Trane IntelliPak SCWG 020, SCWG 025, SCWG 030, SCWG 035, SWG 020, SWG 025, SWG 030, SWG 035, SCRG 020, SCRG 025, SCRG 032, SRG 020, SC Installation Manual page 81

• VO relay – energized
• Exhaust fan (field-installed) - on
• Exhaust damper (field-installed) - open
PURGE sequence "D"
This sequence could be used for purging
the air out of a building before coming out
of unoccupied mode of operation on VAV
units. Also, it can be used to purge smoke
or stale air.
• Supply fan – on
• Supply fan VFD – on (60 Hz)
(if equipped)
• Inlet guide vanes/VAV boxes – Open
(if equipped)
• Outside air damper – Open
• Heat – all stages – Off, Modulating heat
output at 0 vdc
• Occupied/unoccupied output – Energized
• VO relay – Energized
• Exhaust fan (field-installed) - On
• Exhaust damper (field-installed) - Open
PURGE with duct pressure control "E"
This sequence can be used when supply
air control is required for smoke control.
• Supply fan – on
• Supply fan VFD – on (if equipped)
• Inlet guide vanes – controlled by supply
air pressure control function with
supply air pressure high limit disabled
• Outside air dampers – open
• Heat – all stages – off, hydronic heat
output at 0 vdc
• Occupied/unoccupied output – energized
• VO relay – energized
• Exhaust fan (field-installed) - on
• Exhaust damper (field-installed) - open
Note: Each system (cooling, exhaust,
supply air, etc.) within the unit can be
redefined in the field for each of the five
sequences, if required. Also the definitions
of any or all of the five sequences may be
locked into the software by simple key
strokes at the human interface panel. Once
locked into the software, the sequences
cannot be changed.
T rane Communications
Interface Module (TCI) - Option
TM
used with T rane ICS
The Trane communication interface
module allows external setpoints for
most of the unit functions to be
communicated to the unit's UCM network
TM
via a Trane ICS systems. DIP switch
settings on the TCI module for this
SCXG-SVX01B-EN
Owner
application are; switch 1 "off, " 2 "on, " and
3 "off. "
Exhaust/Comparative
Enthalpy Module (ECEM) - On
Units with Comparative
Enthalpy Option
The exhaust/comparative enthalpy
module receives information from the
return air humidity sensor, and the RTM
outside air temperature sensor and
outside air humidity sensor, the outside
air humidity sensor and temperature
sensor to utilize the lowest possible
enthalpy level when considering
economizer operation. In addition, it
receives space pressure information to
maintain the space pressure within the
setpoint control band. Refer to the Figure
O-GI-1 for humidity vs. voltage values.
Figure O-GI-1. ECEM Relative Humidity vs.
Voltage.
Figure O-GI-2. Velocity Pressure Trans-
ducer/Solenoid Assembly.
General
Information
Ventilation Control Module
(VCM) - Available only with
T raq™ Damper Option
The ventilation control module (VCM) is
located in the airside economizer section
of the unit and linked to the unit's UCM
network. Using a velocity pressure
transducer/solenoid (pressure sensing
ring) in the fresh air section allows the
VCM to monitor and control fresh air
entering the unit to a minimum airflow
setpoint. See Figure O-GI-2 for a detail
view of the velocity pressure transducer/
solenoid assembly.
An optional temperature sensor can be
connected to the VCM to enable control
of a field installed fresh air preheater.
Also, a field-provided CO sensor can be
2
connected to the VCM to control CO
reset. The reset function adjusts the
minimum cfm upward as the CO
concentrations increase. The maximum
effective (reset) setpoint value for fresh
air entering the unit is limited to the
system's operating cfm. Table O-GI-5 lists
the minimum outside air cfm vs. input
voltage.
Table O-GI-5. Minimum Outside Air
Setpoint w/VCM Module and Traq™
Sensing.
Unit Input Volts
SXWG 20 0.5 - 4.5 vdc
SXWG 25 0.5 - 4.5 vdc
SXWG 30 0.5 - 4.5 vdc
SXWG 35 0.5 - 4.5 vdc
SXRG 20 0.5 - 4.5 vdc
SXRG 25 0.5 - 4.5 vdc
SXRG 32 0.5 - 4.5 vdc
2
2
CFM
6,350-8,500
7,250-10,625
7,250-12,750
7,250-14,875
7,250-8,500
7,250-10,625
7,250-13,600
81