Operating The Tiller; Stopping The Engine And Tiller - Troy-Bilt Super Bronco Operator's Manual

Stopping the Engine and Tiller

1. To stop the wheels and tines, release the
Forward Clutch Bail (all models) or the Re-
verse Clutch Control (Super Bronco & Pro-
Line) — whichever control is in use.
2. To stop the engine, put the ignition
switch and/or the throttle control lever in
the "OFF" or "STOP" position.

OPERATING THE TILLER

The following operating instructions pro-
vide guidelines to using your tiller effec-
tively and safely. Be sure to read Tilling
Tips & Techniques in this Section before
actually putting the tines into the soil.
This is a "Counter-Rotating-Tine" (CRT)
tiller. It operates differently from "Stan-
dard-Rotating-Tine" (SRT) tillers. As the
wheels pull forward, the tines rotate back-
ward, creating an "uppercut" action which
digs deeply, uprooting soil and weeds.
1. Follow the Pre-Start Checklist at the be-
ginning of this Section. Be sure that the
wheels are in the WHEEL DRIVE position.
2. Move the Depth Regulator Lever all the
way down, so that the tines clear the
ground. Use this position when practicing
with the tiller and when traveling between
tilling sites. Before actually tilling, move
the lever to the desired depth setting (see
Tilling Tips & Techniques).
Fig. 4-2: Use one hand to guide tiller when
moving forward.
3. Start engine and allow it to warm up.
Then put throttle in "FAST" setting.
4. For forward motion of the wheels and
power to the tines:
(a) Pull Forward Clutch Bail (Fig. 4-1) up
against handlebar. Release bail to stop for-
ward motion of wheels and tines.
(b) When tilling, relax and let the wheels
pull the unit while the tines dig. Walk be-
hind and a little to one side of the unit. Use
one hand, yet keep a light—but secure—
grip on the handlebar (while keeping your
arm loose). See Fig. 4-2. Let the unit move
at its own pace and do not push down on
the handlebars to try and force the tines to
dig deeper — this takes weight off the
wheels and reduces traction.
WARNING:
down on the handlebars to try
to make the tiller till more
deeply. This prevents the
wheels from holding the tiller
back and can allow the tines to
rapidly propel the tiller forward,
which could result in loss of
control, property damage, or
personal injury.
5. For reverse motion of the wheels and
tines (Super Bronco & Pro-Line):
(a) Look behind and exercise caution when
operating in reverse. Do not till while in
reverse.
(b) Stop all forward motion. Lift handlebar
with one hand until tines are off the ground
and then pull Reverse Clutch Control knob
out (see Fig. 4-3). To stop reversing, let go
of Reverse Clutch Control knob.
Fig. 4-3: Raise tines off ground and look
behind when moving in reverse.
6. To move the Bronco in reverse for short
distances:
(a) Release forward Clutch Bail. Then lift
handlebar until tines are off the ground.
13
(b) Swing the handlebar to the left so the
right wheel takes a "step" backward. Next
swing the handlebar to the right so the left
wheel "steps" backward. Repeat as needed.
(c) If longer distances need to be covered
in reverse, shut off the engine, then place
the two wheels in FREEWHEEL.
7. To Turn the Tiller Around:
(a) Practice turning the tiller in a level,
open area. Be very careful to keep your feet
and legs away from the tines.
(b) To begin a turn, lift the handlebars until
the tines are out of the ground and the engine
and tines are balanced over the wheels (Fig.
4-4).
(c) With tiller balanced, push sideways on
handlebar to steer in direction of turn (Fig.
4-5). After turning, slowly lower tines into
Do not push
soil to resume tilling.
Fig. 4-4: To begin turn, lift handlebars until
tines are out of ground and unit is balanced.
Fig. 4-5: With tines out of ground, push han-
dlebars sideways to turn tiller.
Stopping the Tiller and Engine
1. To stop the wheels and tines, release the
Forward Clutch Bail (all models) or the Re-
verse Clutch Control (Super Bronco * Pro-
Line) — whichever control is in use.
2. To stop the engine, put the ignition
switch and⁄or the throttle control lever in
the "OFF" or "STOP" position.