Summary of Contents for Windsor Saber Cutter SCEX264
Page 1
WALK BEHIND SCRUBBER Operating Instructions (ENG) Bedienungsanleitung (GER) Istruzioni operative (ITA) Instrucciones de funcionamiento (SPA) Manuel d’utilisation (FRE) MODELS: SCEX264 SCEOX264 10052320 10052290 SCEX324 SCEOX324 10052330 10052300 IPX4 Read these instructions before using the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen Leggere attentamente queste istruzioni prima di azionare la macchina Lea las instrucciones antes de utilizar la máquina...
Page 2
Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
TABLE OF CONTENTS Machine Data Log/Overview......2 Vacuum Motors..........4-11 Table of Contents..........3 Actuator Scrub Deck........4-12 Greasing Axles ..........4-13 HOW TO USE THIS MANUAL Machine Troubleshooting ......4-14 How to use this Manual.........1-1 GROUP PARTS LIST SAFETY Control Handle..........5-1 Cover (Front) &...
They are Parts may be ordered from authorized Windsor listed in this general order: dealers. When placing an order for parts, the machine model and machine serial number are Batteries important.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. WARNING: To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual.
WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use Windsor approved replacement parts. WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep top cover in raised position when charging.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PRV NO. 81494 BATTERY CAUTION 86252520 PRV NO. 80885 CIRCUIT BREAKER DECAL 86243530 PRV NO.
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY Nominal power 1450 W Rated Voltage 24VDC Rated Amperage 60 Amps Batteries 4 X 6 Volt 250-305-335AH @ 20 hr rate Scrub Brush Motors 2 X .75 hp (0.56 kW) Vacuum Motor .75 hp (0.56 Kw) Propelling Motor .3 hp (0.22 Kw) Mass (GVW)
Page 9
TECHNICAL SPECIFICATIONS ITEM MEASURE Height 45 in. (114 cm) Length with 26 in. (66 cm) scrub head 64 in. (163 cm) Length with 32 in. (81 cm) scrub head 66 in. (167 cm) Width without squeegee and scrub head 24 in. (61 cm) Width of squeegee for 26 in.
HOW THE MACHINE WORKS The function of the recovery system is to vacuum The Saber Cutter is a battery powered, self- the soiled water back into the recovery tank. The propelled, hard floor scrubber intended for recovery system consists of the squeegee, commercial use.
Page 13
CONTROLS 1. Key Switch 9. Vacuum Switch 2. Emergency Shut Off Switch 10. Squeegee Lift Lever 3. Speed Control Knob 11. Squeegee Pitch Adjustment Knob 4. Propel Control Lever 12. Squeegee Deflection Adjustment Knobs 5. Reverse Button 13. Battery Charge Level Indicator 6.
Page 14
CONTROLS 7. ACTUATOR SWITCH 10. SQUEEGEE LIFT LEVER Adjusts the amount of brush pressure to the Raises and lowers the squeegee. floor by raising or lowering the scrub deck. To lower the squeegee, lift the lever from its raised position. To increase brush pressure, press the bottom of the switch.
Page 15
CONTROLS 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries.
MACHINE OPERATION FILLING SOLUTION TANK PRE-RUN MACHINE INSPECTION FOR SAFETY: Before leaving or servicing machine; Do a pre-run inspection to find possible problems that stop on level surface, turn off machine and remove could cause poor performance or lost time from key.
MACHINE OPERATION NORMAL SCRUBBING TO BEGIN SCRUBBING Plan the scrubbing pattern in advance. The WARNING longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs When operating the machine around people, pay close attention for unexpected movement. Use should be the longest possible without turning, extra caution around children.
MACHINE OPERATION RECOVERY TANK DOUBLE SCRUB 1. Unhook the large drain hose from the retainer. For floors which are heavily soiled or have thick Unscrew the T-handle on plug enough to loosen accumulations of floor finish may not clean plug, then lower hose in direction of the drain. sufficiently with one pass.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY ANNUALLY Check battery acid level Before Check vac hose connections starting Clean the squeegee blades the work Inspect brushes or pads for debris: period wire string, wear Inspect vac fan shut off float screen Drain &...
MAINTENANCE 1. BATTERIES The batteries provide the power to operate the CAUTION machine. The batteries require regular maintenance When servicing machine, avoid contact with to keep them operating at peak efficiency. battery acid. The machine batteries will hold their charge for long WARNING periods of time, but they can only be charged a Batteries emit hydrogen gas.
MAINTENANCE TO CHARGE THE BATTERIES CHECKING BATTERY SPECIFIC GRAVITY WARNING Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. CAUTION Batteries emit hydrogen gas. Explosion or fire Battery Check can result. Keep sparks and open flame away. Keep covers open when charging.
MAINTENANCE 5. Replace the battery caps, and leave them in CHANGING BATTERIES place while charging. Stop the machine in a clean area next to the 6. Unplug the battery connector from the machine. charger. Turn off machine. FOR SAFETY: When charging, connect the FOR SAFETY: Before leaving or servicing the charger to the batteries before connecting the machine;...
MAINTENANCE 2. SQUEEGEE BLADES TO REMOVE SQUEEGEE ASSEMBLY The front squeegee blade allows solution to pass 1. With the squeegee in the up position, turn key through channels in the blade into the squeegee switch “OFF”. assembly while maintaining vacuum to provide lift. 2.
MAINTENANCE TO ADJUST SQUEEGEE PITCH TO ADJUST AMOUNT OF REAR 1. Choose a smooth, level surface. Turn “ON” the SQUEEGEE DEFLECTION key switch. Lower the squeegee and drive 1. Choose a smooth, level surface. Lower the forward at least 2 feet (60cm.). squeegee and drive forward at least 2 feet 2.
MAINTENANCE SCRUB BRUSHES REPLACING OR INSTALLING SCRUB There are four different types of brushes available to BRUSHES cover applications from cleaning heavily soiled floors 1. With the scrub deck up, turn “OFF” the machine. to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE 6. SOLUTION STRAINER BRUSH MOTOR CARBON BRUSH The solution strainer is located in front of the left REPLACEMENT front wheel. The solution strainer protects the 1. Scribe alignment mark on motor barrel to motor solenoid valve from debris. If there is little or no cap.
MAINTENANCE 8. TRACTION MOTOR 9. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in WARNING the event of an electrical overload. When a Do not use a pressure washer to clean around the circuit breaker is tripped, reset it by pressing motors.
5. Remove vacuum motor and mounting bracket 5. Remove vacuum motor and mounting bracket assembly. assembly. 6. Reverse steps to install 6. Reverse steps to install Note: Vacuum Motor Carbon Brushes Replacement (Windsor) Place End Cap stop in groove. Carbon Brushes...
MAINTENANCE 12. ACTUATOR SCRUB DECK SCRUB DECK ACTUATOR ADJUSTMENT REMOVAL/REPLACEMENT The actuator will need to be adjusted when replaced. FOR SAFETY: Before leaving or servicing To adjust the actuator: machine, stop on a level surface, turn off machine and set parking brake (If option is 1.
Page 31
MAINTENANCE RECOMMENDED GREASING: 1-2 strokes of Mobiltemp®78 or compatible clay-based or calcium-based grease. 4-13 CUTTER 24V (SCE) 86037020 04/04/07...
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeegee blades Rotate or replace squeegee blades Vacuum hose clogged Clear obstruction from hose Vacuum hose disconnected Reconnect vacuum hose from squeegee or recovery tank...
Page 33
MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or Turn on or increase flow set too low setting Solution strainer plugged Clean solution strainer Solution hoses obstructed Clear obstruction from hose Solution solenoid valve Clean or replace...
COVER (FRONT) & TANK MOUNT CUTTER 24V (SCE) 86037020 04/04/07...
Page 37
COVER (FRONT) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86070150 140574 BRKT, TANK MOUNT 24V 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS 86062530 27925 COVER, FRONT, 24V GRY 86004790 48012 KNOB, 5/16 –18 4 PRONG...
COVER (TOP) & TANK MOUNT CUTTER 24V (SCE) 86037020 04/12/07...
Page 39
COVER (TOP) & TANK MOUNT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86062540 27926 COVER, TOP 24V GRY 86271840 57285 NUT, 5/16-18 HEX NYLOCK THIN SS 86010670 87029 WASHER, 5/16 FLAT SS 86239630 41429 HINGE, COVER TO TANK 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS...
Page 53
SCRUB DECK AQUA-MIZER-26IN SCRUBHEAD SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO...
Page 55
SCRUB DECK AQUA-MIZER-32IN SCRUBHEAD SERIAL NO. PART NO. PRV. NO DESCRIPTION FROM NOTES: 86006930 70514 SCR, 5/16-18 X 1.00 BSHCS SS 86228840 09124 BEARING, FLANGED .314 ID X .502 OD 86259420 87232 WASHER, THRUST .51 ID X 1 OD BRO 86259400 87205 WASHER, THRUST .51 ID X 1 OD BRO...
Page 63
SCRUB DECK LIFT LINKAGE-26IN SCRUBDECK SERIAL NO. PART NO. PRV. NO DESCRIPTION FROM NOTES: 86273780 70015 SCR, 1/4-20 X 3/4 HHCS SS NP 86069910 140545 BRACKET, ANGLE SUPPORT LEFT 86273740 70010 SCR, 1/4-20 X 1.5 HHCS SS 86010630 87013 WASHER, 1/4ID X 5/8OD SS 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS...
Page 69
SCRUB DECK LIFT SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86276920 70755 SCR, 3/8-16 X 1HHCS SS NP 86279590 87185 WASHER, 3/8 SEALING X 3/4 OD WAS 87003 86069590 140479 BRACKET, ACTUATOR MOUNT BACK 86069600 140480 BRACKET, ACTUATOR MOUNT FRONT 86272410 66233 PIN, CLEVIS 3/8”...
Page 85
WIRING-BATTERY SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86010120 82803 CONNECTOR 175 DCA, RED W/O TERMS 86271870 57290 NUT, 1/4-20 HEX NYLOCK THIN SS NOT SHOWN 86002510 23125 CABLE ASM, BAT. JUMPER X 15” NOT SHOWN 86002570 23190 WIRE, 4 X 27 RD B CLAMP X C TERM NOT SHOWN 86002580...
WIRING-CONTROL PANEL DIAGRAM B DIAGRAM A 51 RED 30 RED 49 BLK 56 RED 18 BLU 48 BLK 47 RED 52 RED 41 BLU 29 YLW 50 BLK 43 BLK 63 BLK 62 RED 63 BLK 26 RED 61 BLK 33 RED 2/25 BLK 26 RED...
Page 87
WIRING-CONTROL PANEL SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86239000 41443 HARNESS, PANEL BASIC 86261210 29204 DIODE ASM, 76008 X 76008 86003410 29215 DIODE ASM, 76075 X 76075 86267340 880269 WIRE, 22” RED/18 76040 X 76075 86269300 88868 WIRE, 16”...
WIRING-MAIN HARNESS 74 RED RIGHT BRUSH MOTOR 75 BLK 76 RED LEFT BRUSH MOTOR 77 BLK 72 RED MOTOR 73 BLK 5 BRN DIAGRAM A 6 BLK ACTUATOR 75 BLK 78 RED 79 BLK 76 RED 69 RED 77 BLK 74 RED 68 GRN/YLW SOLENOID...
Page 89
WIRING-MAIN HARNESS SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86238980 41441 HARNESS, MAIN 5-56 CUTTER 24V (SCE) 86037020 04/04/07...
Page 93
BRAKE SERIAL NO. PART NO. PRV NO. DESCRIPTION NOTES: FROM 86248370 66381 PAD, BRAKE 86006220 66192 PIN, ROLL 1/4 X 1.25L 86252070 67486 ROD, BRAKE 24V 86231330 14664 BUSH, BRZ FLG .63 X .75 X 1.0 86255060 73426 SPRING, EXT .43D X 2.50 L X .047 W 86070070 140565 BRKT, LOWER BRAKE MOUNT 24V...
ACCESSORY PUMP-OPTION SOLUTION RECOVERY BRACKET TO COUPLING TO FILTER (EXISTING HOSE) 5-63 CUTTER 24V (SCE) 86037020 04/04/07...
Page 97
ACCESSORY PUMP-OPTION SERIAL NO. PART NO. PRV NO. DESCRIPTION FROM NOTES: 86010670 87029 WASHER, 5/16 FLAT SS 86276780 70728 SCR, 5/16-18 X 3/4 HHCS SS 86233150 20042 CLAMP, 3/8 HOSE (D-SLOT) 86070140 140573 BRKT, FILTER/SOLENOID MOUNT 86240410 40078 HOSEBARB, 1/2 TEE 86282200 39617 HOSE 3/8 ID X 40”...