Sony XDR-S10HDIP Operating Instructions

3-292-590-11(2)
FM/AM
Digital Radio
Operating Instructions
XDR-S10HDiP
©2008 Sony Corporation Printed in China
Owner's Record
The model number and the serial number are located on the bottom.
Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. XDR-S10HDiP
Serial No. ________________________________
For customers who purchased this product in the USA
Please register this product on line at http://www.sony.com/productregistration.
Proper registration will enable us to send you periodic mailings about new products, services, and other
important announcements. Registering your product will also allow us to contact you in the unlikely event that
the product needs adjustment or modification. Thank you.
Important Safety
WARNING
Instructions
To reduce the risk of fire or electric shock, do
1) Read these instructions.
not expose this apparatus to rain or
2) Keep these instructions.
moisture.
3) Heed all warnings.
To reduce the risk of fire, do not cover the
4) Follow all instructions.
ventilation opening of the apparatus with
5) Do not use this apparatus near water.
newspapers, tablecloths, curtains, etc. Do not
6) Clean only with dry cloth.
place the naked flame sources such as lighted
7) Do not block any ventilation openings.
candles on the apparatus.
Install in accordance with the manufacturer's
To reduce the risk of fire or electric shock, do not
instructions.
expose this apparatus to dripping or splashing,
8) Do not install near any heat sources such as
and do not place objects filled with liquids, such
radiators, heat registers, stoves, or other
as vases, on the apparatus.
apparatus (including amplifiers) that produce
Do not install the appliance in a confined space,
heat.
such as a bookcase or built-in cabinet.
9) Do not defeat the safety purpose of the
Do not expose the batteries (battery pack or polarized or grounding-type plug. A polarized
batteries installed) to excessive heat such as plug has two blades with one wider than the
sunshine, fire or the like for a long time. other. A grounding type plug has two blades
and a third grounding prong. The wide blade
As the main plug is used to disconnect the unit
or the third prong are provided for your safety.
from the mains, connect the unit to an easily
If the provided plug does not fit into your
accessible AC outlet. Should you notice an
outlet, consult an electrician for replacement
abnormality in the unit, disconnect the main plug
of the obsolete outlet.
from the AC outlet immediately.
10) Protect the power cord from being walked on
You are cautioned that any changes or
or pinched particularly at plugs, convenience
modifications not expressly approved in this
receptacles, and the point where they exit
manual could void your authority to operate this
from the apparatus.
equipment.
11) Only use attachments/accessories specified by
the manufacturer.
These following indications are located on the
12) Use only with the cart, stand, tripod, bracket,
bottom exterior of the power supply unit.
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
This symbol is intended to alert the
user to the presence of uninsulated
"dangerous voltage" within the
13) Unplug this apparatus during lightning storms
product's enclosure that may be of
or when unused for long periods of time.
sufficient magnitude to constitute a risk
of electric shock to persons. 14) Refer all servicing to qualified service
personnel. Servicing is required when the
This symbol is intended to alert the user
apparatus has been damaged in any way, such
to the presence of important operating
as power-supply cord or plug is damaged,
and maintenance (servicing) instructions
in the literature accompanying the liquid has been spilled or objects have fallen
appliance.
into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
INFORMATION
normally, or has been dropped.
™
This equipment has been tested and found to HD Radio Technology Manufactured Under
comply with the limits for a Class B digital device, License From iBiquity Digital Corp. U.S. and
™
pursuant to Part 15 of the FCC Rules. These limits Foreign Patents. HD Radio and the HD Radio
are designed to provide reasonable protection logo are proprietary trademarks of iBiquity
against harmful interference in a residential Digital Corp.
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
What is HD Radio™
installed and used in accordance with the
instructions, may cause harmful interference to
Technology?
radio communications. However, there is no
guarantee that interference will not occur in a
HD Radio Broadcasting was approved by the
particular installation. If this equipment does
Federal Communications Commission in
cause harmful interference to radio or television
October 2002 as the system for digital AM and
reception, which can be determined by turning
FM broadcasting in the U.S.
the equipment off and on, the user is encouraged
to try to correct the interference by one or more HD Radio technology features include:
of the following measures: – Static-free, clear radio reception.
— Reorient or relocate the receiving – FM Multicasting – the ability to broadcast
antenna.
multiple program streams over a single FM
— Increase the separation between the equipment
frequency.
and receiver.
– A variety of "data services, " including text-based
— Connect the equipment into an outlet on a circuit
information – artist name, song title, etc.
different from that to which the receiver is
connected. scrolled across your receiver display.
— Consult the dealer or an experienced radio/TV
– Digital broadcasts in the same frequencies as
technician for help.
analog broadcasts; listeners do not need to learn
a new station number and today's stations
remain at their current place on the dial.
HD Radio technology is developed and licensed
by iBiquity Digital Corporation and supported by
the leaders of the broadcasting, consumer
electronics and automotive industries.
What is iTunes Tagging? Specifications
The iTunes Tag button on the new XDR-S10HDiP Time display
allows you to tag songs you like that are broadcast by 12-hour system
HD Radio stations. Information about these tagged
Frequency range
songs is stored by the receiver and transferred to
Band Frequency Channel step
your iPod. When you connect your iPod to your
computer, iTunes automatically presents the songs in FM 87.5 – 108 MHz 0.1 MHz
a new Tagged playlist so you can preview, buy, and
AM 530 – 1 710 kHz 10 kHz
download them. iTunes Tagging is a great way to
Speaker
discover new music add it to your collection!
Approx. 6.6 cm (2 5/8 inches) dia. 8 Ω
Input
AUDIO IN jack (ø 3.5 mm stereo minijack)
Features
Antenna terminal
75 Ω antenna terminal for FM
 FM/AM Digital Radio with HD Radio
Antenna terminal for AM
technology and iPod / iPhone compatibility
Audio power specifications
 iTunes Tagging capability, enabling the user to
POWER OUTPUT AND TOTAL HARMONIC
save song information with the touch of a
DISTORTION
button while listening to an HD Radio station.
With 8-ohm loads, both channels driven from
 Large LCD displays HD Radio information
150-10,000 kHz; rated 3W per channel-minimum
 Stereo speakers with surround sound function
RMS, with no more than 10% total harmonic
 Fully adjustable tone control for fine tuning of
distortion.
bass and treble
 Supplied remote commander Power output
4 W + 4 W (maximum power)
Power requirements
Precautions
120 V AC, 60 Hz
Dimensions
 Play the unit on the power source specified in Approx. 330  130  135 mm (w/h/d)
"Specifications". (13  5 /  5 / inches) not incl. projecting
1 3
8 8
 To disconnect the AC power cord (mains lead), parts and controls
pull it out by the plug, not the cord.
Mass
 The unit is not disconnected from the mains as
Approx. 3.1 kg (6 lb 13.3 oz) incl. power supply
long as it is connected to the AC outlet, even if
unit
the unit itself has been turned off.
Supplied accessories
 The dating code and the nameplate are located
Remote commander (1)
on the bottom exterior of the unit.
FM wire antenna (1)
 Since a strong magnet is used for the speaker,
FM dipole antenna (1)
keep personal credit cards using magnetic coding
AM loop antenna (1)
or spring-wound watches away from the unit to
Audio connecting cable (1)
prevent possible damage from the magnet.
Universal dock adapter for iPhone (1)
 Do not leave the unit in a location near a heat
Connector cover (1)
source such as a radiator or airduct, or in a
place subject to direct sunlight, excessive dust, Design and specifications are subject to change
without notice.
mechanical vibration, or shock.
 Allow adequate air circulation to prevent
Compatible iPod models
internal heat build-up. Do not place the unit on
a surface (a rug, a blanket, etc.) or near The compatible iPod models are as follows.
materials (a curtain) which might block the Update your iPod to use the latest software before
ventilation holes. you use it.
 Should any solid object or liquid fall into the unit,
unplug the unit and have it checked by a qualified
personnel before operating it any further.
 To clean the casing, use a soft cloth dampened
with a mild detergent solution.
 Never touch the wire of the external FM iPod nano 3rd
generation (video)
antenna during a thunderstorm. Furthermore,
immediately disconnect the AC power cord
iPod classic
iPod touch
from the radio.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
Troubleshooting
iPod nano 2nd
generation iPod 5th
iPhone (aluminium) generation (video)
Should any problem persist after you have made
the following checks, consult your nearest Sony
dealer.
A broadcast is received in analog only, even
though the area is within HD Radio
reception.
iPod nano 1st
• Depending on the conditions, if the incoming
generation iPod 4th generation iPod 4th
signal strength is too weak or unstable, the HD
(color display) generation
indicator will not flash or light up. In that case,
the HD Radio broadcast will be received as an
analog signal.
The radio or iPod alarm is activated but no
sound comes on at the preset alarm time.
• Has VOLUME been adjusted?
iPod mini
There is no sound from the iPod.
The iPod models that are compatible with iTunes
• Make sure the iPod is securely connected.
Tagging are as follows:
• Adjust the VOLUME.
 iPod nano 3 rd generation
 iPod classic
The iPod cannot be operated with this unit.
 iPod 5 th generation
• Make sure the iPod is securely connected.
* The models above may vary without notice. For
The iPod cannot be charged.
the latest information, check the website of
• Make sure the iPod is securely connected.
Apple Inc.
"CANNOT DETECT" appears in the display
Notes
when connecting an iPod.
 In these Operating Instructions, "iPod" is used
• Disconnect the iPod once and then reconnect it
as a general reference for the iPod functions on
securely.
the iPod and iPhone, unless otherwise specified
by the text or illustrations.
 iTunes Tagging requires iTunes 7.4 or later.
Notes on radio reception
Connecting the
 Keep away digital music player or mobile phone
antenna from the AM loop antenna or the FM antenna,
as this may lead to interference of reception.
 When you are listening to the radio with an
To connect the AM loop
iPhone connected to the unit, interference with
radio reception may occur.
antenna
 When you are listening to the radio while
The shape and the length of the antenna is charging an iPod, interference with radio
designed to receive AM signals. Do not dismantle reception may occur.
or roll up the antenna.
1
Remove only the loop part from the
Using the connector
plastic stand.
cover
2
Set up the AM loop antenna.
To protect the connector of the unit from dust or
dirt, you can put the connector cover on.
Attaching the connector cover
Match both claws of the connector cover with the
3
Connect the cords to the AM antenna
pits inside of the connector and press the other
terminals.
side down until it clicks.
Cord (A) or cord (B) can be connected to
either terminal.
Insert the cord
while pushing
down the
terminal clamp. Removing the connector cover
Pull up the tab of the connector cover using your
finger.
4
Make sure the AM loop antenna is
connected firmly by pulling softly.
Adjusting the AM loop antenna
Find a place and an orientation that provide good
reception.
 Do not place the AM loop antenna near the
unit or other AV equipment, as noise may
result.
Tip
Adjust the direction of the AM loop antenna for
best AM broadcast sound.
To connect the FM antenna
This unit comes supplied with an FM wire
antenna and FM dipole antenna. Connect
whichever antenna that provides the best
reception to the FM antenna terminal.
FM wire antenna
(supplied)
FM dipole antenna
(supplied)
Adjusting the FM wire antenna
Be sure to fully extend the FM wire antenna, and
keep it as horizontal and vertical as possible.
Adjusting the FM dipole antenna
Be sure to fully extend the FM dipole antenna.
Align the antenna in the shape of a T and place in
a high position on a wall away from this unit.
Tip
If you have poor FM reception, use a 75 Ω coaxial
cable (not supplied) to connect the unit to an
outdoor FM antenna as shown below.
Outdoor FM antenna

Size AAA (R03)  2
iPod and VOLUME + buttons
have a tactile dot.
Preparing the remote
commander
Installing the batteries into the remote
commander (See Fig. )
Insert two size AAA (R03) batteries (not
supplied).
When to replace the batteries
With normal use, the batteries should last for
about six months. When the remote commander
no longer operates the unit, replace all the
batteries with new ones.
Notes
• Do not charge dry batteries.
• When you are not going to use the remote
commander for a long time, remove the
batteries to avoid any damage caused by leakage
and corrosion.
Using the remote
commander
Common buttons that appear on both the remote
commander and the unit control the same
functions.
ALARM button
Press to set the alarm to "ON" or "OFF. "
Press and hold for 2 seconds to enter "ALARM
TIME SET. "
TONE button
To set the tone directly.
HD SCAN button
The selected band is scanned, and receivable HD
Radio stations are played for 3 seconds in order of
frequency.
SCAN button
The selected band is scanned, and receivable
radio stations are played for 3 seconds in order of
frequency.
BRIGHT button
To adjust the brightness of the display.