Table of Contents
Related Manuals for Symbol SPT 1500
Summary of Contents for Symbol SPT 1500
- Page 2 Symbol products. Symbol is a registered trademark of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
- Page 3 Technologies to receive this document. Getting Started with the SPT 1500 Before you can use your SPT 1500, you will need to perform some basic set up procedures. First, familiarize yourself with the many parts of the SPT 1500 by reviewing the following illustration.
- Page 4 Parts of the SPT 1500 The following illustration indicates each part of the SPT 1500 Terminal. Scan Window/IR Port Scan Decode LED Left Scan Trigger Power/ Backlight Control Daily Calendar Application Button Address/Phone List Application Button Scroll Button Battery Door Latch...
-
Page 5: Installing Batteries
Q u i c k Installing Batteries Before using your SPT 1500, you must install two AAA alkaline batteries. The batteries fit behind the battery door on the back of the SPT 1500. Note: Battery life may change with different manufacturers. -
Page 6: Calibrating The Screen
If you feel resistance when replacing the battery door, make sure the door is aligned with the slots on the back of your SPT 1500, and that the batteries are firmly seated in the battery compartment. While batteries are being replaced, data is retained for ap- proximately one minute. - Page 7 Power Button Note: If necessary, adjust the contrast control located on the side of the SPT 1500 so the screen is clear and readable. 2. Remove the stylus from its storage slot on the back of the SPT 1500. 3. Tap the exact center of each target that appears on the screen with the tip of the stylus.
-
Page 8: Writing With The Stylus
Using the SPT 1500 Using the Power/Backlight Control The power button turns the SPT 1500 on and off. This button also serves as your backlight control. With the unit on, press and hold the power button for approximately 2 seconds to turn the backlight on and off. -
Page 9: Icon Descriptions
Q u i c k Tap here for letters keyboard Icon Descriptions Applications Icon Calculator Icon Menu Icon Find Icon R e f e r e n c e Tap here for numbers keyboard Tap to display a list of available ap- plications for selection. - Page 10 Scanning with the SPT 1500 The SPT 1500 has an integrated scanner which, if your unit has been configured to use scanning input, allows you to collect data by scanning bar codes. To scan bar codes with the SPT 1500: 1.
-
Page 11: Using The Laser Pointer
Q u i c k Using the Laser Pointer The SPT 1500 has a Laser Pointer application installed which allows you to use the unit as a laser pointer. The laser is emitted from the top of the unit. To use the laser pointer: 1. - Page 12 • Protect your SPT 1500 from temperature extremes. Do not leave your SPT 1500 on the dashboard of a car on a hot day, and keep it away from heaters and other heat sources. •...
-
Page 13: Troubleshooting
SPT 1500 terminal turns itself off: • Your SPT 1500 terminal is designed to turn itself off after a period of inactivity. This period can be set at one minute, two minutes or three minutes. Check the “Auto-off after” setting... - Page 14 When I tap the • Not all applications or screens have menus. Try changing to a different application. A message appears stating that your SPT 1500 terminal memory is full: • Delete unused memos and records. If necessary, you can save these records on your computer using the Save Backup Copy option that appears in the Delete dialogs.
- Page 15 Q u i c k Beamed data does not transmit: • Confirm that the SPT 1500 terminals are 5” apart, and that the path between the two devices is clear of obstacles. When receiving beamed data an out of memory message appears: •...
-
Page 16: Performing A Soft Reset
Performing a Soft Reset A soft reset tells your SPT 1500 terminal to stop what it’s doing and start over again. All records and entries stored in your SPT 1500 terminal are retained with a soft reset. After a soft reset, the Welcome to Palm III terminal screen appears followed by the General Preferences screen (to set time and date). - Page 17 (or similar object without a sharp tip) to gen- tly press the reset button. 3. When a message appears on the SPT 1500 terminal screen warning that you are about to erase all the data stored on your SPT 1500 terminal, do one of the following: a.
-
Page 18: Service Information
S P T 1 5 0 0 Service Information Before you use a terminal, it must be configured to run your applications. If you have a problem with running your terminal or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center: 1-800-659-2240 Outside North America, contact your local Symbol representative. -
Page 19: Regulatory Information
Q u i c k Regulatory Information Radio Frequency Interference Requirements This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation. -
Page 20: Laser Devices
and measurement techniques - Section 2: Electrostatic discharge immunity test. • IEC 1000-4-3(1995-03) - Electromagnetic compatibility (EMC) - Part 4:Testing and measurement techniques - Section 3: Radiated, radio-frequency, electromag- netic field immunity test. • EN 60 950 + Amd 1 + Amd 2 - Safety of Information Technology Equipment Including Electrical Business Equipment •... - Page 21 Q u i c k Scanner Labeling R e f e r e n c e ACHTUNG LASERSTRAHL. LASERKLASSE 2. NICHT IN DEN STRAHL BLICKEN. LUMIERE LASER - NE PAS REGARDER DANS LE FAISCEAU APPAREIL A LASER DE CLASSE 2. CAUTION LASER LIGHT. DO NOT STARE INTO BEAM.CLASS 2 LASER PRODUCT 630 -680nM,1 mW LASER.
- Page 22 In accordance with Clause 5, IEC 0825 and EN60825, the following information is provided to the user: ENGLISH CLASS 1 CLASS 1 LASER PRODUCT CLASS 2 LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT DANISH KLASSE 1 KLASSE 1 LASERPRODUKT KLASSE 2 LASERLYF...
- Page 23 Q u i c k GERMAN KLASSE 1 LASERPRODUKT DER KLASSE 1 KLASSE 2 LASERSTRAHLEN NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN LASERPRODUKT DER KLASSE 2 HEBREW ITALIAN CLASSE 1 PRODOTTO AL LASER DI CLASSE 1 CLASSE 2 LUCE LASER NON FISSARE IL RAGGIOPRODOTTO AL LASER DI CLASSE 2 NORWEGIAN KLASSE 1 LASERPRODUKT, KLASSE 1...
- Page 24 For Frequently Asked Questions and tips on SPT 1500 operation, please visit the Symbol Palm website at http://www.symbol.com/palm. 70-33756-01 Revision C—September 1998 Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300...