Secura Key ET-SR-X-K Installation Instructions

ET-SR-X-K / ET-SR-R-S / ET-SR-R-K Installation Instructions RKDT-SR-M / RKDT-SR-S Installation Instructions
Use supplied
screw
SWITCHPLATE INSTALLATION DIAGRAM
Use appropriate
Fastener
MULLION INSTALLATION DIAGRAM
Reader
Housing
INSTALLATION STEPS FOR RKDT-SR-S:
1. If mounting the unit outdoors, especially on a
rough surface like masonry, we recommend
3/4" Diameter hole in
that you seal the reader with silicone caulking.
mounting surface for
2. Drill holes as needed per installation
Use supplied
wiring
diagram shown to the left or install a single
screw
gang j-box.
3. Run field wiring to reader location and feed
into j-box or through cable hole.
4. Attach the mounting plate to the mounting
surface or j-box with the appropriate
Mounting
fasteners.
Surface
ET-SR-X-K
5. Splice the connector pigtail to field wiring.
MULLION INSTALLATION DIAGRAM
Insert the connector into the back of the reader.
6. Attach the housing to the mounting plate by inserting the two tabs
TYPICAL INSTALLATION
inside the top of the housing into the two slots at the top of the
mounting plate.
+
RED
7. Secure by installing supplied screw into the hole at the bottom of
the reader.
BLACK
OUTPUT RELAY
3/4" Diameter hole in
INSTALLATION STEPS FOR RKDT-SR-M
WHITE/BLACK
mounting surface for
wiring
1. If mounting the unit outdoors, especially
READER
on a rough surface like masonry, we
WHITE/BROWN
recommend that you seal the reader with
silicone caulking.
2. Drill a hole for the field wiring. Remove
Mounting
decorative cover from reader. Using the
Surface
reader as a template, mark the location of
the two mounting holes. Drill two 1/8" pilot
DC SIGNAL
holes for the mounting screws.
GROUND -
3. Run field wiring to reader location and feed TYPICAL INSTALLATION
BLACK
through cable hole.
RED
4. Splice the connector pigtail to field wiring.
Insert the connector into the back of the
BLACK
reader.
5. Attach the reader to the surface using the two machine screws
OUTPUT RELAY
Note: Use separate power supplies for maglock / strike
and for access control unit.
provided. These may be replaced with tamper proof screws
WHITE/BLACK
Do NOT connect Signal Ground to Earth Ground.
(customer supplied).
* Relay defaults to Normally Open.
6. Slip on the decorative cover (if used) until both tabs snap into place.
READER
WHITE/BROWN
3322328 7744
INSTALLATION OF METAL OXIDE VARISTOR
ACCESS
RELAY +
CONTROL
DC SIGNAL
UNIT RELAY -
GROUND -
BLACK
INSTALL
MOV HERE
Install the enclosed 40-volt MOV (Metal Oxide Varistor) across
Note: Use separate power supplies for maglock / strike
the relay contacts in the access control unit, as shown. The
and for access control unit.
Access Control Unit must have its own power supply.
Do NOT connect Signal Ground to Earth Ground.
* Relay defaults to Normally Open.
3322328 7744
3/4" diameter
through hole
for cables.
Mounting
Surface
Mounting Plate
Use supplied screws
3/4" diameter
through hole
for cables.
Mounting
Surface
¿
Use supplied screws
12
POWER
VDC
SUPPLY
LOCK
POWER
SUPPLY
*/
MAGLOCK
STRIKE
REMOTE OPEN
Line A GRAY
Line B VIOLET
+
12 POWER
1.74" 1.74"
EARTH
VDC
SUPPLY
GROUND
LOCK
POWER
SUPPLY
*/
MAGLOCK
STRIKE
REMOTE OPEN
LOCK
+
POWER
_
Line A GRAY
SUPPLY
Line B VIOLET
DC
MAGLOCK /
STRIKE
EARTH
GROUND
into j-box or through cable hole.
4. Attach the mounting plate to the mounting
surface or j-box with the appropriate
fasteners.
5. Splice the connector pigtail to field wiring.
Use supplied
Insert the connector into the back of the reader.
6. Attach the housing to the mounting plate by inserting the two tabs screw
inside the top of the housing into the two slots at the top of the
mounting plate.
INSTALLATION STEPS FOR RKDT-SR-S:
7. Secure by installing supplied screw into the hole at the bottom of
the reader.
1. If mounting the unit outdoors, especially on a
rough surface like masonry, we recommend
that you seal the reader with silicone caulking.
INSTALLATION STEPS FOR RKDT-SR-M
MULLION INSTALLATION DIAGRAM
2. Drill holes as needed per installation
diagram shown to the left or install a single
1. If mounting the unit outdoors, especially
gang j-box.
on a rough surface like masonry, we
3. Run field wiring to reader location and feed
recommend that you seal the reader with
into j-box or through cable hole.
silicone caulking.
4. Attach the mounting plate to the mounting
2. Drill a hole for the field wiring. Remove
surface or j-box with the appropriate
decorative cover from reader. Using the
fasteners.
3/4" Diameter hole in
reader as a template, mark the location of
5. Splice the connector pigtail to field wiring.
mounting surface for
the two mounting holes. Drill two 1/8" pilot
Insert the connector into the back of the reader.
wiring
holes for the mounting screws.
6. Attach the housing to the mounting plate by inserting the two tabs
3. Run field wiring to reader location and feed
inside the top of the housing into the two slots at the top of the
through cable hole.
mounting plate.
4. Splice the connector pigtail to field wiring.
7. Secure by installing supplied screw into the hole at the bottom of
Insert the connector into the back of the
the reader.
reader.
Mounting
3.20
¿
5. Attach the reader to the surface using the two machine screws
Surface
ET-SR-R-S / ET-SR-R-K
provided. These may be replaced with tamper proof screws INSTALLATION STEPS FOR RKDT-SR-M
(customer supplied).
6. Slip on the decorative cover (if used) until both tabs snap into place.
1. If mounting the unit outdoors, especially
TYPICAL INSTALLATION
on a rough surface like masonry, we
RED
recommend that you seal the reader with
silicone caulking.
INSTALLATION OF METAL OXIDE VARISTOR
BLACK
2. Drill a hole for the field wiring. Remove
decorative cover from reader. Using the
reader as a template, mark the location of
ACCESS
RELAY +
the two mounting holes. Drill two 1/8" pilot
CONTROL
holes for the mounting screws. UNIT
3. Run field wiring to reader location and feed
READER
through cable hole.
4. Splice the connector pigtail to field wiring.
Insert the connector into the back of the
reader.
Install the enclosed 40-volt MOV (Metal Oxide Varistor) across
5. Attach the reader to the surface using the two machine screws
the relay contacts in the access control unit, as shown. The
provided. These may be replaced with tamper proof screws
Access Control Unit must have its own power supply.
DC SIGNAL
(customer supplied).
GROUND -
6. Slip on the decorative cover (if used) until both tabs snap into place.
BLACK
.90" .90"
INSTALLATION OF METAL OXIDE VARISTOR
Note: Use separate power supplies for maglock / strike
ACCESS
20301 Nordhoff Street, Chatsworth, CA 91311
Do NOT connect Signal Ground to Earth Ground.
CONTROL
PHONE (818) 882-0020 • FAX (818) 882-7052
UNIT
* Relay defaults to Normally Open.
Website: www.securakey.com • E-mail: mail@securakey.com
3322328 7744
Install the enclosed 40-volt MOV (Metal Oxide Varistor) across
the relay contacts in the access control unit, as shown. The
Access Control Unit must have its own power supply.
Website: www.securakey.com • E-mail: mail@securakey.com
3/4" diameter
through hole
for cables.
Mounting
Surface
Use supplied screws
1.74"
+
12
POWER
VDC
SUPPLY
OUTPUT RELAY
WHITE/BLACK
+
_
RELAY -
LOCK
POWER
WHITE/BROWN
SUPPLY
MAGLOCK /
INSTALL
MAGLOCK
MOV HERE
STRIKE
STRIKE
REMOTE OPEN
Line A GRAY
Line B VIOLET
EARTH
GROUND
and for access control unit.
RELAY +
RELAY -
TOLL-FREE (800) 891-0020
INSTALL MAGLOCK /
MOV HERE
STRIKE
20301 Nordhoff Street, Chatsworth, CA 91311
PHONE (818) 882-0020 • FAX (818) 882-7052
TOLL-FREE (800) 891-0020
into j-box o
4. Attach the
surface o
3.20
¿ ¿
fasteners.
5. Splice the
Insert the c
6. Attach the
inside the
mounting p
7. Secure by
the reader.
1. If mounting
on a rough
recommend
silicone cau
2. Drill a hole
decorative c
3.20
¿
¿
reader as a
the two mou
holes for the
3. Run field wir
through cab
4. Splice the c
1.74"
.90" .90"
Insert the c
reader.
5. Attach the r
provided. T
(customer s
6. Slip on the d
INSTA
LOCK
POWER
SUPPLY
DC
*/
1.74"
1.74" .90"
Install the
the relay
Access C
LOCK
+
POWER
_
SUPPLY
DC
INSTA
ACCES
CONTRO
UNIT
.90"
Websit