Table of Contents
Advertisement
CAUTION
If burner does not light, turn knobs to
minutes, and try again. If the burner does not ignite with
the valve open, gas will continue to flow out of the burner
and could accidently ignite with risk of injury.
Match-Lighting
s Do not lean over grill while lighting.
1. Open lid.
Turn on gas at LP tank.
2.
Place lit match into match lighting stick, then into lighting hole
on left and/or right side of grill.
3.
Push in and turn far left or right burner knob to HI. Be sure
burner lights and stays lit.
4.
Light adjacent burners in sequence by pushing knobs in and
turning to HI.
Ignitor Lighting The Sideburner
s Do not lean over grill while lighting.
1.
To ignite sideburner, open sideburner cover.
2.
Turn sideburner knob to HI, push and hold ELECTRONIC
IGNITOR button.
3.
If sideburner does NOT light, turn knob to OFF, wait 5 minutes,
then repeat lighting procedure or use match.
Match Lighting
1.
To match light sideburner, open sideburner cover.
2.
Place lit match near burner.
3.
Push in and turn sideburner
knob counterclockwise.
Be sure burner lights
and stays lit.
20 • 461240504
OFF
, wait 5
Burner Flame Check
• Remove grates and flametamers. Light burner, rotate knobs
from HI to LOW. You should see a smaller flame in LO position
than seen on HI. Always check flame prior to each use.
Perform flame check on sideburner. If only low flame is seen
refer to "Sudden drop or low flame" in the
Section
.
Turning Grill Off
• Turn all knobs to
OFF
position. Turn LP tank off by turning
hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP tank.
button. "Click" should be heard and spark seen each time
between collector box or burner and electrodes. See
"Troubleshooting"
if no click or spark.
Valve Check
• Important: Make sure gas is off at LP tank before checking
valves
. Knobs lock in
OFF
push in knobs and release, knobs should spring back. If knobs
do not spring back, replace valve assembly before using grill.
Turn knobs to
LO
position then turn back to
Valves should turn smoothly.
Hose Check
•
Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory
(and should never be painted)
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces.
•
Plastic parts:
Wash with warm soapy water and wipe dry.
s
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces:
Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces:
Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces:
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad.
Troubleshooting
HI
LO
Press and hold electronic ignitor
position. To check valves, first
OFF
position.
. Apply a strong solution
To maintain your grill's high quality
Advertisement
Table of Contents
