Advertisement
Quick Links
EN
Installation and User Manual for Vice
HV 519 , 519S, 581
Clamping system HV 519, 519S, 581 (
1. Line cassette
2. Face
3. Spindle
4. Nut
CW
CCW
6
2
1. Foreword:
Read carefully all instructions of this User Manual, especially sections concerning work safety.
These sections are marked by a warning triangle.
2. Important notice ! !
- the head (6) has an opening for the hadle ∅28-25mm [1,102"- 0,984"]
- to ensure safe fixing of the vice, the minimum workbench or collar workbench thickness is
100mm [3,937"]
- after unpacking, the vice must be cleaned of all preservative grease
- prior to installation, the HV vice must be dismantled into two parts turning the spindle clockwise
(CW) until the entire cover (8) slides off the conduit cassette (1)
- assembly is done by reverse procedure and turning the spindle counter clockwise (CCW)
- vice installation is easier when the workbench is turned upside down
- to ensure correct vice operation it is recommended to lubricate the spindle (3) and guiding
grooves of the conduit cassette (1) with oil once a week
see Fig. 1
5. Front board
6. Head with hole for handle 28-25mm [1,102"- 0,984"]
7. Securing pin
8. Cover vice
5
3
Page 1 (of 7)
) :
Fig. 1
1
4
8
7
Advertisement
Summary of Contents for York HV 519S
- Page 1 Installation and User Manual for Vice HV 519 , 519S, 581 Clamping system HV 519, 519S, 581 ( see Fig. 1 1. Line cassette 5. Front board 6. Head with hole for handle 28-25mm [1,102“- 0,984“] 2. Face 3. Spindle 7.
-
Page 2: General Instructions
3. Standard Clamping by Turning the Spindle By turning the spindle (3) clockwise (CW) the vice clamp. By turning the spindle (3) counter clockwise (CCW) the vice disengage. 4. General Instructions The wood vice is mounted to the lateral face of a workbench flush with the outside edge. The exact position is selected depending on the design of the workbench and HV vice size. - Page 3 Installation jaw with of the line cassette Jaw with of the line Workbench board cassette thickness corresponding jaw thickness Depth of mortising on front board (5) min. 9 [0,354“] - gross up of size bolthead Line cassette Spacer underneath Cover vice Fig.
- Page 4 5. Dimensions and drilling of cover vice The vice jaw and spacer should be made of fine-grained hard wood eventually plywood. Fix the cover vice with spacer so that the top edge jaw is flush with the top of the workbench board.
- Page 5 6. Making clamping jaw with of the line cassette Dimensions minimum and optimum clamping jaw see page No.3, Fig.2b. Making clamping jaw with of the line cassette is recommended made with finish allowance. First is make mortising on front board into clamping jaw, follow drilling hole for spindle (∅30 for HV 519(S) and HV 581).
- Page 6 7. Vice installation on a workbench Required tools: - handheld drill / bench top upright drill - wood drill bit ∅ : 3, 4, 5, 6, 14, 30, 40 mm [0,12", 0,16", 0,2", 0,24", 0,55", 1,18", 1,58"] - manual / electrical screwdriver – depending on type and size of used screws - wood saw - screw vice - hammer / mallet...
- Page 7 After tighten vice first is must to seat all edges of clamping jaw with the workbench board. See Fig.7. Fig.7 Finally, check the operation of the vice’s system. By turning the spindle (3) clockwise (CW) the vice clamp. By turning the spindle (3) counter clockwise (CCW) the vice disengage. Vice disassembly is done by reversing the steps described in this User Manual.