Universal Remote Control UR5-8400 Operating Instructions

Operating Instructions 1 Introduction
The remote control is designed to operate
For The UR5-8400
the Scientific Atlanta Explorer 8000, Pioneer
Voyager DVR and the Pace Micro DVR
Cable Remote Control
Series. You can also control the majority of
TV, VCR, DVD and AUDIO equipment on the
market as shown below.
CABLE : Cable Converters TV : Televisions
UR5-8400
VCR : VCRs and TV/VCRs DVD : DVD Players
AUX : Audio Receivers, etc.
Replacing Batteries
2
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown In the
illustration below.
STEP3 Replace the battery compartment cover.
4 Operations
Default State:
Device Default: CABLE
Volume Default: You have the option of controlling
your TV volume and mute through the Cable box,
VCR or DVD. Refer to section G for programming the
volume and mute through your Cable box, VCR or
DVD.
Channel Default: You have the option of controlling
your CABLE channel and number keys through the
TV or VCR. Refer to section F for programming the
channel and number keys through your TV or VCR.
System On/Off button:
Universal Remote Control, Inc. This button is designed to send out power
commands for two, three, four or all five devices with
www.universalremote.com
one button press. Please refer to section E for
OCE-0017D Rev 03 (11/29/05)
details.
3 Button Functions
5 Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit
code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)
STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [SELECT]
button simultaneously for 3 seconds. The device LED will turn on indicating the unit is
ready to be programmed.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED
is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables.
C. To Find the Three Digit Code Number
*Tip : The equipment will turn off when the
That was Stored in the Device.
correct three-digit code number has
been entered. You can verify you have
STEP1 Press the [DEVICE] button (TV, VCR ,
selected the correct code by pressing
DVD or AUX) you wish to verify and
the [POWER] button, the equipment
the [SELECT] button simultaneously
should turn on or turn off.
for 3 seconds. The device LED will
turn on.
*Note : If there is more than one three-digit
number listed for your brand, try one
*Tip : The device LED will turn on for 20
code number at a time until your
seconds. The next step must be
equipment turns off.
entered while the LED is on.
STEP4 Store the three-digit code number
STEP2 Press the [INFO] button.
by pressing the same [DEVICE]
The device LED will blink number of times
button once again. The device LED
indicating the number of each digit of the
will blink twice to confirm that the
code number. Each digit is separated by a 1
code has been stored.
second interval of the LED being turned off.
*Note : Try all the functions on the remote
Example : One blink, three blinks and eight
control. If any of the functions do not
blinks with an interval of 1 second
work as they should, repeat from
of LED being turned off, indicates
Step 2 using the next three-digit code
the code number 138.
number from the same brand list.
Note : Ten blinks is equal to the number 0.
B. Auto Search Method.
D. Programming a second TV to AUX Mode.
If the three-digit code numbers assigned to
STEP1 Press the [AUX] button to be
your brand do not turn off your equipment or
programmed and the [SELECT] button
the code tables do not list your brand, you
simultaneously for 3 seconds.The
can use the Auto Search Method to find the
[AUX] device LED will turn on.
correct three-digit code number for your
equipment by the following steps:
*Tip : The device LED will turn on for 20
seconds. The next step must be
STEP1 Turn on the equipment you wish to
entered while the LED is on.
operate.
STEP2 Press the [TV] device button to pick
STEP2 Press the [DEVICE] button (TV, VCR,
up the TV code table.
DVD or AUX) to be programmed and
STEP3 Point the remote control toward the
the [SELECT] button simultaneously
equipment and enter the three-digit
for 3 seconds. The device LED will
code number assigned to your TV
turn on.
brand from the code tables.
*Tip : The device LED will turn on for 20
STEP4 Store the three-digit code number by
seconds. The next step must be
pressing the [AUX] button once
entered while LED is on.
again. The device LED will blink
twice to confirm that the code has
STEP3 Press the [CH+] or [CH-] button one
been stored.
at a time or keep it pressed. The
remote will emit a series of power
E. Programming the System On/Off Button.
on/off commands. Release the
[CH+] or [CH-] button as soon as the
This is designed to program the System On/Off
equipment turns off.
button so that it can send out up to five power
*Tip : You can verify that you selected the
on/off commands with one button press.
correct code by pressing the [POWER]
STEP1 Press the [CBL] button.
button. The equipment should either
turn on or turn off.
STEP2 Press the [SYSTEM ON/OFF] button
and the [SELECT] button
STEP4 Press the same [DEVICE] button to
simultaneously for 3 seconds. The
store the code. The device LED will
[CBL] button will turn on for 20
blink twice to confirm that the code
seconds.
has been stored.
STEP3 Press the [DEVICE] button and the STEP1 Press the [CBL] button and the
[POWER] button you wish to store in [SELECT] button simultaneously
for 3 seconds.
the [SYSTEM ON/OFF] button and
repeat this until you stored all the The [CBL] device LED will turn on.
power commands into the [SYSTEM
*Tip : The device LED will turn on for 20
ON/OFF] button.
seconds. The next step must be
STEP4 Press the [CH+] button to save the entered while the LED is on.
power commands you stored. The
STEP2 Press the [VOL +] button.
[CBL] button will blink twice to
confirm the saving.
STEP3 Press the [CBL] button.
The device LED will blink twice to
confirm the programming.
F. Programming Channel Control.
To return to original state:
By following the steps below, the user can
If you wish to restore the TV volume
program the channel controls (Channel Up,
Channel Down and Last) from one device to
control in CBL mode, repeat the above
operate in another device mode. The default
steps by pressing [TV] in STEP3 .
channel control settings on the remote
control are as follows:
H. Programming For Advanced Function.
CBL : CBL T V : CBL
In the CBL mode, the BLANK button can be
VCR : CBL DVD : DVD
programmed to act as a macro or favorite
AUX : AUX
channel button. You can send out up to ten
If you wish to store the TV channel control in commands with one button press.
TV mode, use the following steps.
STEP1 Press the [CBL] button to select
the CBL mode.
STEP1 Press the [TV] button and the
STEP2 Press the BLANK button and
[SELECT] button simultaneously for
[SELECT] button simultaneously
3 seconds.
for 3 seconds. The [CBL] device
The [TV] device LED will turn on.
LED will turn on for 20 seconds.
*Tip : The device LED will light on for 20
STEP3 Press up to 10 buttons you wish to
seconds. The next step must be
store. The [CBL] device LED will blink
entered while the LED is on.
once for each command entered.
STEP2 Press the [VOL -] button.
STEP4 Press the [CH+] button to store the
functions that were selected. The
STEP3 Press the [TV] button.
[CBL] device LED will blink twice to
The device LED will blink twice to
confirm the storage of functions.
confirm the programming.
I. Low Battery Warning.
To return to original state:
When the batteries are low and need to be
If you wish to restore the CABLE channel
replaced with fresh batteries, the remote
control in TV mode, repeat the above steps
control LED will blink 2 times in sequence
by pressing [CBL] in STEP3 .
whenever a [POWER] button is pressed to
turn on equipment.
G. Programming Volume Control.
J. Memory Lock System.
By following the steps below, the user can This remote control is designed to retain
program the volume controls (Volume Up, programmed memory for 10 years even
Volume Down and Mute) from one device to after batteries are removed from the
operate in another device mode. The default remote control.
volume control settings on the remote
K.Write your device Set-up codes.
control are as follows:
TV Set-up Code Number:
CBL : TV T V : TV
VCR Set-up Code Number:
VCR : TV DVD : TV
DVD Set-up Code Number:
AUX : AUX
AUX Set-up Code Number:
If you wish to store the CBL volume control in
CBL mode, use the following steps.