Page 1
InstructionS WHIRLPOOL UNDERCOUNTER WATER FILTRATION SYSTEMS I, II, & Ill...
Page 2
Materials Needed for Optional Sink Faucet Installation Sink faucet, Part No. 4319154, available from your Whirlpool dealer. Includes: faucet base with blue tubing attached, assembly hardware, faucet spout, 2-way grey connector with push-in ends, and a “T” grey connector with push-in ends,...
Refer to the Use & Care information at the end of this booklet. If you need more help, the Whirlpool Consumer Assistance Center will answer any questions you may have about operating or maintaining your water filtration system. The Whirlpool Consumer Assistance Center is open 24 hours a day, 7 days a week.
Page 4
Instructions At A Glance 1. Turn off cold water supply. (St; la-lb) 3. Connect saddle valve to cold water supply. Turn saddle valve handle clockwise until piercing lance enters pipe and stops. (Steps lc-lg or 1 h-l j) For detailed instructions see following page. Electrical Shock Hazard Special...
Page 5
Product Damage DO NOT connect to a hot water supply line. Failure to follow this instruction could result in product damage. Take note of water requirements listed under . the Use & Care section of this booklet. The filtration system’s feed line (orange tubing) connects to your cold water supply line using the saddle valve.
Page 6
Instructions At A Glance For detailed instructions see following page. 1. Decide if the system will be connected to your refrrgerator, to an optional faucet or to both. (Step 2a) 2. Connect refrigerator’s water supply to filtration assembly with blue tubing. (Steps 2b-2c) 3.
Page 7
If you choose to connect filtration system to a sink faucet, order sink faucet, Part No. 4319154, available from your Whirlpool dealer. This kit includes: faucet assembly with blue tubing attached, assembly hard- ware, faucet spout, 2-way grey c6nnectoi with push-in ends, and a ‘7”...
Page 8
Start Up Instructions At A Glance For detailed instructions see following page. 1. Slide filtration assembly onto mounting screws. 2. Turn on cold water supply. (Step 3d) (Steps 3a-3c) 3. If filtration assembly was connected to refrigerator, make and discard 2 batches of ice and drain 4.
Additional tubing may be required and is available from your local plumbing distributor or from your Whirlpool dealer. Continue with step 3b. Drill pilot holes for the mounting bracket at . the locations you’ve marked. Insert mountin! bracket screws in holes and tighten, leaving a slight gap between screw head and wall.
Water Requirements The filtration system must be connected to a cold water supply line providing 30-l 00 psi water pressure. The water temperature must be between 40”-100°F. Community or private well water must be potable (suitable for drinking). Personal Injury Hazard DO NOT use water filtration system if water is...
Page 11
Center telephone number, l-800-253-1 301. A special operator will tell you the name and number of your nearest Whirlpool-authorized service company. Maintain the quality built into your Whirlpool appliance - call a Whirlpool-authorized service company. WATER FILTRATION MODEL NO. WSClOOYW...
This product has been tested and listed by NSF International Standard 42 for Taste, Odor and Chlorine reduction (Class I) and Particulate reduction (Class II). Whirlpool Water Filtration System I Model No. WSClOOYW SPECIFICATIONS: Taste/Odor/Chlorine reduction (Class I) SERVICE FLOW RATE: 0.6 GPM (2.2 L/&n) @ 60 psi...
The performance the water being treated and the particular application Requirements” Whirlpool shall not be Ilable for lncldental or consequential damages. the exclusion or limitation of incidental or consequential not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from 13, 1965.
Page 14
Whirlpool Corporation Part No. 4373576 Printed on Recycled Paper in U.S.A. Benton Harbor. Ml 49022 01993 Whirlpool Corporation...