Error Messages - Panasonic DMR-HS2 Operating Instructions Manual

Error messages

On the television
No disc.
This is non-recordable disc.
This disc is not formatted
properly.
Please format the disc in
'DISC SETTING' to record.
This disc cannot be read.
Please check write protect
tab on the disc.
Contents of this disc are
protected.
Cannot finish recording
completely.
Cannot record.
HDD is full.
Disc is full.
Cannot dub from this disc.
Please set clock.
This disc may not be played
in your region.
Your selection exceeds the
recorder's rating limit.
Cannot play back on this unit. ≥You tried to playback incompatible pictures (TIFF images and MOTION JPEG cannot be played back).
No PC CARD
No valid PC card
No DVD-RAM disc
Please check write protect
tab.
No folder
Cannot write.
Finalizing is necessary for
compatible playback.
On the unit's display
U11
NO DISC
U14
!?
U99
CHK REMOTE
RECOVER
≥You haven't inserted a disc. Correctly insert a disc that this unit can use.
≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.
≥The unit cannot record on the disc you inserted. The unit cannot record onto finalized DVD-R,
DVD-Video, CDs, or video CDs. Insert a DVD-RAM or unfinalized DVD-R.
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.
≥You inserted an incompatible disc. Insert a compatible disc.
≥The write-protect tab on the cartridge is set to PROTECT.
Use a ballpoint pen or similar to release the write protection.
≥The program is write-protected. Cancel the protection with the Direct Navigator.
≥The disc is write-protected. Cancel Disc Protection with DISC SETTING.
≥The program was copy-guarded.
≥No space left on HDD, DVD-RAM or DVD-R.
≥The connection from the external device (DV equipment etc.) was lost during recording.
≥Recording was not completed for some other reason.
≥The disc is scratched. Use another disc.
≥The disc is dirty.
≥You inserted an incompatible disc. Insert a compatible disc.
≥No space left on HDD, DVD-RAM or DVD-R.
Create space by erasing any unwanted programs. [HDD] [RAM]
Use a new disc. [RAM] [DVD-R]
Erase any unwanted files (still pictures).
≥You may record up to 300 folders and 3000 files (still pictures) using this unit.
≥Dubbing prohibited disc in tray.
≥The clock is not set. Set the clock.
≥You tried to play a disc with a region number different from this unit's region number. This unit can
only play discs with the region numbers compatible with this unit (1, All, or including the number 1).
≥A ratings level has been set for DVD-Video with this unit.
Unlock the unit with "Ratings" in "Disc" in the SETUP menu.
≥The PC card is not inserted. If this message is displayed with a compatible PC card already
inserted, turn off the power, remove and then re-insert the card.
≥The PC card format does not match.
≥The PC card inserted is not compatible.
≥DVD-RAM is not loaded.
≥DVD-RAM is not formatted.
(Even if this message is displayed, it may sometimes be possible to playback moving picture parts.)
≥Release the protection on the PC card.
≥Release the protection on the DVD-RAM.
≥There is no compatible folder in this unit.
≥The PC card is currently protected
≥There is no space remaining.
≥To enable playback of your DVD-R on compatible equipment, it is necessary to finalize it.
≥The disc is dirty or badly scratched.
– Clean the disc if it is dirty.
– The disc cannot be played if it is scratched and this display doesn't disappear.
≥You have inserted a disc the unit cannot play or record on.
– Insert a disc the unit can play or record on.
≥Cleaning has been carried out using DVD-RAM/PD lens cleaner.
Cleaning is finished. Press [< OPEN/CLOSE] and remove the disc cleaner from the disc tray.
≥The unit is hot.
– The unit switches to standby automatically for safety reasons and you cannot operate it. Wait for
about 30 minutes for the service number to disappear.
– Select a position with good ventilation when installing the unit.
– Do not block the cooling fan on the rear of the unit.
≥The unit fails to operate properly.
– Press [Í, DVD POWER] to switch the unit to standby. Now press [Í, DVD POWER] again to turn
the unit on.
≥The remote control and main unit are using different codes.
– Change the code on the remote control or main unit.
≥If there is a power failure or the AC plug was disconnected while the power was on.
The unit is carrying out its recovery process. Wait until the message disappears.
Dubbing to the HDD is not possible.
Release the write protection.
Erase any unwanted files (still pictures).
Page
8
18
8
38
8
—
PROTECT
40
38
—
—
—
—
—
10
8
38, 40
—
48
—
—
64
Cover
page
62
9
25
9
9
—
38
9
8, 38
9
9
48
38
10
8
—
—
—
—
—
65
—
67
RQT6570