Universal Remote Control CLIKR-5 UR5L-8520L Operating Instructions

1 Introduction
Operating Instructions For
CLIKR TM -5
The UR5L-8520 is designed to
CLIKR ™ -5
operate all Scientific-Atlanta, Pioneer
Voyager and Pace Micro digital set top
boxes (including DVR & HD), plus the
Cable Remote Control
majority of TV, VCR, DVD and AUDIO
equipment on the market as shown below.
CABLE : Cable Converters
UR5L-8520L
VCR : VCRs and TV/VCRs
AUX : Audio Receivers and DVRs, etc.
2 Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3 Operations
DEFAULT STATE:
Component Default: CABLE
Channel Default: CABLE channel and
numbers operate through the CABLE. You
have the option of controlling channel and
numbers through the TV, VCR or DVD. Refer
to section I for programming steps.
Volume Default: CABLE volume and mute
operate through the TV. You have the option
Universal Remote Control, Inc.
of controlling volume and mute through the
www.universalremote.com Cable box, VCR or DVD. Refer to section J J
OCE-0045K REV 03(04/14/07) for programming steps.
4 Button Functions
TV : Televisions
DVD: DVD Players
5 Programming the Remote Control
There are three ways you can program your CLIKR TM -5 remote:
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method * The Learning Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers
that correspond to a particular Component's manufacturer/brand, so it's the fastest and easiest of the three
methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all
the codes in the remote control, one at a time. The Learning Method allows you to transfer functions from other
remotes, one button at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light for 30 seconds.If
you do not press a button within 30 seconds, the LED light will turn off and exit setup mode and you will need to
start over.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and [OK/SEL] button
simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is
ready to be programmed.
STEP3 Point the remote control toward the STEP2 Line up the CLIKR TM -5 to the other remote,
Component and enter the 3-digit code head-to-head, 1 or 2 inches apart.
number assigned to your brand.
STEP3 Press any button on the CLIKR
*Note : If the 3-digit code number you just entered is
want to teach a command to. For example,
correct, the Component will turn Off. If it did not
if you want to teach the [MUTE] button,
turn Off, continue entering code numbers listed press the [MUTE] button.
for that brand until the Component turns Off.
STEP4 Press and hold the [MUTE] button on the
STEP4 After you've entered the correct code number other remote until the CLIKR
and the Component has turned Off, press the LED light blinks twice.
[POWER] button to turn the Component back
*Note : The LED will blink 5 times if there was an
On. Now it's time to test the VOLUME and
error in the learning process. In so, repeat
MUTE buttons for the TV (or PLAY and STOP
STEPS 3 and 4. Continue learning other
buttons for VCR and DVD) to make sure they all
buttons by repeating STEPS 3 and 4.
work. If any of the functions do not work as they
should, repeat from STEP 3 using the next 3-digit STEP5 Once you have completed teaching
code number listed for that brand. CLIKR TM -5 all desired commands for that
Component, save the learned commands by
STEP5 Once you have found the correct 3-digit code,
pressing the [COMPONENT] and [ # ]
save it by pressing the same [COMPONENT]
buttons simultaneously until the Component
button one more time. The Component LED
LED blinks 3 times. Now test all the buttons
light will blink twice to confirm that the code
to make sure they learned correctly.
was successfully stored.
D. Erasing a Single Learned Command
Now, program the rest of your Components by
repeating STEPS 1-5
STEP1 Press the [COMPONENT] and [ # ]
*Note : If the Pre-Programmed Method did not
buttons simultaneously for 3 seconds
work, or if the Code Tables do not list your
until the Component LED light turns on.
Component brand, use the Auto-Search
STEP2 Press and hold the button you want to erase
Method as explained in Section B.
for 3 seconds. The Component LED will blink
twice to confirm the erasure.
B. Auto-Search Method
STEP3 To exit, press and hold both the
STEP1 Turn on the Component you want to
[COMPONENT] and [ # ] buttons
program (TV, VCR, DVD or AUX) using your
simultaneously until the Component LED
old remote.
blinks 3 times.
STEP2 Press the [COMPONENT] button (TV, VCR,
E. Erasing All Learned Commands from One Component
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
STEP1 Press the [COMPONENT] and [ # ] buttons
seconds. The Component LED light will turn
simultaneously for 3 seconds until the
on for 30 seconds indicating the unit is ready
Component LED light turns on.
to be programmed.
STEP2 Press and hold both the [COMPONENT]
STEP3 Point the remote toward the Component and
button you want to erase and the [PAUSE]
press the [CH ] or [CH ] button one step
button for 3 seconds. The Component LED
at a time or keep it pressed. The remote will
will blink twice to confirm the erasure.
emit a series of ON/OFF commands.
STEP3 To exit, press and hold both the
Release the [CH ] or [CH ] button as soon
[COMPONENT] and [ # ] buttons
as the Component turns Off.
simultaneously until the Component LED
STEP4 Test functions. (Same as for 3-Digit Code
blinks 3 times.
Programming Method - Section A). If any of
F. Finding a Component Button' s Setup Code Number
the functions do not work as they should,
repeat from STEP 3 using [CH ] or [CH ] If you used either the Auto-Search or Learning
buttons to find the correct code. Methods to program a Component, you may not know
what the correct code number is. Here is a way for
STEP5 Save the code. (Same as for 3-Digit Code
you to identify the code number, so you can record it
Programming Method - Section A).
for future reference.
Now, repeat the Auto-Search Method for those
STEP1 Press the [COMPONENT] button (TV, VCR, DVD
Components you could not program earlier with the
or AUX) you want to verify and the [OK/SEL]
Pre-Programmed Method. If you can't find the right
button simultaneously for 3 seconds. The
code using the Auto-Search Method, try the Learning
Component LED light will turn on for 30 seconds.
Method in Section C.
STEP2 Press the [INFO] button and count the number of
C. The Learning Method
times the Component LED light blinks. This
STEP1 Press the [COMPONENT] button (TV, VCR, number indicates the first digit of the code,
DVD or AUX) to be programmed and the [ # ]
followed by the second and third, each
buttons simultaneously for 3 seconds until
separated by a one second pause when the LED
the Component LED light turns on.
will turn off.
*Note : 10 blinks represents the number zero.
STEP2 Press the [VOL ] button.
Example : One blink, (pause), eight blinks, ( pause) and
STEP3 Press the [TV] button again. The Component
three blinks, indicates code number 183.
TM -5 that you
G. AUX Function: Programming a 5 th Component
To return to original state:
If you wish to restore the CABLE channel control in TV
You can take advantage of the AUX function to program a 5 th
Component such as a second TV, VCR, DVD or Audio Component.
mode, repeat the above steps but press [CBL] in STEP3 .
TM -5 Component STEP1 Turn on the 5 th Component you want to program
J. Programming Volume Control
(TV, VCR, DVD or Audio) using your old remote.
You can program the volume controls (Volume Up,
STEP2 Press the [AUX] button and the [OK/SEL] button
Volume Down and Mute) from one Component to
simultaneously for 3 seconds.The [AUX]
operate in another Component mode. Default volume
Component LED will turn on for 30 seconds.
control settings on the remote control are as follows:
STEP3 Press the [COMPONENT] button you want to
CBL : TV
setup. Point the remote control toward the
DVD : TV
Component and enter the 3-digit code number
assigned to your brand. If you wish to store the CBL volume control in CBL mode,
use the following steps.
*Note : If the 3-digit code number you just entered is the
STEP1 Press the [CBL] button and the [OK/SEL] button
correct number, the Component will turn Off. If it
did not turn Off, continue entering code numbers
listed for that brand until the Component turns Off.
STEP2 Press the [VOL ] button.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any of
STEP3 Press the [CBL] button. The Component LED
the functions do not work as they should, you
need to find a new code.
To return to original state:
STEP5 Once you have found the correct 3-digit code,
If you wish to restore the TV volume control in CBL mode,
save it by pressing the [AUX] button one more
repeat the above steps but press [TV] in STEP3 .
time. The Component LED light will blink twice
to confirm the code was stored. Now when
K. Programming a 'Macro' or Favorite Channel
you press the AUX button, all the buttons will
In CBL mode, the M1, M2 and HELP buttons can be
work with that 5 th Component.
programmed to act as a 'Macro' or Favorite Channel
H. Programming the System On/Off Button
button. This allows you to send up to 10 commands with
one button press.
This allows you to program the System On/Off button so it can
send up to five power On/Off commands with one button press.
STEP1 Press the [CBL] button to select the CBL mode.
STEP1 Press the [CBL] button.
STEP2 Press the [M1,M2 or HELP] button and [OK/SEL]
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.
STEP3 Press up to 10 buttons you wish to store. The
STEP3 Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
then the [POWER] button. Repeat this for other
STEP4 Press the [CH ] button to store the commands
Components until you have stored all the
desired power commands into the [SYSTEM
ON/OFF] button.
STEP4 Press the [CH ] button to save the power L. Low Battery Warning
commands you stored. The [CBL] button will
When the batteries are low and need to be replaced with
blink twice to confirm the commands have
fresh batteries, the Component LED lights will blink 2
been saved.
times in sequence whenever a [POWER] button is
pressed to turn on equipment.
I. Programming Channel Control
You can program the channel controls (Channel Up,
M. Memory Lock System
Channel Down and Last) from one Component to
This remote control is designed to retain programmed
operate in another Component mode. Default channel
memory for 10 years even after batteries are removed
control settings on the remote control are as follows:
from the remote control.
CBL : CBL T V : CBL VCR : CBL
N. Record Your Component Set-up Codes
DVD : DVD AUX : AUX
TV
If you wish to store the TV channel control in TV mode,
use the following steps.
VCR
STEP1 Press the [TV] button and the [OK/SEL] button DVD
simultaneously for 3 seconds. The [TV]
AUX
Component LED will turn on for 30 seconds.
LED will blink twice to confirm the programming.
T V : TV VCR : TV
AUX : AUX
simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
will blink twice to confirm the programming.
button simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
[CBL] Component LED will blink once for each
command entered.
that were selected. The [CBL] Component LED
will blink twice to confirm the storage of
commands.
Set-up Code Number:
Set-up Code Number:
Set-up Code Number:
Set-up Code Number: