
Page 33 Connecting Using a HDMI Cable Note • Input devices such as digital DVD are connected to the HDMI IN terminal of the PDP Display using the HDMI cable. • You cannot connect a PC to the HDMI IN terminal. Connecting Using a DVI Cable Note •...
Page 34: Connecting To An Audio System
Connections Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on PDP Display.
Page 35: Main Screen
Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Page 36: Port Selection
Main Icons Remocon Safety Lock Port Selection 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
Page 37: Power Control
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
Page 38 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display. 1) Power On/Off...
Page 39: Input Source
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
Page 40: Image Size
Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
Page 41 Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
Page 42 Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
Page 43: Pip Size
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
Page 44: Pip Source
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
Page 45 Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC.
Page 46 Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
Page 47 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 48: Image Lock
Settings Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar.
Page 49: Maintenance
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal.
Page 50 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
Page 51: Video Wall
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
Page 52: Troubleshooting
Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 LCD Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
Page 53 - Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict. - Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu) Note : A Display Set ID must be a value between 0 and 25 .
Page 54 Adjusting the PDP Display Input Available Modes • PC / DVI / BNC • • HDMI • Component Source List MENU → ENTER → [Input] → ENTER → [Source List] → Use to select PC, DVI or other external input sources connected to the PDP Display. Use to select the screen of your choice.
Page 55: Available Modes
Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC Note •...
Page 56 For watching motion pictures such as a DVD or VCR. Internet Medium brightness For working with a mixture of images such as texts and graphics. Text Normal brightness For documents or works involving heavy text. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Page 57: Color Tone
Color Tone MENU → → ENTER → [Picture] → The color tones can be changed. Cool Normal Warm Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled. If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance.
Page 58 Blue MENU → → ENTER → [Picture] → ENTER → [Blue] → , Color Temp. MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER Color Temp. is a measure of the 'warmth' of the image colors. Note This function is only enabled if the Color Tone is set to Off.
Page 59 V-Position MENU → → ENTER → [Picture] → → ENTER → [V-Position] → , Adjusts the screen location vertically. Auto Adjustment MENU → → ENTER → [Picture] → The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed.
Page 60 G-Gain MENU → → ENTER → [Picture] → Balance] → → ENTER → [Signal Control] → → ENTER → [G-Gain] → , → ENTER B-Gain MENU → → ENTER → [Picture] → Balance] → → ENTER → [Signal Control] → ENTER R-Offset MENU →...
Page 61 The Size can be switched. 16:9 Picture [ AV / HDMI / DVI / COMPONENT] Available Modes • PC / DVI / BNC • • HDMI / DVI • Component Mode MENU → → ENTER → [Picture] → ENTER → [Mode] → The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie"...
Page 62 Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → ness] → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → → ENTER [Sharpness] → , Adjusts the picture Sharpness. Color MENU → → ENTER → [Picture] → →...
Page 63: Color Temp
Cool2 Cool1 Normal Warm1 Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled. Color Temp. MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER Color temp.
Page 64: Film Mode
ZOOM1, ZOOM2 will be unavailabel in HDMI mode. Note The Position and Reset functions are available when Zoom1 or Zoom2 is run. Digital NR (Digital Noise Reduction) MENU → → ENTER → [Picture] → → ENTER Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images.
Page 65 • Component Mode MENU → → → ENTER → [Sound] → ENTER → [Mode] → The PDP Display has a built-in high fidelity stereo amplifier. Standard Selects Standard for the standard factory settings. Music Selects Music when watching music videos or concerts. Movie Selects Movie when viewing movies.
Page 66: Auto Volume
Treble MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] → → ENTER Emphasizes high frequency audio. Balance MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Bal- ance] →...
Page 67 Note The direct button on the remote control is the 'SRS' button. Setup Available Modes • PC / DVI / BNC • • HDMI • Component Language MENU → → → → ENTER → [Setup] → ENTER → [Language ] → You can choose one of 13 languages.
Page 68 Current Time Setting. Sleep Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → ENTER→ [Sleep Timer] → → ENTER Turns the PDP Display off automatically at certain times. On Timer MENU → →...
Page 69: Menu Transparency
Turns the PDP Display off automatically at a preset time. Menu Transparency MENU → → → → ENTER → [Setup] → → → ENTER Change the transparency of the background of the OSD. High Medium Opaque Safety Lock PIN MENU → →...
Page 70 Note The preset password for the PDP Display is "0000" Initializing the Safety Lock pin number: INFO + EXIT + MUTE Energy Saving MENU → → → → ENTER → [Setup] → → → → → ENTER This feature adjusts the power consumption of the unit in order to save energy. HDMI Black Level MENU →...
Page 71 Note When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available. Video Wall does not operate in MagicInfo mode. Video Wall MENU → → → → ENTER → [Setup] → → → → Wall ]→ ENTER → [Video Wall ] → Turns Off/On the Video Wall function of the selected display Off/On.
Page 72: Safety Screen
Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5. Vertical MENU → → → → ENTER → [Setup] → → → → Wall ]→ → ENTER → [Vertical] → → →...
Page 73 • The Safety Screen function scrolls the screen for the specified period of time. • This function is not available when the power is turned off. MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] Pixel Shift Pixel Shift...
Page 74 Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → Set the time interval for performing the horizontal or vertical movement, respectively.
Page 75 You can change the Safety Screen Type. Scroll Eraser All White Pattern Period MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → Use this function to set the execution period for each mode set in the timer. Time MENU →...
Page 76 Scroll MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Scroll] → This function prevents after-images on the screen by moving all the pixels on the PDP ac- cording to a pattern.
Page 77: Resolution Select
This function prevents after-images on the screen by changing the color of pixels to white. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time. Pattern MENU →...
Page 78: Power On Adjustment
1280 X 768 1360 x 768 1366 X 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz. Power On Adjustment MENU →...
Page 79 MENU → → → → ENTER → [Setup] → → → → → ENTER → [Reset ] Image Reset MENU → → → → ENTER → [Setup] → → → → → ENTER → [Reset ]→ ENTER → [Image Reset ] → , → ENTER Note Available in PC mode only Note...
Page 80: Multi Control
Multi Control Assigns an individual ID to the SET. MENU → → → → • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.
Page 81: Troubleshooting
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the PDP Display. Unplug the video cable from the back of the computer. Turn on the PDP Display.
Page 82: Symptoms And Recommended Actions
• Do not use benzene, thinner or other flammable sub- stances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.)
Page 83 Check if the signal cable between the computer and the PDP Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the PDP Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the PDP Display is on.
Page 84 The screen color is inconsistent. Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 85 Check if the batteries are empty. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card.
Page 86 Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer.
Page 87: Specifications
Specifications General General Model Name PDP Panel Size SyncMaster P50HP SyncMaster P50FP SyncMaster P63FP Display area SyncMaster P50HP SyncMaster P50FP SyncMaster P63FP Pixel Pitch SyncMaster P50HP SyncMaster P50FP SyncMaster P63FP Synchronization Horizontal Vertical Display Color 16.7 M Resolution Optimum resolu- P50HP tion P50FP...
Page 88 Input Signal, Terminated Separate H/V sync, Composite, SOG(Option) TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 165MHz (Analog,Digital) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal connectors D-sub, DVI-D, BNC, AV(Composite, CVBS), HDMI, RS232C In/Out PC Audio In, Audio In(Stereo), Audio Out(Stereo)
Page 89 Plug and Play Capability This PDP Display can be installed on any Plug & Play compatible system. The interaction of the PDP Display and the computer systems will provide the best op- erating conditions and PDP Display settings. In most cases, the PDP Display installation will proceed automatically, unless the user wishes to select alternate settings.
Page 90: Preset Timing Modes
This monitor is EPA ENERGY STAR ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality. ® As an ENERGY STAR Partner, SAMSUNG has deter- mined that this product meets the ENERGY STAR guidelines for energy efficiency. Horizontal Vertical Fre-...
Page 91 Display Mode Horizontal Frequency (kHz) MAC, 640 x 480 35.000 MAC, 832 x 624 49.726 MAC, 1152 x 870 68.681 VESA, 640 x 480 37.861 VESA, 640 x 480 37.500 VESA, 800 x 600 35.156 VESA, 800 x 600 37.879 VESA, 800 x 600 48.077 VESA, 800 x 600...
Page 92: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP. •...
Page 93 Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. •...
Page 94: Select Method
• Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement. • All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
Page 95 - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) •...
Page 96 • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble )
Page 97 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINA BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP.
Page 98 022 - 607 - 93 - 33 PORTUGAL (7267864) SLOVAKIA 0800-SAMSUNG (726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG(902 172 678) SWEDEN 075 - SAMSUNG (726 78 64) http://www.samsung.com/se SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min) 0845 SAMSUNG (7267864) ESTONIA 800-7267 LATVIA 8000-7267...
Page 99 010-6475 1880 HONG KONG:3698 - 4698 http://www.samsung.com/hk 3030 8282 http://www.samsung.com/in 1-800-3000-8282 1800 110011 0800-112-8888 http://www.samsung.com/id 0120-327-527 http://www.samsung.com/jp 1800-88-9999 http://www.samsung.com/my 0800 SAMSUNG(0800 726 http://www.samsung.com/nz 786) 1-800-10-SAMSUNG http://www.samsung.com/ph (726-7864) 1-800-3-SAMSUNG (726-7864) 02-5805777 1800-SAMSUNG(726-7864) http://www.samsung.com/sg 1800-29-3232, 02-689-3232 http://www.samsung.com/th 0800-329-999 http://www.samsung.com/tw 1 800 588 889 http://www.samsung.com/vn...
Page 100: Correct Disposal
Interlace and Non-Interlace Methods Plug & Play Resolution SRS TS XT Multiple Display (MDC) Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called...
Page 101 Reproduction in any manner whatsoever without the written permission of Samsung Elec- tronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this ma- terial.
Page 102 Appendix...

This manual is also suitable for:

Syncmaster p50hp Syncmaster p63fp

Samsung SyncMaster P50FP User Manual

Quick Links

Troubleshooting

Related Manuals for Samsung SyncMaster P50FP

Summary of Contents for Samsung SyncMaster P50FP

This manual is also suitable for:

Table of Contents