Page 1
ViewSonic by Premier Mounts INSTALLATION MANUAL WMK-005 UNIVERSAL PROJECTOR MOUNT Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com IN-WMK005.R3...
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Page - 4 - Warning Statements Contact Premier Mounts with any questions. WMK-005 Installation Manual...
WMK-005 Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
Page 6
Options 1 and 2. The number of legs may vary depending on the number of mounting points found on the bottom of the projector. Combination Option 2 Single Leg Page 6 WMK-005 Installation Manual...
WMK-005 Features Congratulations on your recent purchase of your WMK-005 universal projector ceiling/ wall mount kit. This unit is designed for projectors weighing 25lbs. (13kg) or less. The mount is easy to install and is loaded with additional installation features built into the mount. These features allow you to optimize the projector’s position to the screen for the best projector performance and picture quality.
Identify the number of mounting points and screw thread size. Most projectors have either three or four mounting points and are M4, M5 or M6 in thread size (Figure 1). Mounting Points Blanket/ Soft Cloth Page 8 Figure 1. Projector Preparation WMK-005 Inverted Projector Flat Surface Installation Manual...
Page 9
WMK-005 Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points (Figure 2A and Figure 2B). Loosen the security screw knurl knob far enough to allow the two parts to be rotated 180° apart and separate (Figure 2C).
Two Piece Leg M5 Allen Wrench M6 x 12mm Hex Head Screw M5 x 12mm Hex Head Screws M4 x 12mm Hex Head Screws Page 10 Figure 3. Bracket Installation One Piece Leg Inverted Projector Universal Mount Leveling Barrels Installation Manual WMK-005...
WMK-005 Leveling the Mounting Bracket CAUTION: Secure but do not over tighten the mounting hardware. Failure to do so will result in damaging the threads in the projector. Rotate the leveling barrels to level the mounting bracket. Position the mounting bracket so that it avoids most, if not all, ventilation points (including lamp and filter access doors).
(supplied) or with other (commercially available) hardware depending on your installation environment (Figure 5). Ceiling Structure Wood Screws Upper Assembly Figure 5. Securing the Upper Assembly Ceiling Plate Page - 12 - Wooden Ceiling Stud Secure the ceiling mount to the center of the wooden stud. Knurl Knobs Installation Manual WMK-005...
WMK-005 Low Profile Installation OPTIONAL If your installation requires the overall height of the mount to be less that the approximate 9” shown with the standard mount assembly, you can convert the height to only 2 ½” by simply removing the adjustment channel as shown.
Page 14
Do not use the star washers on a close- ceiling application Page - 14 - Secure the ceiling plate to the ceiling structure. Figure 6B. Low Profile Installation WMK-005 Wooden Stud Lag Bolts Allen Wrench Secure the bell housing with two M8 x 16mm screws and flat washers.
WMK-005 Securing the Projector to the Upper Assembly Make sure the three-knurl knobs are loosened to fully expose to the “tri-lock” mounting plate in the base of the upper assembly. Carefully lift the projector and insert the mounting bracket mating special tri-lock cutout into the mating portion of the upper assembly.
WMK-005 Plastic Cap Installation Once all the final adjustments have been finished, install the plastic caps on the leveling barrels (Figure 9). Installation Manual Figure 9. Plastic Cap Installation Page - 17 -...
There may be several mounting positions for your particular bracket. Try to line up the holes on the bracket with the mounting points on the projector. If this still does not solve the problem, then contact Customer Service and advise them of the situation. Page - 18 - WMK-005 Installation Manual...
WMK-005 Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury.