Battery Saver Mode; Option Select Mode - Whistler 1788 Owner's Manual

OPERATION
Engaging/Disengaging VG-2
See Option Select Mode to turn this feature
on/off. When a VG-2 signal is detected, the VG-2
alert is sounded and the display flashes "VG-2".
After 3 seconds the audio is canceled and the
display no longer flashes. This cycle is repeated
if the VG-2 signal is again detected.
During the period a VG-2 signal is detected, a
radar signal cannot be detected. However,
because the VG-2 alert has confirmed that a
patrol car is nearby, you are already aware of the
potential for speed monitoring and can adjust
your speed accordingly. Laser detection is not
affected while a VG-2 signal is detected.

Battery Saver Mode

The Vehicle Battery Saver Mode automatically
shuts off the detector if you forget to turn it off.
The timer is reset if the detector is turned off, the
optional power cord is unplugged or any button is
pressed before the timer has expired. The detec-
tor will alert you with an audible and visual warn-
ing before it shuts off. This auto off function can
be programmed for the following: Off, 1, 2, or 3
hours.
During this warning you can reset the timer by
pressing any button.
If the unit has automatically turned itself off, press the
Power button to turn the unit back on. You can man-
ually engage the Battery Saver Mode by pressing
and holding the City button until one beep is
heard.
Refer to "Option Select Mode" for instructions for
changing the Battery Saver Mode settings.
11
OPERATION

Option Select Mode

Entering Option Select Mode allows you to customize
options such as Tone Select, Abbreviated Power Up
Sequence and VG-2 Mode. Press and hold quiet but-
ton to enter Option Select Mode. When selecting
options, the volume up , volume down
Quiet buttons must be pressed within 20 seconds or
options mode will automatically be exited. To enter:
Press: Display To Change: Option:
Quiet Reads:
1st Time TONE 3 = YES Tone 1, 2, 3
= NO (3 different X, K,
Ka Patterns)
2nd Time TEST YES = ON X, K, Ka Audio
= OFF tones 1 beep
during Power Up
3rd Time X-ON = ON X Band On
= OFF X Band Off
4th Time K-ON = ON K Band On
= OFF K Band Off
5th Time Ka-ON = ON Ka Band On
= OFF Ka Band off
6th Time LASER ON = ON LASER Band On
= OFF LASER Band Off
7th Time VG-2 OFF = ON Turns VG-2 On
= OFF Turns VG-2 Off
8th Time SR OFF = ON Safety Radar On
= OFF Safety Radar Off
9th Time POP ON = ON Pop On
= OFF Pop Off
10th Time B SVR 1 HR OR Options are 1H,
2H, 3H & NO
12
OPERATION
Stay Alert Feature
The Stay Alert Feature is designed to test a driver's
alertness. To engage (when unit is not alarming) :
• Press and hold City for approximately 2 sec-
onds. Release button during or immediately after
or
the alert is given. Display shows:
Within 30-60 seconds two beeps are sounded;
to show alertness, the driver must press either the
City, Volume, or Quiet buttons within 3-5 seconds. If
a button is pressed within 3-5 seconds, the cycle is
repeated.
If a button was not pressed within 3-5 seconds
alarm sounds and the display shows:
• Press Power to exit.
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT oper-
ate a vehicle if you are drowsy. During extended
periods of vehicle operation, you should take fre-
quent breaks. Improper reliance on the Stay Alert
feature may result in vehicle damage, personal
injury or death. NEVER OPERATE A VEHICLE IF
YOU ARE DROWSY.
SWS
™
Safety Warning System
In communities where transmitters are located,
the Safety Warning System ™ displays over 60
text messages. When Safety Radar is detected
the audio alert is geiger counter-like.
N N o o t t e e : : Safety Warning System
™
in Option Select Mode.
Safety Warning System Text
Example: Poor - Road - Surface.
Note: Not all areas have Safety Warning System
transmitters.
13
™
is labeled "SR"
™