List Of Supported Signals (Rgb Signals); List Of Supported Signals (Y/P B /P R Signals); List Of Supported Signals (Video, S-Video Signals); Pin Assignment Of Computer-1/2 & Monitor Terminals - Toshiba TDP-T30 Owner's Manual

Specifications (Continued)
List of supported signals (Y/P
Signal format fh(kHz)
480i(525i)@60Hz 15.73
480p(525p)@60Hz 31.47
576i(625i)@50Hz 15.63
576p(625p)@50Hz 31.25
720p(750p)@60Hz 45.00
720p(750p)@50Hz 37.50
1080i(1125i)@60Hz 33.75
1080i(1125i)@50Hz 28.13
1035i(1125i)@60Hz 33.75
1152i(1250i)@50Hz 31.25

List of supported signals (Video, S-Video signals)

Video mode fh(kHz)
NTSC 15.73
PAL 15.63
SECAM 15.63
PAL-M 15.73
PAL-N 15.63
PAL-60 15.73
NTSC4.43 15.73
Pin assignment of COMPUTER-1/2 & MONITOR terminals
5 1
10 6
15 11
Mini D sub 15 Pin connector
Input Signal
• RGB input
RGB signals: 0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
• Y/P /P input
B R
Y signal: 1.0V (p-p) 75 Ω
P /P signals: 0.7V (p-p) 75 Ω
B R
/P signals)
B R
fv(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60.00
50.00
fv(Hz) fsc(MHz)
60 3.58
50 4.43
50 4.25 or 4.41
60 3.58
50 3.58
60 4.43
60 4.43
Pin Pin description
No. During RGB input During Y/PB/PR input
1 Video signal (R) Color difference signal (PR)
2 Video signal (G) Luminance signal (Y)
3 Video signal (B) Color difference signal (PB)
4 GND ∗
5 GND
∗
6 GND (R) GND (P )
R
7 GND (G) GND (Y)
8 GND (B) GND (P )
B
9 N.C ∗
10 GND
∗
11 GND ∗
12 N.C ∗
13 Horizontal sync signal ∗
14 Vertical sync signal ∗
15 N.C
∗
∗ Do not connect anything.
42

CONTROL terminal

Pin assignment
Pin No.
7 1
8 6 2
3
4
5 3
5
4 6
7
2 1
8
Mini DIN 8 pin connector
Interface format
1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:
2 Communication format STX (02h) Command (3Byte) ETX (03h)
Only 1 command valid per communication.
3 Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4 Replies Acknowledge
No acknowledge
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
Main Commands
Item Command
Power on PON
Power off POF
Icon display on MO0
Icon display off MO1
Auto setting (RGB input) PAT
Status display on DON
Status display off DOF
Note
• Contact your dealer for control cable and other commands.

Separately Sold Product

Replacement Lamp Model TLPLV5
Signal Name Description
RXD
Receiving data
CTS Consent to send
DSR Data set ready
GND Signal ground
RTS Request to send
N.C No connection
TXD Sending data
GND Signal ground
1 bit
ACK (06h) CR (0Dh) Data ... Normally ended
ACK (06h) ESC (1Bh) ... Aborted
NAK (15h)
Item Command
Computer (1) input select
Computer (2) input select
Video input select
S-video input select
43
IN1
IN2
IN3
IN4