Xerox Office Finisher LX User Manual
  1. Manuals
  2. Brands
  3. Xerox Manuals
  4. All in One Printer
  5. Office Finisher LX
  6. User manual
Xerox Office Finisher LX User Manual

Xerox Office Finisher LX User Manual

Xerox multifunction printer user guide
Hide thumbs

Advertisement

Table of Contents

Version 1.0
July 2008
Office Finisher LX

User Guide

Advertisement

Table of Contents
loading

Related Manuals for Xerox Office Finisher LX

Summary of Contents for Xerox Office Finisher LX

  • Page 1: User Guide

    Version 1.0 July 2008 Office Finisher LX User Guide...
  • Page 2 All product/brand names are trademarks or registered trademarks of the respective holders. The data saved in the hard disk of the machine may be lost if there is any problem in the hard disk. Xerox is not responsible for any direct and indirect damages arising from or caused by such data loss.Xerox is not responsible for any breakdown of machines due to infection of computer virus or computer hacking.

  • Page 3: Table Of Contents

    The Copy Output Screen Installing the Tray Attachment Loading Staples in the Automatic Stapler Loading Booklet Maker Staples Clearing Staple Jams Clearing Paper Jams Emptying the Hole Punch Waste Container Office Finisher LX - User Guide Table of Contents 1-10 1-14 1-17...

  • Page 4: Product Overview

    Product Overview Product Overview The Office Finisher LX is an optional device that can be used to staple your printed or copied output. The optional Booklet Maker can be used to hole punch and crease your output. Descriptions for each of the Office Finisher LX components and options are shown on the following page.
  • Page 5 Staple Cartridge Front Cover Interface Cover Hole Punch Waste Container Office Finisher LX - User Guide Use this attachment when unstapled A4 LEF, 8.5 x 11” LEF, or B5 LEF paper is output to the Office Finisher LX tray. Makes stapled copies or prints with a crease for easy manual folding.

  • Page 6: The Copy Output Screen

    2 Staples The Copy Output Screen The Copy Output screen allows you to sort copy Cancel Save outputs. If the optional Office Finisher LX has been Collation Collated installed, the stapling, hole-punching, and/or Uncollated creasing feature will also be available.

  • Page 7: Installing The Tray Attachment

    LEF paper is output to the Finisher tray, it is recommended to use the Tray Attachment. Remove the Tray Attachment from under the Office Finisher LX Tray. Attach the Tray Attachment to the tray, as shown. Office Finisher LX - User Guide...

  • Page 8: Loading Staples In The Automatic Stapler

    Loading Staples in the Automatic Stapler Loading Staples in the Automatic Stapler The optional Office Finisher LX contains an automatic stapler. When the finisher runs out of staples, a message appears on the touch screen. When this message is displayed, load a new staple case into the staple cartridge.
  • Page 9 Close the front cover of the finisher. NOTE: If the front cover is not completely closed, a message will appear and the machine will not operate. Office Finisher LX - User Guide...

  • Page 10: Loading Booklet Maker Staples

    Hold the tabs on both sides of the new booklet staple cartridge, and insert it into the original position until it clicks. NOTE: If you have trouble inserting the cartridge, make sure that the staples in the cartridge are properly in place. Office Finisher LX - User Guide...
  • Page 11 Repeat steps 2 and 3 to replace the other booklet staple cartridge. Close the side cover of the Booklet Maker. NOTE: If the side cover is not completely closed, a message will appear and the machine will not operate. Office Finisher LX - User Guide...

  • Page 12: Clearing Staple Jams

    Hold the staple cartridge by Lever R1, and slide the cartridge to the right. Hold the staple cartridge by the orange lever, and lift up to remove the cartridge. Check the inside of the Office Finisher LX for any remaining staples. 1-10 Office Finisher LX - User Guide...
  • Page 13 Hold the staple cartridge by the orange lever, and return the cartridge to its original position. Close the front cover of the Office Finisher LX. If the staples cannot be removed after carrying out the above procedures, contact the Xerox Welcome Center.
  • Page 14 Booklet Maker. Repeat the step above for the other Booklet Maker Stapler Cartridge. Check the inside of the Office Finisher LX for any remaining staples. 1-12 Office Finisher LX - User Guide...
  • Page 15 Repeat the step above for the other Booklet Maker Stapler Cartridge. NOTE: If you have trouble inserting the cartridge, make sure that the staples in the cartridge are properly in place. Close the side cover of the Booklet Maker. Office Finisher LX - User Guide 1-13...

  • Page 16: Clearing Paper Jams

    Clearing Paper Jams Follow the steps below to clear paper jams in the optional Office Finisher LX. Office Finisher LX Top Cover Jams Open the Office Finisher LX Top Cover. Remove the jammed paper. Close the Office Finisher LX Top Cover. 1-14...
  • Page 17 Clearing Paper Jams Office Finisher LX Transport Cover F Jams Open the Office Finisher LX Transport Cover F. Remove the jammed paper. Close the Office Finisher LX Transport Cover F. Office Finisher LX - User Guide 1-15...
  • Page 18 Clearing Paper Jams Booklet Maker Paper Jams Make sure that the machine has stopped, and open the side cover of the finisher. Remove the jammed paper. Close the side cover of the Booklet Maker. 1-16 Office Finisher LX - User Guide...

  • Page 19: Emptying The Hole Punch Waste Container

    Office Finisher LX - User Guide Emptying the Hole Punch Waste Container Emptying the Hole Punch Waste Container NOTE: Leave the power on when emptying the Hole Punch Waste Container. If the power is turned off, the machine will not recognize that the waste container has been emptied.

Table of Contents