Download Print this page

Universal Remote Control AMINO-4 Operating Instructions

4-function remote control

Advertisement

Quick Links

Operating Instructions
1
Introduction
For The AMINO-4
The AMINO-4 remote control is designed to
operate the Amino range of Set-Top Boxes
(STBs) and the majority of TVs, VCRs, DVDs
4-Function Remote Control
and AUDIO components on the market
today, as shown below.
TV
: TVs, Plasma TVs and LCD TVs
VCR : VCRs and DVDs
AUX :Audio Receivers and Amplifiers, etc
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AAA
alkaline batteries.
STEP1 Remove the battery compartment
cover on the back of your remote
control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment
cover.
4
Operations
Device Default: AMINO Set-Top Box.
Volume Default: TV volume and mute through
the TV , with the option of controlling volume and
mute through the STB or AUDIO component.
Refer to section E for programming the volume
and mute through your STB or AUDIO
component.
Channel Default: STB channel and number keys
through the STB, with the option of controlling
Universal Remote Control, Inc.
channel and number keys through the TV or VCR.
Refer to section F for programming the channel
www.universalremote.com
and number keys through your TV or VCR.
OCE-0040A Rev01(10/25/05)
3
Button Functions
Programming the Remote Control
5
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to a particular manufacturer and brand of Audio/Video component.
The three-digit code numbers are listed in the Set-up Code Tables on the backside of this
instruction manual.
STEP1 Turn on the A/V component you wish to program. (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and
the [OK] button simultaneously for 3 seconds. The selected component LED light
will turn on indicating the component is ready to be programmed.
*Tip : If you do not begin entering code numbers within 20 seconds, the component LED
light will turn off and exit set-up mode and you will need to start over.
STEP3 Point the remote control toward the selected component and enter the three-digit
code number assigned to your brand from the code tables.
*Tip : The component will turn off when the
STEP4 Press the same [COMPONENT]
button to store the code. The
correct three-digit code number has been
component LED light will blink twice
entered. You can verify you have selected the
to confirm that the code has been
correct code by pressing the [POWER]
stored.
button. The component should turn on or off.
*Note : 2 colons If there is more than one
C. To Find the Three-Digit Code Number
three-digit number listed for your
That was Stored in the component.
brand, try one code number at a time
until your component turns off.
STEP1 Press the [COMPONENT] button
(TV, VCR, DVD or AUX) you wish to
STEP4 Store the three-digit code number
verify and the [OK] button
by pressing the same [COMPONENT]
simultaneously for 3 seconds.
button once again. The component
*Tip : If you do not press the [INFO] button
LED will blink twice to confirm that the
within 20 seconds, the component LED
code has been stored.
light will turn off and exit set-up mode
*Note : Try all the functions on the remote
and you will need to start over.
control. If any of the functions do
STEP2 Press the [INFO] button. The
not work as they should, repeat from
component LED light will indicate the
Step 2 using the next three-digit code
three digits that comprise the code
number from the same brand list.
number by blinking the corresponding
number of times for each digit,
B. Auto Search Method.
separated by a one second interval,
If the three-digit code numbers assigned to
during which time the component LED
your brand do not turn off your component or
light will turn off.
the code tables do not list your brand, you
Example : One blink, three blinks and eight
can use the Auto Search Method to find the
blinks, separated by a one second
correct three-digit code number for your
interval during which time the
component by performing the following
component LED light turns off,
steps:
indicates a code number of 138.
STEP1 Turn on the component you wish to
*Note : Ten blinks is equal to the number 0.
operate.
D. Programming AUX to operate a
STEP2 Press the [COMPONENT] button (TV,
fourth component (i.e., a second
VCR, DVD or AUX) to be programmed
TV, VCR, or DVD or AUDIO)
and the [OK] button simultaneously
for 3 seconds. The component LED
STEP1 Turn on the component you wish to
will turn on.
operate.
*Tip : If you do not press either the CH+ or
STEP2 Press the [AUX] button and the [OK]
CH- button within 20 seconds, the
button simultaneously for 3 seconds.
component button LED light will turn off
The [AUX] LED light will turn on.
and exit set-up mode and you will need
*Tip : If you do not press the desired
to start over.
component button within 20 seconds,
the [AUX] LED light will turn off and exit
STEP3 Press the [CH+] or [CH-] button one
set-up mode and you will need to start
step at a time or keep it pressed. The
over.
remote will emit a series of Power
ON/OFF commands. Release the
STEP3 Press the [COMPONENT] button you
[CH+] or [CH-] button as soon as the
wish to operate.
component turns off.
STEP4 Point the remote control toward the
*Tip : You can verify that you selected the
component you want to program
correct code by pressing the [POWER]
and enter the three-digit code
button again. The component should
number assigned to your TV brand
either turn on or off.
from the code tables.
*
Note : The [AUX] LED light will blink once
F. Programming Channel Control.
for each button pressed. Once you
By following the steps below, the user can
enter the correct code number, the
program the channel controls (Channel Up,
component will turn off. If the
Channel Down and Last) from one
component does not turn off, press
component to operate in another component
the next code numbers listed for your
mode. The default channel control settings
brand until the component turns off.
on the remote control is as follows:
STEP5 Store the three-digit code number
STB : STB
TV : STB
by pressing the [AUX] button once
VCR : VCR
AUX : AUX
again. The component LED light will
If you wish to store the TV channel control
blink twice to confirm that the code
in TV mode, use the following steps.
has been stored.
STEP1 Press the [TV] button and the [OK]
*Note : Now turn on the component and test
button simultaneously for
the component functions on the
3 seconds until the TV LED light
remote control. If any function does
turns on.
not work properly, repeat from STEP
2 using the next code number listed
*Tip : If you do not press the [VOL-] button
for your component brand until you
within 20 seconds, the TV LED light
find a perfect match.
will tiurn off and exit set-up mode
and you will need to start over.
E. Programming Volume Control .
STEP2 Press the [VOL -] button.
By following the steps below, the user can
STEP3 Press the [TV] button.
program the volume controls (Volume Up,
The TV LED light will blink twice to confirm
Volume Down and Mute) from one device
the programming.
to operate in another device mode. The
To return to the original default state:
default volume control settings on the remote
control is as follows :
If you wish to restore the STB channel
STB : TV
TV : TV
control in TV mode, repeat the above steps
by pressing [STB] in STEP3 .
VCR : TV
AUX : AUX
lf you wish to store the STB volume control
G. Low Battery Warning.
in STB mode, use the following steps.
When the battery is low and needs to be
STEP1 Press the [STB] button and the
replaced with fresh batteries, the remote
[OK] button simultaneously for 3
control component LED lights will blink 2
seconds until the component LED
times in sequence whenever a [POWER]
light turns on.
button is pressed to turn on components
*Tip : If you do not press the [VOL+] button
H. Memory Lock System.
within 20 seconds, the component LED
light will turn off and exit set-up mode
This remote control is designed to retain
and you will need to start over.
programmed memory for 10 years even
STEP2 Press the [VOL +] button.
after batteries are removed from the
remote control.
STEP3 Press the [STB] button.
The STB LED light LED will blink twice to
I. Write your component Set-
confirm the programming.
up codes.
To return to the original default state:
TV Set-up Code Number :
If you wish to restore the TV volume
VCR Set-up Code Number :
control in STB mode, repeat the above steps
AUX Set-up Code Number :
by pressing [TV] in STEP3 .

Advertisement

loading

Summary of Contents for Universal Remote Control AMINO-4

  • Page 1 Operating Instructions Introduction For The AMINO-4 The AMINO-4 remote control is designed to operate the Amino range of Set-Top Boxes (STBs) and the majority of TVs, VCRs, DVDs 4-Function Remote Control and AUDIO components on the market today, as shown below.
  • Page 2 Set-up Code Tables MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST MAKER(BRAND) NAME REALISTIC GIBRALTER 004 073 GOLDSTAR 004 106 119 110 112 113 127 143 RUNCO MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST GRUNPY 028 043 SAMPO ADMIRAL 072 081 160 161 096 HALL MARK SAMSUNG ADVENT...