Sign in today to find solutions:

Don't have an account? Sign up

 
TD-8817
ADSL2/2+ Ethernet/USB Router
Rev: 1.0.2
1910010018

Summary of Contents

  • Page 1

    TD-8817 ADSL2/2+ Ethernet/USB Router Rev: 1.0.2 1910010018...

  • Page 2

    Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4

    Package Contents The following contents should be found in your package: One TD-8817 ADSL2/2+ Ethernet/USB Router One AC power Adapter for TD-8817 ADSL2/2+ Ethernet/USB Router Quick Installation Guide One RJ45 cable One USB cable Two RJ11 cables One ADSL splitter...

  • Page 5: Table Of Contents

    Chapter 1. Introduction ... 1 Product Overview ... 1 Main Features ... 1 Conventions ... 2 Chapter 2. Hardware Installation ... 3 The Front Panel ... 3 The Back Panel... 3 Installation Environment ... 4 Hardware installation procedures... 4 Chapter 3. Quick Installation Guide ...

  • Page 6

    4.6.3 Firmware...45 4.6.4 System Restart...47 4.6.5 Diagnostic...48 Help... 48 Appendix A: Specification... 50...

  • Page 7: Chapter 1. Introduction, Product Overview, Main Features

    Chapter 1. Introduction 1.1 Product Overview Thank you for choosing the TD-8817 ADSL2/2+ Ethernet/USB Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. TD-8817 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors.

  • Page 8: Conventions

    Supports firmware upgrade and Web management. 1.3 Conventions The Router or device mentioned in this User guide stands for TD-8817 without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.

  • Page 9: Chapter 2. Hardware Installation, The Front Panel, The Back Panel

    Method one: When the device is working, please press the reset button of the Router, keep the reset button pressed down for more than five seconds. Method two:Restore the default setting from “Maintenance-SysRestart” of the Router's TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 2-1...

  • Page 10: Installation Environment, Hardware Installation Procedures

    Third Step: Plug one end of the provided AC Power Adapter( 9V/ 0.8A ) into the Power jack on the Router and the other end to a standard electrical outlet( 220V~50/ 60HZ ). Last Step: Check the line connection to see if everything is ready. Power up finally. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 2-3...

  • Page 11: Chapter 3. Quick Installation Guide, Configure Pc

    Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8817 or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it.

  • Page 12

    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3...

  • Page 13

    Enter. To continue, please type ping 192.168.1.1 on the following appeared command prompt screen and then press Enter. If the result displayed is similar to the screen below, the connection between your PC and the Router has been established. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-4 Figure 3-5...

  • Page 14: Usb Configuration

    3.2 USB Configuration If you use the USB interface, First, you must install the USB’s driver to the computer. You can obtain the drivers from the provided CD, or download from our website. (http://www.tp-link.com) USB Drive installation procedures Step 1: Please connect your PC to the Router through the USB port at first, then open the relative operating system folder in the CD, and double click Setup.exe to install the USB...

  • Page 15

    Step 3: You will see Figure 3-8 as follow, please wait a moment. Step 4: After that, you will see Figure 3-9. Click Finish to complete the installation. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-7 Figure 3-8...

  • Page 16: Login

    After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Setup screen. You can follow the steps below to complete the Quick Setup. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-9...

  • Page 17

    Step 2: Configure the time for the Router, and then click the NEXT button. Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-10...

  • Page 18

    Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click Next. Step 5: Click NEXT to finish the Quick Start. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 3-13 Figure 3-14 Figure 3-15...

  • Page 19: Chapter 4. Software Configuration, Status

    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility.

  • Page 20: Quick Start, Interface Setup

    Login". 4.3 Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN. Click any of them, and you will be able to configure the corresponding function. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-2 Figure 4-3...

  • Page 21: Internet

    VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority. • Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-4...

  • Page 22

    TCP MTU Option: Enter the TCP MTU as your desire. Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-5...

  • Page 23

    DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-6...

  • Page 24

    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-7 Username: Enter your username for your PPPoE/PPPoA connection. Password: Enter your password for your PPPoE/PPPoA connection. Encapsulation: For both PPPoE/PPPoA connection, you need to specify the type of Multiplexing, either LLC or VC Mux.

  • Page 25

    Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-8...

  • Page 26

    Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254. • IP Pool Count: The max user pool size. • Lease Time: The length of time for the IP lease. After the dynamic IP address has TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-10...

  • Page 27

    LAN port, and make sure the routing table has the correct routing entry. • DHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN side. Note: If you select Disabled, the DHCP function will not take effect. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-11...

  • Page 28: Advanced Setup, Firewall, Routing

    SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. 4.4.2 Routing Choose “Advanced Setup→Routing” menu, and you will see the routing information in the next screen (shown in Figure 4-14). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-12 Figure 4-13...

  • Page 29

    RIP broadcasts. If No, this route is kept private and is not included in RIP broadcasts. 4.4.3 NAT Choose “Advanced Setup→NAT” menu, you can setup the NAT (Network Address Translation) function for the Router (shown in Figure 4-16). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-14 Figure 4-15...

  • Page 30

    DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. 4.4.3.2. Virtual Server Choose “Advanced Setup→NAT→Virtual Server” in Figure 4-16, you can configure the Virtual Server in the next screen. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-16 Figure 4-17...

  • Page 31

    Enter the index of assigned entry, click the DELETE button to delete the entry. Click the Back button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-18...

  • Page 32

    IP address and Public End IP is the ending public IP address. If you have a dynamic IP, enter 0.0.0.0 as the Public Start IP. Address Mapping List: This displays the information about the Mapping addresses. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-19...

  • Page 33

    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide To add a mapping rule: Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs”. Then select the tab IP Address Mapping (shown in Figure 4-19). Note: IP Address Mapping is only available for VCs with Multiple IPs.

  • Page 34

    Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule. • Source MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-21...

  • Page 35: Vlan

    VLANs. ATM VLAN: Using LAN Emulation (LANE) protocol to map Ethernet packets into ATM cells and deliver them to their destination by converting an Ethernet MAC address into an ATM address. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide...

  • Page 36

    (frames with null (0) VID) received on this port. Define VLAN Group Click Define VLAN Group in Figure 4-22, you can define VLAN groups in the next screen (shown in Figure 4-24). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-22 Figure 4-23...

  • Page 37: Adsl

    Choose “Advanced Setup→ADSL”, you can select the ADSL Type and ADSL Mode in the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service provider. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-24...

  • Page 38: Access Management

    Choose “Access Management→ACL”, you can see the next screen (shown in Figure 4-27). You can specify the client to access the ADSL Router once setting his IP as a Secure IP Address through selected applications. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-25...

  • Page 39: Filter

    Select IP/Mac Filter as the Filter type, and select IP as the Rule type (shown in Figure 4-28), then you can configure the filter rules based on IP address. The filtering includes Outgoing and Incoming, the detailed descriptions are provided below. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-27...

  • Page 40

    IPs (Source IP Address and Destination IP Address), If select LAN as a interface, the filter will match the IP traffic of LAN port with specified IPs. Direction: Select the direction for this IP Filter rule. There are three filtering directions: Both, Incoming, Outgoing. Note: TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-28...

  • Page 41

    Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Both” for the first rule. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide...

  • Page 42

    Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide...

  • Page 43

    00-0A-EB-00-07-5F to access the Internet, you can configure as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2). Step 1: Select the “IP/MAC Filter” as the Filer Type Selection: TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-29...

  • Page 44

    DELETE button to delete the entry. 4.5.2.3. Application Filter Select Application Filter as the Filter type (shown in Figure 4-30), then you can configure the filter rules based on application. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide...

  • Page 45

    Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.4. URL Select URL as the Filter type (shown in Figure 4-31), then you can configure the filter rules based on URL. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-30...

  • Page 46

    Other operation for the entries as shown in Figure 4-28: Select the URL Index to view or modify the entry. Select the URL Index to locate the specific rule, and then click the DELETE button to delete the entry. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-31...

  • Page 47: Snmp, Upnp

    Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-32...

  • Page 48: Ddns, Cwmp

    Choose “Access Management→CWMP”, you can configure the CWMP function in the screen (shown in Figure 4-35). The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-34...

  • Page 49: Maintenance, Administration

    Click any of them, and you will be able to configure the corresponding function. 4.6.1 Administration Choose “Maintenance→Administration”, you can set new password for admin in the screen (shown in Figure 4-37). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-35 Figure 4-36...

  • Page 50: Time Zone

    Daylight Saving dates and the system time will automatically adjust on those dates. NTP Server automatically Select NTP Server automatically as the Synchronize time, you only need to set the time zone. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-37 Figure 4-38...

  • Page 51: Firmware

    (shown in Figure 4-41). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile TD-8817 ADSL2/2+ Ethernet/USB Router User Guide...

  • Page 52

    To upgrade the router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (www.tp-link.com). Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse button to locate the update file.

  • Page 53: System Restart

    Step 2: Click the UPGRADE button to complete. 4.6.4 System Restart Choose “Maintenance→System Restart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-44). TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-42 TD-8817...

  • Page 54: Diagnostic, Help

    LAN and WAN sides in the screen (shown in Figure 4-45). 4.7 Help Choose “Help”, you can view the help information for configuration of any function. TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-44...

  • Page 55

    TD-8817 ADSL2/2+ Ethernet/USB Router User Guide Figure 4-46 Note: Click the tab, and you will be able to get the corresponding information.

  • Page 56: Appendix A: Specification

    Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later System Requirement Windows 9x/ME/2000/XP/Vista Working Temperature 0℃ ~ 40℃ Working Humidity 10% ~ 90% RH (non-condensing) Storage Temperature -40℃ ~ 70℃ Storage Humidity 5% ~ 90% RH (non-condensing) TD-8817 ADSL2/2+ Ethernet/USB Router User Guide General Physical and Environment...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: