Introduction Safety Information/Useful Tips ... 3 Before Calling Service ... 4 Basic Installation/Functions Hooking Up Your TV (Basic Connection)... 5 Use/Care of Remote Control ... 5 Back Connectors ... 6 Remote Controls ... 7 TV Installation Activating TV Setup Menu ... 8 TV Setup Main Menu ...
AFETY AFETY NFORMATION • Disconnect mains plug when : – the red light below the TV screen is flashing continuously. – a bright white line is displayed across the screen. – cleaning the TV screen. Never use abrasive cleaning agents. Use a slightly damp chamois leather or soft cloth.
EFORE Below is a list of frequently occurred symptoms. Before you call for service, make these simple checks. Some of these symptoms can easily be rectified if you know what to do. Symptom Colour patch • (uneveness) • No power •...
OOKING UP YOUR Note Always remove the batteries from the remote control handset if handset is not used for a long period. This can help prevent damage to handset from possible battery leakage. p1-7 TV (B ASIC ONNECTION NTENNA ONNECTION •...
ARNING ISK OF ELECTRIC SHOCK O NOT CONNECT TELEPHONE CABLE TO Monitor Component Video Input Ext Spk RJ 12 For “Y” models Monitor Component Video Input Ext Spk RJ 12 For “R” models p1-7 ONNECTORS DO NOT REMOVE THIS COVER MART Smart Card slot Note:...
Three types of remote controls could be used for setup purpose: RC2886 (RC19335018/01) For the purpose of explanation, RC2886/RC2887 is used. Remote control RC2573GR is optional and can be purchased separately. Refer to its accompanying guide “RC2573GR Remote Control Instructions” for details of its operation. p1-7 EMOTE ONTROLS...
CTIVATING RC2886/RC2887 ITH REMOTE CONTROL (only when SECURITY in the TV SETUP menu is set to LOW). To activate TV Setup menu. Select a channel number. Key in 3 1 9 7 5 3. Press H . The above sequence should be done within 20 seconds and TV SETUP menu will appear. RC2573GR ITH REMOTE CONTROL (only in TV Commercial mode)
TV S ANGUAGE When you first enter the TV SETUP menu, LANGUAGE is highlighted. You may select other languages available with the OF CHANNELS Show the number of channels under each category type. Enter the TV SETUP menu and highlight NO.OF CHANNELS. LANGUAGE NO.
NPUT This menu item selects the input source to be assigned per channel. The selectable sources are FRONT END, AV1, AV2, AV3, CVI, AV2YC or AV3YC (dependent on model). To select press the ) or ˝ OLOUR TANDARD Selects the colour and sound system of transmission. TORE When this is activated, the TV will start at the lowest valid frequency to search for a signal.
ELETEXT ANGUAGE This option allows toggling between different Teletext languages. W for Western English or A for Arabic. The default selection is W. For models without Teletext feature, selection of W or A has no effect. IDEO LANK To blank out picture of the channel, select YES. UDIO To switch off the sound of the channel, select YES.
Page 13
TV S RIGHTNESS OLOUR Enter the TV SETUP menu and highlight accordingly. Preset the TV by adjusting the brightness, colour, contrast, sharpness or tint (applicable for NTSC signal only) of the picture. All these 5 items are also accessible to users via the (only for 29HT model) OTATION Adjust the tilt effect of the picture on screen.
Page 14
I/II UDIO This menu item is to enable the switching from Stereo or Nicam Stereo to Mono, or to choose between Dual I or Dual II in case of bilingual transmission. When the sound mode is switched to Mono, the indication is displayed in red. Press the the required audio mode.
Page 15
OWER Select STANDARD, STANDBY or FORCED mode. The different modes are as explained below: STANDARD: TV will be automatically switched to the last status (STANBY or ON) whenever the mains power is turned ON or resumed after a power interruption. STANDBY: TV will be automatically switched to STANBY(even if the last status was ON) whenever the mains power is turned ON or resumed after a power interruption.
Page 16
NTERFACE Enables the communication of the TV with the DCM when YES is selected. This is specifically applicable to the Interactive System TV, providing the interactivity feature between a DCM card of the Service Provider and the dedicated System TV. UDIO IDEO To blank the screen when no signal is received.
Page 17
O CREATE MESSAGE WITH Highlight LINE 2 with the will appear in the first character position. To input characters, press the ) key to select from the list:- A to Z, 0 to 9, ¸ ) key to go to the next character position or the ˙...
ELETEXT CCESS Select YES to enable the Teletext feature or NO to disable the Teletext feature. For models without Teletext feature, selection of YES or NO has no effect. ECURITY Select HIGH and only remote control RC2573GR can be used to enter TV Setup menu. LARM The Alarm feature will require the time to be set correctly according to the CLOCK SETUP procedure in page 12.
Page 19
This page is intentionally left blank p13-20 2/4/05, 3:21 PM...