Page 1
RX-V640RDS AV Receiver DSP-AX640SE AV Amplifier OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING...
Page 2
Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
Before connecting components ... 9 Connecting video components ... 10 Connecting audio components ... 12 Connecting the antennas RX-V640RDS Connecting an external amplifier ... 14 Connecting an external decoder ... 14 Connecting the speakers ... 15 Connecting the power supply cords ... 18 Turning on the power ...
N Preset station shifting capability (Preset editing) I About this manual • This document is the owner’s manual for both RX-V640RDS and DSP-AX640SE. Since DSP-AX640SE does not incorporate a tuner, descriptions on tuning are not applicable for DSP-AX640SE. Illustrations for the RX-V640RDS are mainly used for explanations.
UM-4) according to the polarity markings on the inside of the battery compartment. Slide the cover back on so that it snaps into place. GETTING STARTED RX-V640RDS AM loop antenna 75-ohm/300-ohm antenna adapter (U.K. model) I Notes on batteries • Change all of the batteries if you notice a decrease in the operating range of the remote control, that the indicator does not flash, or the light becoming dim.
6 Front panel display Shows information about the operational status of the unit. 7 TUNING MODE (AUTO/MAN’L MONO) RX-V640RDS Switches the tuning mode between automatic and manual. 8 PRESET/TUNING (EDIT) Switches the function of PRESET/TUNING l / h between selecting a preset station number and tuning (the colon (:) turns on or off).
Page 7
Selects preset station groups A to E when the unit is in tuner mode. NEXT Selects the set menu mode ( RX-V640RDS not in tuner mode.) u PRESET/TUNING l / h Select preset station numbers 1 to 8 when a colon (:) is displayed in the front panel display.
CONTROLS AND FUNCTIONS Remote control This section describes the controls and functions of the remote control. Make sure that the AMP mode is selected before use. TRANSMIT CODE SET POWER POWER STANDBY MD/CD-R TUNER D - TV/CBL V - AUX VCR 1 VCR2/DVR TV VOL...
u MUTE Mutes the sound. Press again to restore the audio output to the previous volume level. i STEREO/EFFECT Switches between normal stereo and DSP effect reproduction. When you select STEREO the unit mixes down all Dolby Digital and DTS signals (except the LFE channel) as well as those 2-channel signals without effect sounds, to the main left and right speakers.
Displays the sound field management the unit is using when you listen to a DSP sound field program. 6 AUTO indicator RX-V640RDS Shows that this unit is in the automatic tuning mode. 7 MUTE indicator Flashes while the MUTE function is on.
COMPORNENT VIDEO D-TV /CBL OUTPUT MONITOR CENTER TUNER REAR REAR MAIN (SURROUND) CENTER WOOFER SPEAKERS 75Ω UNBAL. MAIN CENTER SUBWOOFER OUTPUT jack (page 17) RX-V640RDS Speaker terminals (page 17) OUTPUT jacks (page 14) REAR (SURROUND) REAR CENTER AC OUTLETS (page 18)
CONNECTIONS Connecting video components Refer to the connection examples on the next page. I Types of video jacks COMPONENT VIDEO VIDEO S VIDEO 1 VIDEO jack Conventional composite video signal. 2 S VIDEO jack Transmits color and luminance separately and achieves high-quality color reproduction.
Page 13
DVD player OPTICAL OUTPUT AUDIO OUTPUT AUDIO AUDIO VIDEO VIDEO S VIDEO DIGITAL INPUT D-TV /CBL COAXIAL OPTICAL D-TV/CBL (PLAY) VCR-1 /CD-R (REC) MD/CD-R MAIN VCR 2 /DVR SURROUND MD/CD-R MONITOR OUT OPTICAL VIDEO S VIDEO DIGITAL WOOFER CENTER OUTPUT 6CH INPUT AUDIO AUDIO...
CONNECTIONS Connecting audio components I Connecting a CD player Connect the coaxial digital output jack on your CD player to the DIGITAL INPUT CD jack on this unit. • Use the AUDIO jacks on this unit for a CD player which does not have coaxial digital output jack.
(inch) reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas. FREQUENCY STEP switch (China and General models only)
Rear center channel line output jack. 5 SUBWOOFER jack When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack in accordance with your SPEAKER SET selections.
LFE (low-frequency effect) channel with high fidelity when playing back Dolby Digital or DTS signals. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction. I Speaker placement Refer to the following diagram when you place the speakers.
CONNECTIONS I Connections Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) in accordance with the markers on this unit, the speakers, and the speaker cables. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
Page 19
A rear center speaker can be connected to these terminals. SUBWOOFER jack When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. This unit will direct low bass signals distributed from the main, center and/or rear channels to this jack in accordance with your SPEAKER SET selections.
CONNECTIONS Connecting the power supply cords VOLTAGE SELECTOR VOLTAGE SELECTOR AC OUTLETS SWITCHED IMPEDANCE SELECTOR SET BEFORE POWER ON MAIN A OR B : 4ΩMIN. /SPEAKER MAIN A OR B : 8ΩMIN. /SPEAKER A+B : 8ΩMIN. /SPEAKER A+B : 16ΩMIN. /SPEAKER CENTER 6ΩMIN.
BASIC SYSTEM SETTINGS The “BASIC” menu allows you to set some of the basic “SOUND” menu parameters with a minimum of effort. If you wish to configure the unit more precisely to suit your listening environment, use the more detailed parameters from the “SOUND”...
BASIC SYSTEM SETTINGS SET MENU BASIC SOUND 1 SETUP Press j / i to alter the settings for each parameter. Use d to move to the next setting. 1 ROOM Choose from S/M/L. 2 SUBWOOFER Choose either of YES/NONE. 3 SPEAKERS Choose from 2/3/4/5/6 spk.
Setting the unit to match your speaker system Follow the instructions below to set the amplifier output to match the size of your room and speakers. Press u / d to cycle through parameters 1 through 4, and j / i to alter the parameter setting.
INPUT STANDBY INPUT MODE 6CH INPUT SILENT SPEAKERS STEREO PROGRAM A/B/C/D/E PRESET/TUNING EFFECT NEXT SET MENU PHONES S VIDEO CODE SET TRANSMIT SYSTEM POWER POWER STANDBY POWER MD/CD-R TUNER SLEEP D-TV/CBL V-AUX 6CH INPUT VCR 1 VCR2/DVR TV VOL TV CH VOLUME –...
Page 25
Start playback or select a broadcast station on the source component. Refer to the operation instructions for the component. Adjust the volume to the desired level. The volume level is displayed digitally. Example: –70 dB Control range: VOLUME MUTE (minimum) to 0 dB (maximum) The volume level indicator also shows the current volume level as a bar graph.
PLAYBACK Input modes and indications This unit is equipped with a variety of input jacks. You can select the type of input signals you wish to use. Each time you turn on the unit power, the input mode is set to the “INPUT 2 INPUT MODE” setting defined in the set menu.
Selecting a sound field program You can enhance your listening experience by selecting a DSP program. For details about each program, see pages 28 – 30. STANDBY SILENT SPEAKERS STEREO PROGRAM A/B/C/D/E PRESET/TUNING NEXT SET MENU EFFECT PHONES S VIDEO VIDEO PROGRAM l / h CODE SET...
Page 28
PLAYBACK I Selecting PRO LOGIC, PRO LOGIC II or Neo:6 You can listen to 2-channel sources decoded into five or six discrete channels by selecting PRO LOGIC, PRO LOGIC II or Neo:6 in program No. 9. STANDBY SILENT SPEAKERS STEREO PROGRAM A/B/C/D/E PRESET/TUNING...
I Virtual CINEMA DSP With Virtual CINEMA DSP, you can enjoy all DSP programs without rear speakers. It creates virtual speakers to reproduce a natural sound field. You can listen to virtual CINEMA DSP by setting “1C REAR LR” in the set menu to NON. Sound field processing changes to VIRTUAL CINEMA DSP automatically.
The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound field. YAMAHA’s DSP requires four effect speakers to recreate sound fields based on the measured sound field data. The processor controls the strength and delay time of the signals output from the four effect speakers to localize the virtual sound sources and fully encompass the listener.
CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field programs to provide a surround sound field. It recreates comprehensive movie sound design in your audio room. In CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the Main left and right, and...
Page 32
CINEMA-DSP I For movie programs Program MOVIE Spectacle THEATER 1 Sci-Fi MOVIE Adventure THEATER 2 General Straight Decode Enhanced Mode Straight Decode This unit is equipped with various precise decoders; • Dolby Digital/DTS decoder for multi-channel reproduction of the original sound •...
Both decoders have two modes, MOVIE/CINEMA for movies, and MUSIC for 2- channel sources. These programs use YAMAHA’s tri-field DSP processing on each of the Dolby Digital or DTS signals for the front, left surround, and right surround channels. This...
VCR1 V-AUX PRESET/TUNING AM 1440 kHz EDIT TUNING RX-V640RDS Press PRESET/TUNING l / h once to begin automatic tuning. Press h to tune in to a higher frequency, or press l to tune in to a lower frequency. VOLUME PRESET/TUNING FM/AM...
However, if the power is cut for more than one week, the preset stations may be cleared. If so, store the stations again. AUTO Lights up TUNER AUTO MEMORY TUNING RX-V640RDS...
Page 36
TUNING RX-V640RDS I Manually presetting stations You can store up to 40 stations (8 stations x 5 groups) manually. INPUT STANDBY INPUT MODE 6CH INPUT SILENT SPEAKERS STEREO PROGRAM A/B/C/D/E PRESET/TUNING EFFECT NEXT SET MENU PHONES S VIDEO Tune in to a station.
Press PRESET/TUNING (EDIT) again. SELECT The stations stored at the two preset assignments are exchanged. Remote control PRESET/TUNING EDIT TUNER TUNED TUNING RX-V640RDS VOLUME PRESET/TUNING FM/AM EDIT TUNING MODE MEMORY AUTO/MANUAL MONO MAN`L/AUTO FM BASS VIDEO AUX STEREO PROGRAM A/B/C/D/E...
“CT WAIT” may appear if the data is accidentally cut off. I EON (Enhanced Other Networks): Refer to the following page. RX-V640RDS Changing the RDS mode This unit provides four modes for displaying RDS data. The PS, PTY, RT and/or CT mode indicators that...
• When broadcasting of the required program ends, the unit returns to the previous station (or another program on the same station). I To cancel this function Press EON repeatedly until the program type name disappears from the front panel display. RECEIVING RDS STATIONS RX-V640RDS...
Use this feature to automatically set this unit in standby mode after the amount of time you have set. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off the external component(s) connected to AC OUTLET(S).
Recording adjustments and other operations are performed on other recording components. Refer to the operation instructions for these components for details on their operation . INPUT STANDBY INPUT MODE 6CH INPUT SILENT VIDEO AUX SPEAKERS STEREO PROGRAM A/B/C/D/E PRESET/TUNING NEXT SET MENU EFFECT PHONES...
You can set the following parameters on the set menu to obtain a better sound from the unit. Change the settings to reflect the needs of your listening environment. Set menu list The set menus are divided by use and function into the 4 categories listed here.
Press j / i once to enter the setup mode of the selected item. The last setting you adjusted appears on the front panel display. Depending on the menu item, press u/d to select a sub item. Press j / i repeatedly to change the menu item setting.
Page 44
SET MENU I 1B MAIN (main speaker mode) Choices: LARGE, SMALL LARGE Select this if you have large main speakers. The unit directs the entire range of the main left and right channel signals to the main left and right speakers. SMALL Select this if you have small main speakers.
SOUND 2 SP DISTANCE (speaker distance) Use this feature to adjust the delay applied to center and rear center channel sounds. This feature works when there is sound output from the center speakers with a source such as Dolby Digital or DTS. Ideally, the center speaker and the rear speakers should be the same distance from the main listening position as the left and right main speakers.
SET MENU SOUND 5 CENTER GEQ (center graphic equalizer) Use this feature to adjust the built-in 5-band graphic equalizer so that the center speaker tonal quality matches that of the left and right main speakers. You can select the 100 Hz, 300 Hz, 1 kHz, 3 kHz, or 10 kHz frequencies. Control range (dB): –6 to +6 Initial setting: 0 dB for 5-band Press d to select a higher frequency and u...
INPUT 2 INPUT MODE (initial input mode) Use this feature to designate the input mode for sources connected to the DIGITAL INPUT jacks when you turn this unit on (see page 24 for details about the input mode). Choices: AUTO, LAST AUTO Select this setting to allow the unit to automatically detect the type of input signal and select the appropriate input...
SET MENU OPTION 4 ZONE SET I SP B (speaker B set) Use this feature to select the location of the main speakers connected to the SPEAKERS B terminals. Choices: MAIN, ZONE B MAIN Select this to turn on/off SPEAKERS A and B when the speakers connected to the SPEAKERS B terminals are set in the main room.
REMOTE CONTROL FEATURES In addition to controlling this unit, the remote control can operate other A/V components made by YAMAHA and other manufacturers. To control other components, set up the remote control with the appropriate manufacturer codes. Control area I Controlling this unit The shaded areas below can be used to control this unit when the AMP mode is selected.
I Clearing setup manufacturer code for the component control Press an input selector button or ## to select the component control for which you want to clear the manufacturer code. Manufacturer Code YAMAHA 0005 YAMAHA 0024 YAMAHA 0003 YAMAHA 0098 Press CODE SET by using a ballpoint pen or –...
Controlling other components You can operate other components if you have set the manufacturer code for your component in the remote control. Note, however, that some buttons may not operate the component correctly. Once you select an input source, the remote control switches to the mode for operating the component.
SETTING THE SPEAKER LEVELS Adjusting the volume during playback You can adjust the volume of the speakers while listening to sound playback. VCR 1 VCR2/DVR TV VOL TV CH VOLUME – – – TV MUTE TV INPUT MUTE ROCK ENTER- HALL JAZZ CLUB CONCERT...
SOUND FIELD PROGRAM PARAMETER EDITING Changing parameter settings The initial sound field program settings will provide you with an excellent listening experience as they are. It is not necessary to alter these settings, but you can create an original listening environment by doing so. Note •...
SOUND FIELD PROGRAM PARAMETER EDITING Digital sound field parameter descriptions You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your listening room. Not all of the following parameters are found in every program. I DSP LEVEL Function: This parameter adjusts the level of all the DSP effect sounds within a narrow range.
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center. I General...
Page 56
TROUBLESHOOTING Problem Only the speaker on Incorrect cable connections. one side can be heard. No sound from the The sound effect is switched off. effect speakers. A Dolby Surround, Dolby Digital or DTS decoding DSP program is being used with material not encoded with Dolby Surround, Dolby Digital or DTS.
Page 57
Problem No sound from the rear “SOUND 1C REAR LR” or “SOUND 1D center speaker. REAR CT” on the set menu is set to NON. The Dolby Digital EX or the DTS-ES decoder is not switched on. A “humming” sound can Incorrect cable connections.
Page 58
TROUBLESHOOTING I Tuner RX-V640RDS Problem FM stereo reception is The characteristics of FM stereo noisy. broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. There is distortion, and There is multipath interference.
Based on a wealth of actually measured data, YAMAHA CINEMA DSP uses YAMAHA original sound field technology to combine Dolby Pro Logic, Dolby Digital and DTS systems to provide the visual and audio experience of movie theater in the listening room of your own home.
Page 60
GLOSSARY I Virtual CINEMA DSP YAMAHA has developed a virtual CINEMA DSP algorithm that allows you to enjoy DSP sound field surround effects even without any rear speakers by using virtual rear speakers. It is even possible to enjoy virtual CINEMA DSP using a minimal 2-speaker system that does not include a center speaker.
Composite, S-Video ... 5 Hz to 10 MHz, –3 dB Component ... 5 Hz to 30 MHz, –3 dB SPECIFICATIONS FM SECTION RX-V640RDS • Tuning Range [U.S.A. and Canada models] ... 87.5 to 107.9 MHz [Other models] ... 87.50 to 108.00 MHz •...
Page 62
LIST OF MANUFACTURER’S CODES LISTE DES CODES FABRICANTS LISTE DER HERSTELLER-CODES LISTA ÖVER TILLVERKARKODER LISTA DEI CODICI DEL FABBRICANTE LISTA DE CÓDIGOS DE FABRICANTES LIJST MET FABRIKANTENCODES CLARIVOX CLATRONIC ADMIRAL 0411, 0451, 0911, CONCERTO 1021, 1081 CONDOR AIKO 0891 CONTEC AKAI 0061, 0101, 0231, CONTINENTAL EDISON...