Advertisement
Table of Contents
Model No. WESY92190
Serial No.
The serial number is found in the
location shown below. Write the
serial number in the space above.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
¨
USERÕS MANUAL
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Patent Pending
Advertisement
Table of Contents
Related Manuals for Weider WESY92190
Summary of Contents for Weider WESY92190
- Page 1 Model No. WESY92190 Serial No. The serial number is found in the location shown below. Write the serial number in the space above. Serial Number Decal QUESTIONS? As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you...
-
Page 2: Table Of Contents
Table of Contents Important Precautions ..............3 Before You Begin . -
Page 3: Important Precautions
Important Precautions To reduce the risk of serious injury, read the following important precau- WARNING: tions before using the weight system. 1. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. -
Page 4: Before You Begin
(excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY92190. The serial number can be found on a decal attached to the E2000 (see the front cover of this manual). -
Page 5: Assembly
Assembly Note: This introduction will save you more time than it takes to read it! Making Things Easier for Yourself Everything in this manual is designed to ensure that the weight system can be assembled suc- cessfully by anyone. However, it is important to recognize that the weight system is a sophisti- cated product with many small parts. -
Page 6: Frame Assembly
Frame Assembly 1. Before beginning assembly, make sure you have read and understood the information on page 5. Open the parts bag labeled ÒFRAME ASSEMBLY.Ó Press a 2Ó Square Outer Cap (51) onto each end of the Stabilizer (5). Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up through the Stabilizer (5) and place it flat on the floor. - Page 7 4. Press a 2Ó Square Inner Cap (21) into each end of the crossbar on the Top Frame (1). Slide two 5/16Ó Flat Washers (56) onto two 5/16Ó x 2 3/4Ó Bolts (67). Place the Top Frame (1) on top of the Front Upright (42) and align the indicated holes with the holes in the bracket on the Front Upright.
-
Page 8: Arm Assembly
8. Attach the indicated end of the Console Cord (83) to the indicated end of the wire bundle. Make sure that the Console Cord is attached exactly as shown. 9. Feed both Wire Ties (23) into the Wire Tie Blocks (82) that are pre-assembled to the Base (8). - Page 9 12. Note: In the following steps, some parts are not shown for clarity. Press a 2Ó Square Inner Cap (21) into the top of a Press Arm (46). Press a 1Ó Round Inner Cap (49) into the indicated hole in the Press Arm (46). Attach the Press Arm (46) to the Press Frame (12) with two 5/16Ó...
-
Page 10: Cable Assembly
Cable Assembly 15. Open the parts bag labeled ÒCABLE ASSEMBLY AND PULLEYS.Ó For Cable identification and rout- ing during steps 15Ð30, refer to the Cable Diagram and Cable ID Chart on page 19. Identify the High Cable (2). It is approximately 163 1/2Ó... - Page 11 18. Move to the other side of the unit. Wrap the High Cable (2) around a ÒVÓ-Pulley (6) in the direction shown. Attach the ÒVÓ-Pulley (6) and a Long Cable Trap (50) to the Right Butterfly Arm (48) with a 3/8Ó x 2 1/2Ó Bolt (96) and a 3/8Ó...
- Page 12 22. Remove the 3 1/2Ó Pulley (35) from the pre-assem- bled Adjustment Bracket (84). Wrap the High Cable (2) around the Pulley in the direction shown. Attach the Pulley to the Bracket with a 3/8Ó x 1 1/2Ó Bolt (60) and a 3/8Ó...
- Page 13 26. Move to the other side of the unit. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (19), a Cable Trap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó...
-
Page 14: Seat Assembly
30. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley to the Front Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (19), a Cable Trap (66), a 3/8Ó Flat Washer (55), and a 3/8Ó Nylon Jamnut (63). - Page 15 33. Press two 3/4Ó Round Inner Caps (34) into each Pad Tube (28). Insert one Pad Tube (28) into the Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad Tube. Insert the other Pad Tube (28) into the Leg Lever (29).
- Page 16 37. Plug one end of the Power Adapter Cord (64) into the indicated end of the wire bundle. Plug the other end into an outlet. WARNING: Keep hands and fingers clear of mov- ing parts. 38a.The following instructions are critical to the cor- rect operation of your weight system.
- Page 17 38d.Set the console to 150 pounds as shown in the inset drawing. This will begin to move the Weight Mechanism (26) down. 38e.See the inset drawing. Loosen the 3/8Ó Plain Nuts (85), and the 3/8Ó x 3Ó Bolt (88) so that the 3/8Ó x 4Ó Tap Screw (86) can rotate freely.
- Page 18 39. Note: The console cord should be positioned between the two bottom screws on the Shroud. Align the Right Shroud (79) with the holes in the Top Frame (1), the Base (8), and the two Uprights (18, 42 [not shown]) and attach it with 14 #8 x 3/4Ó...
-
Page 19: Cable Diagram
Cable Diagram The Cable Diagram below shows the proper routing of the High Cable (2) and the Low Cable (9). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly, that the Pulleys move smoothly, and that the Cable Traps do not touch or bind the Cables. -
Page 20: How To Use The Weight System
How to Use the Weight System The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise posterS on the shroud and accompanying this manual to see how the weight system should be set up for each exercise. - Page 21 USING THE CURL POST Some exercises require that the Curl Post (10) be removed. To remove the Curl Post, loosen the 5/16Ó x 2Ó Knob (72). Slide the Curl Post off of the Seat Frame (36). To reattach the Curl Post (10), slide the Curl Post onto the Seat Frame (36) so each of the welded brackets is between the Seat Frame and the bracket on the Leg lever (29).
-
Page 22: Trouble-Shooting And Maintenance
Trouble-shooting and Maintenance Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use sol- vents. Note: If any of the following adjustments are made to the weight system, the weight mechanism must also be adjusted. - Page 23 1" Round Inner Cap (49) 1" Round Cover Cap (3) 3/4" Round Inner Cap (34) 3/8" x 2 1/4" Eyebolt (44) 1 1/2" Square Inner Cap (33) 2" Square Outer Cap (51) 1" x 2Ó Inner Cap (11) 2" Square Inner Cap (21)
- Page 24 Part Identification ChartÑWESY92190 R1299A 5/16" Nylon Locknut (53) 1/4" x 3/4" Screw (17) 5/16" Nylon Jamnut (91) 5/16" x 1 3/4" Bolt (58) 3/8" Plain Nut (85) 1/4" x 2" Carriage Bolt (38) 3/8" Nylon Jamnut (63) 1/4" x 2" Bolt (71) 3/8"...
- Page 25 1/4" Flat Washer (90) 1/4" Nylon Locknut (89) 1" Retainer (4) 3/8" x 1 3/4" Bolt (60) 3/8" x 2 1/4" Bolt (65) 3/8" x 2 1/2" Bolt (96) Cable Clip (73) 3/8" x 3Ó Bolt (88) 3/8" x 3 1/4" Bolt (69) #8 x 1/2"...
- Page 26 Part ListÑModel No. WESY92190 Key No. Qty. Description Top Frame High Cable 1Ó Round Cover Cap 1Ó Retainer Stabilizer ÒVÓ-Pulley Plastic Bushing Base Low Cable Curl Post 1Ó x 2Ó Inner Cap Press Frame Seat 5/16Ó x 2 3/4Ó Carriage Bolt...
- Page 27 Exploded DrawingÑModel No. WESY92190 R1299A...
-
Page 28: Ordering Replacement Parts
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 WEIDER is a registered trademark of ICON Health & Fitness, Inc. Part No. 160370 R1299A ¨...