Tascam CD-D4000 Owner's Manual
  1. Manuals
  2. Brands
  3. Tascam Manuals
  4. Disc Duplicator
  5. CD-D4000 MKII
  6. Owner's manual
Tascam CD-D4000 Owner's Manual

Tascam CD-D4000 Owner's Manual

Tascam cd duplicator owner's manual cd-d4000
Hide thumbs Also See for CD-D4000:
Table of Contents

Advertisement

Quick Links

»
CD-D4000
CD Duplicator
˛
Professional
Ü
ÿ
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons..
The exclamation point within an equilateral triangle is intended to alert the user to the pres-
Ÿ
ence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
This appliance has a serial number
located on the rear panel. Please record
the model number and serial number
and retain them for your records.
Model number
Serial number
OWNER'S MANUAL
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
9101417100

Advertisement

Table of Contents
loading

Related Manuals for Tascam CD-D4000

Summary of Contents for Tascam CD-D4000

  • Page 1 » CD-D4000 CD Duplicator ˛ Professional Ü ÿ The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons..

  • Page 2: Important Safety Precautions

    When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover. IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN. TASCAM CD-D4000 For U.S.A TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

  • Page 3: Important Safety Instructions

    (including amplifiers) that produce heat. ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H) TASCAM CD-D4000...
  • Page 4 3.2 Physical specifications...11 3.3 Dimensional drawing ...11 1.1 Installing the CD-D4000 The CD-D4000 is designed to fit into 2U of standard 19” rack space. We suggest that you leave 1U of space above the unit to allow for cooling. There are no connections to be made to and from the CD-D4000 other than the power connection on the rear panel, as the unit is completely self-contained.

  • Page 5: Power Switch

    6 SLAVE drive The SLAVE drive holds the destination CD. This must be a CD-R disc. The CD-D4000 cannot record on CD-RW discs (but can use them in the MASTER drive as source discs). The eject button is used to eject the slave disc when no operation is in progress.

  • Page 6: Basic Operations

    NOTE Do not turn off the CD-D4000 while writing to the slave disc (i.e. part of the way through a disc copy operation. If you do, the disc will be corrupt, and unusable.

  • Page 7: Disc Copy

    Do not use warped discs or discs with off-cen- ter holes with the CD-D4000. While the copy operation is in progress, make sure that the CD-D4000 is not subjected to vibration or mechanical shocks. 2 - Modes Press the MODE key until the display appears as...

  • Page 8: Possible Problems When Copying Or In Test Write Mode

    Copy is replaced by the word Test messages. At the end of the test procedure, the CD-D4000 does not simulate the writing of the TOC (the finalization process), and displays: T e s t w r i t e...

  • Page 9: Compare Cd-Rom

    Master , with a third option being to exit ( Exit P l a y N e x t t r a c k message is briefly shown and TASCAM CD-D4000...

  • Page 10: Setting The Writing Speed

    TASCAM CD-D4000 2.6 Setting the writing speed The CD-D4000 SLAVE drive is capable of writing information to a CD or CD-ROM drive at normal ), double ( ) or four times ( The writing speed is set as described below.

  • Page 11: Operational Specifications

    6.5 kg (14.3 lbs) Voltage and current USA/Canada 120 V ~ 60 Hz, 380 mA requirements: Korea 220V~ 60 Hz 220 mA Europe/UK 230 V~ 50 Hz, 220mA Australia 240 V~ 50 Hz, 220mA Power consumption 290mm 288mm TASCAM CD-D4000...
  • Page 12 » CD-D4000 TEAC CORPORATION Phone: (0422) 52-5082 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan TEAC AMERICA, INC. Phone: (323) 726-0303 7733 Telegraph Road, Montebello, California 90640 TEAC CANADA LTD. Phone: 905-890-8008 Facsimile: 905-890-9888 5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada TEAC MEXICO, S.A.

Table of Contents