Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TANDBERG Codian MSE 8321
Summary of Contents for TANDBERG Codian MSE 8321
- Page 1 Codian ISDN Gateway MSE 8321 Getting started...
- Page 2 Codian ISDN Gateway MSE 8321 Getting started...
- Page 3 All other product and company names herein may be trademarks of their respective owners. 61-00020-02 rev 01 TANDBERG Philip Pedersens vei 20 1366 Lysaker Norway Telephone: +47 67 125 125 Telefax: +47 67 125 234 Video: +47 67 117 777 E-mail: tandberg@tandberg.com www.tandberg.com...
-
Page 4: Table Of Contents
Table of contents General information ........................ 1 About the ISDN gateway ..................1 Port and LED location ....................1 LED behavior ........................ 2 Installing the ISDN gateway ....................4 Install the ISDN gateway into the MSE 8000 chassis ........4 Connecting the ISDN gateway .................... -
Page 5: General Information
General information General information About the ISDN gateway The ISDN gateway is a high performance video gateway which enables ISDN network connectivity for the Codian IP-based video infrastructure products as well as IP-based endpoints. Port and LED location Figure 1 shows the position of ports on the ISDN gateway. Figure 1: ISDN gateway front panel Compact Flash Activity LED... -
Page 6: Led Behavior
LED behavior Table 1 describes the behavior of the LEDs. Table 1: ISDN gateway LED behavior Color Indicates Compact Flash Flashing One of: Activity green the ISDN gateway is booting a configuration change has been made the configuration is being transferred by FTP Console Link Green A PC is connected to the console port... - Page 7 General information Table 1: ISDN gateway LED behavior (continued) Color Indicates Ethernet Port Status, for each Ethernet port: Green The link has been negotiated as a full-duplex link Green Packets are being transmitted on this port Link Green The speed of the link from this port, which is either 10, 100, or 1000 Mbps Power Blue...
-
Page 8: Installing The Isdn Gateway
Installing the ISDN gateway : Before installing the ISDN gateway into the MSE 8000, and IMPORTANT connecting the power supply, you must read the safety information at http://www.codian.com/safety.htm Although blades are hot-swappable parts, you must only remove one blade at any time. Remove the power from the MSE 8000, if you need to remove more than one blade at a time. - Page 9 Installing the ISDN gateway Using a No.1 Phillips screwdriver, tighten the screws in the retaining latches with a clockwise quarter turn. Figure 2: Inserting a blade into the chassis Figure 3: Closing the retaining latches on the front of a blade...
-
Page 10: Connecting The Isdn Gateway
Connecting the ISDN gateway Your ISDN connection To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord. Outside North America Check with your network provider to ensure that your incoming ISDN PRI line is terminated in an NTU/CSU (Network Termination Unit/ Channel Service Unit). If it is not, then seek their advice regarding the provisioning of such a device. -
Page 11: Initial Configuration
Initial configuration Initial configuration Step one: Configure Ethernet Port A settings The default setting for the ISDN gateway Ethernet ports is auto-sensing mode. If the switch ports to which you connect the ISDN gateway are not also set to auto-sensing mode, then you need to configure the ISDN gateway Ethernet ports to use the same speed and duplex mode. -
Page 12: Configuring The Isdn Gateway
Configuring the ISDN gateway Step one: Log in to the ISDN gateway All administration of the ISDN gateway is performed via the web interface. To log in to the ISDN gateway: Log in to the Supervisor’s web interface. Go to and click the IP address of the ISDN gateway. -
Page 13: Step Three: Configure An H.323 Gatekeeper
Configuring the ISDN gateway Step three: Configure an H.323 gatekeeper If you have H.323 endpoints, using an H.323 gatekeeper can make it easier for callers to make their call. You can configure the ISDN gateway to use an external gatekeeper or its own built-in gatekeeper. -
Page 14: Configuring The Mcu
Configuring the MCU If you are connecting the ISDN gateway to a Codian MCU, refer to this section for information. Adding the ISDN gateway To simplify the making of outgoing calls by ISDN, you can configure your MCU. To do this: Using your web browser, navigate to the web interface of the MCU. -
Page 15: Making Calls
Making calls Making calls When you have set up the Codian ISDN gateway, and MCU if appropriate, you can make calls via the ISDN network. Calling in by ISDN If you have configured the dial plan as described in Step four: Configure the dial plan on page 9, endpoints calling the telephone number of the ISDN gateway will, when the call is completely established, be forwarded to the auto attendant of the MCU. -
Page 16: Troubleshooting And Technical Support Information
Troubleshooting and technical support information Refer to this section if you are experiencing difficulties with the ISDN gateway. Ensure that you have followed the instructions in this guide when installing and configuring the ISDN gateway. Calls fail to complete If outgoing calls fail to complete, check that you have configured the MCU and ISDN gateway correctly, paying particular attention to the number you are trying to call. -
Page 17: Getting More Help
Troubleshooting and technical support information Getting more help If the documentation does not answer your question or you have a problem with one of our products: Refer to the Technical FAQ section of the web site. We keep the Technical FAQ section up to date with the latest information from our technical support team regarding the resolution of customer issues. -
Page 18: Pin Outs
Pin outs The pin numbering for the PRI ports on the ISDN gateway is shown in Figure 4. The pin assignments for the PRI ports are shown in Table 2: Table 2: Pin assignments for PRI ports Pin number Signal Receive - Receive + Not connected... - Page 19 Codian ISDN Gateway MSE 8321 Getting started...
- Page 20 61-0020-02...