Weider WESY38320 User Manual

Weider pro 3550 user's manual

Advertisement

Model No. WESY38320
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if parts are
missing, we will guarantee com-
plete satisfaction through assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our cus-
tomer hot line will provide imme-
diate assistance, free of charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
Patent Pending
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Visit our website at

Advertisement

Table of Contents
loading

Summary of Contents for Weider WESY38320

  • Page 1 Model No. WESY38320 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are...
  • Page 2: Table Of Contents

    Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before beginning assembly. WEIDER is a registered trademark of ICON Health & Fitness, Inc.
  • Page 3: Important Precautions

    IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
  • Page 4: Before You Begin

    (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is WESY38320. The serial number can be found on a decal attached to the weight system (see the front cover of this manual for the location of the decal).
  • Page 5: Assembly

    ASSEMBLY Make Assembly Easier Everything in this manual is designed to ensure that the weight system can be assem- bled successfully by anyone. Before beginning assembly, make sure to read the information on this page. This brief introduction will save you much more time than it takes to read it.
  • Page 6: Frame Assembly

    FRAME ASSEMBLY Make sure that you understand all of the information on page 5 before you begin assembling the weight system. Locate and open the parts bags labeled “FRAME ASSEMBLY 1” and “FRAME ASSEMBLY 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120).
  • Page 7 4. Press a 1 1/2” Square Inner Cap (67) into the square tube on the Butterfly Upright (3). Slide the Butterfly Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
  • Page 8 7. Press a 2” x 3” Inner Cap (58) into the top of the Squat Upright (4). Slide the Squat Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (110) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
  • Page 9 9. Insert the ends of two Weight Guides (42) into the indicated bracket on the Long Base (120). Attach the Weight Guides to the Long Base with a 3/8” x 6 1/2” Bolt (95) and a 3/8” Nylon Locknut (87). Attach the other two Weight Guides (42) to the Long Base (120) in the same way.
  • Page 10: Arm Assembly

    12. Press a 2” x 3” Inner Cap (58) into the Butterfly Top Frame (7). Attach the Butterfly Top Frame to the Top Frame (6) with two 5/16” x 2 3/4” Bolts (85), two 5/16” Washers (90), and two 5/16” Nylon Locknuts (86).
  • Page 11: Cable Assembly

    16. Lubricate a 3/8” x 3” Button Head Bolt (104) and both sides of two Plastic Washers (56) with grease. Attach the Right Butterfly Arm (26) to the Butterfly Frame (47) with the Bolt, the two Plastic Washers, two Butterfly Caps (57), two 3/8” Washers (91), and a 3/8”...
  • Page 12 20. Remove the preattached 3 1/2” Pulleys (78 [only one is shown]) from the Offset Double “U”- bracket (61). Wrap the VKR High Cable (74) under a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”-bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8”...
  • Page 13 24. Route the Lat Cable (88) over a 3 1/2” Pulley (78). Slide a Long Cable Trap (102) onto a 3/8” x 1 3/4” Bolt (93). Attach the Pulley to the indicated bracket on the Top Frame (6) with the Bolt and a 3/8” Nylon Locknut (87).
  • Page 14 28. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Attach the Pulley and a Long Cable Trap (102) to the indicated bracket on the Butterfly Upright (3) with a 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut (87).
  • Page 15 32. Locate the Leg Lever Cable (75), which is 88” long and has an eyelet on one end and a thread- ed pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the tab on the Leg Lever (10) with a 5/16”...
  • Page 16 36. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with a 1/4” Washer (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Nylon Locknut;...
  • Page 17 40. Wrap the VKR Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 41.
  • Page 18 44. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable Trap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87).
  • Page 19: Seat Assembly

    48. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated bracket on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 49. Wrap the Squat Cable (73) over a 4 1/2” Pulley (119).
  • Page 20 52. Press two 3/4” x 1 1/2” Inner Caps (116) and a 1 1/4” Square Inner Cap (117) into the Seat Bracket (11). Attach the Seat (16) to the Seat Bracket (11) with two 1/4” x 3/4” Screws (114), a 1/4” x 1 1/2” Screw (99), and a 1/4”...
  • Page 21 56. Attach the Squat Arm (32) to the Squat Bracket (37) with two 3/8” x 2 1/2” Carriage Bolts (106), two 3/8” Washers (91), and two 3/8” Nylon Locknuts (87). Do not tighten the Nylon Locknuts yet. Finish attaching the Squat Arm (32) to the Squat Bracket (37) with a 3/8”...
  • Page 22: Adjustments

    ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises. IMPOR- TANT: When attaching the lat bar, row bar, or handle, make sure that the attachments are in the correct starting position for the exercise to be performed.
  • Page 23 ADJUSTING THE SQUAT ARM, SEAT, OR BUTTERFLY BACKREST To adjust the height of the Squat Arm (32), first turn the Adjustment Handle (65) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position.
  • Page 24: Weight Resistance Chart

    WEIGHT RESISTANCE CHART The chart below shows the approximate weight resistance at each weight station. “Top” refers to the 10-pound top weight. The other numbers refer to the 10-pound weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differ- ences in individual weight plates as well as friction between the cables, pulleys, and weight guides.
  • Page 25: Troubleshooting

    TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used.
  • Page 26: Cable Diagrams

    CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables.
  • Page 27 Leg Lever Cable (75) VKR Low Cable (72)
  • Page 28 PART IDENTIFICATION CHART—Model No. WESY38320 1/2" Washer (1) 3/8" Washer (91) 5/16" Washer (90) 5/16" Lock Washer (115) 1/4" Washer (97) 1/2" Spacer (89) 3/4" Spacer (124) 1/2" Nut (118) 3/8" Nylon Locknut (87) 3/8" Nylon Jamnut (113) 5/16" Nylon Locknut (86) 1/4"...
  • Page 29 3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) 1/4" x 1 1/2" Bolt (99) 5/16" x 1" Shoulder Bolt (103) #10 x 1" Screw (14) 5/16" x 3/4" Button Head Screw (51) 1/4" x 3/4" Screw (114) #8 x 3/4"...
  • Page 30 1" Round Inner Cap (29) 1 1/2" x 2” Inner Cap (21 3/4” x 1 1/2" Inner Cap (116) 2" Square Inner Cap (105) 1 1/4" Square Inner Cap (117) 1 1/2" Square Inner Cap (67) 2" x 3” Inner Cap (58)
  • Page 31 PART LIST—Model No. WESY38320 No. Qty. Description 1/2” Washer Short Base Butterfly Upright Squat Upright VKR Upright Top Frame Butterfly Top Frame Seat Frame Seat Upright Leg Lever Seat Bracket Curl Frame Backrest Bracket #10 x 1” Screw Butterfly Backrest...
  • Page 32 EXPLODED DRAWING—Model No. WESY38320 R1102A...
  • Page 33: Ordering Replacement Parts

    Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre- pared to give the following information: • The MODEL NUMBER of the product (WESY38320) • The NAME of the product (WEIDER •...

This manual is also suitable for:

3550Wesy38322

Table of Contents