Related Manuals for Sony CCU-D50P
Summary of Contents for Sony CCU-D50P
-
Page 1: Camera Control Unit
Camera Control Unit Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. CCU-D50 CCU-D50P 2002 Sony Corporation 3-620-535-12(1) - Page 2 Owner’s Record The model and serial numbers are located at the rear. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. ______________ Serial No. _________________ Important Safety Instructions •...
- Page 3 For the customers in Europe (CCU-D50P only) This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the...
-
Page 4: Table Of Contents
Table of Contents Overview ... 5 Features ...5 Using the CD-ROM Manual ... 6 Available Functions Depending on the Device Connected to the Unit ... 7 Camera Cable Length... 8 Rack Mounting ...8 Connections ... 9 Connections for transmitting digital video (SDI) signals between this unit and a camera ... -
Page 5: Overview
CA-D50, the ROM of the camera must be replaced. For more information about checking the version and exchanging ROMs, contact your Sony dealer or a Sony service representative. Camera Serial number... -
Page 6: Using The Cd-Rom Manual
If you lose the CD-ROM disc or become unable to read its content, for example because of a hardware failure, contact a Sony service representative. • Netscape Navigator is a registered trademark of Netscape Communications Corporation in the U.S. and other countries. -
Page 7: Available Functions Depending On The Device Connected To The Unit
Available Functions Depending on the Device Connected to the Unit The following explains the types of signals which can be output and the functions which are available depending on the device connected to this unit. Output signals Device connected to the unit DXC-D35/D35P/D35WS/D35WSP camera + CA-D50 camera adaptor DXC-D35/D35P/D35WS/D35WSP camera + CA-537/537P... -
Page 8: Camera Cable Length
150 m (about 492 feet). Rack Mounting The unit can be mounted in a standard 19-inch studio rack with the supplied mounting brackets. For more information about rack mounting, contact your Sony dealer or a Sony service representative. Rack mounting brackets (supplied) -
Page 9: Connections
Connections The following provides examples of how to connect other devices to this unit. Notes • Be sure to power this unit off before connecting or disconnecting camera cables. When using one CCU-D50/D50P unit Input Input Output Control console Input Input a) SDI, Y/ R–Y/B–Y and R/G/B are... - Page 10 Overview When using two CCU-D50/D50P units Prompter signal Return video signal Reference sync signal CCU-D50/D50P Camera Control Unit VCR, chroma keyer, etc. Switcher, video monitor, etc. a) SDI, Y/ R–Y/B–Y and R/G/B are enabled by system setting DIP switches on the front panel, and by cabling changes on the SDI unit (see pages 11 and 18) .
-
Page 11: Connections For Transmitting Digital Video (Sdi) Signals Between This Unit And A Camera
Connections for transmitting digital video (SDI) signals between this unit and a camera In a system consisting of this unit, a DXC-D35/D35P/ D35WS/D35WSP camera, and CA-D50 Camera Adaptor, digital video (SDI) signals can be transmitted between this unit and the camera. Connections for transmission over CCZ cable (max. - Page 12 Overview Note Be sure to power this unit off before proceeding to the following operation. Remove the two screws and gently pull the SDI unit out. Note Be careful not to pull the SDI unit out too far. Doing so may disconnect or damage the connectors.
- Page 13 Connections for transmission over RG cable (6/U or 6A/U) (max. length 200 m (656 feet)) CCZ-An camera cable RG cable (6/U or 6A/U), max. length 200 m (about 656 feet) CAMERA SDI IN SDI OUT Switcher, video monitor, VCR, etc. Check that the cabling in the SDI unit of this unit is set to VBS mode, and that digital transmission is turned off with the system setting switches.
-
Page 14: When Using The Rm-M7G Remote Control Unit
Overview When Using the RM-M7G Remote Control Unit The RM-M7G Remote Control Unit can be connected directly to this unit. When this unit is powered on, it is set up to control the camera/camcorder. If you have connected an RM-M7G, do the following to set up this unit and the RM-M7G for control from the RM-M7G. -
Page 15: Location And Functions Of Parts
This unit is equipped with a cooling fan. If the fan should fail, this indicator flashes in red. Power the unit off immediately and contact your Sony dealer or a Sony service representative for repair. Continuing to use the unit with a malfunctioning fan may shorten the life of this unit. - Page 16 Location and Functions of Parts 3 PANEL ACTIVE button When the camera/camcorder connected to this unit is being controlled remotely by a remote control unit such as the RM-M7G, pressing this button causes the button to light up and assumes control of the camera/ camcorder from this unit.
- Page 17 WHITE (white balance automatic adjustment) button Adjusts the white balance automatically when the WHITE/BLACK BALANCE switch is set to AUTO or PRESET. This button lights when adjustment starts, and goes off if adjustment is completed successfully. If adjustment could not be completed successfully, this button flashes for eight seconds at an intervals of about 0.5 seconds.
- Page 18 Location and Functions of Parts Not lit: The unit is not in digital transmission mode (factory default setting). qd AUTO IRIS button Selects the iris adjustment mode. Before using this button, set the IRIS switch on the camera/camcorder to AUTO. OFF (not lit): Manual adjustments can be made with the IRIS knob.
- Page 19 The intercom system may not operate correctly if this switch is set to another mode. For more information about intercom system connections, contact your Sony dealer or a Sony service representative. qk MENU section MENU button ENTER button...
- Page 20 Location and Functions of Parts ql SHUTTER adjustment section SHUTTER SPEED/CABLE LENGTH display window SHUTTER SHUTTER SPEED/CABLE LENGTH SHUTTER CLEAR SCAN SHUTTER buttons SHUTTER switch SHUTTER switch Selects whether or not to use electronic shutter. SHUTTER: Turns the normal shutter function on. OFF: Do not use the shutter function.
-
Page 21: Rear Panel
Rear Panel 1 VBS OUTPUT 1 and 2 connectors 2 S VIDEO connector 3 Y/G/Y, R–Y/R/C, B–Y/B connectors OUTPUT OUTPUT S VIDEO Y/G/Y R-Y/R/C B-Y/B MONITOR SYNC OUTPUT OUTPUT qd Spare connector qf SYNC OUTPUT connector qg MONITOR OUTPUT connector 1 VBS OUTPUT (composite video output) 1 and 2 connectors (BNC type) Output composite video signals. - Page 22 OUT connector is terminated automatically when nothing is connected to it. qd Spare connector This is a spare connector, not currently used. Description Contact your Sony dealer or a Sony service representative. ON: Gnd OFF: Open 4-wire talk, 0 dBu...
- Page 23 qf SYNC OUTPUT connector (BNC type) Outputs a sync signal from the camera/camcorder. qg MONITOR OUTPUT connector (BNC type) Outputs composite video signals for a monitor. When you press the MENU button and the SELECT up and down buttons on the front panel of this unit, information about system settings is superimposed over the video signals output from this connector.
-
Page 24: Displaying And Changing Settings
Displaying and Changing Settings Displaying Settings When the MENU button on the front panel is unlit, the SELECT up and down buttons can be used to display automatic adjustment items and the current state of the CCU-D50/D50P on a monitor connected to the MONITOR OUT connector. - Page 25 Displaying and Changing Settings Page 3 System Setting page Page 3 displays the current settings of the system including this unit, made by the system setting switches and intercom setting switches (see page 19) on the front panel of this unit. *System Setting* COMMAND MODE RETUREN...
-
Page 26: Changing Settings
Description CA SDI PLL status 200 m (656 feet) cable compensation setting Return signal mode SKIN-GATE MIX function setting Output mode setting Changing Settings When the MENU button on the front panel is lit, a menu appears on the monitor connected to the MONITOR OUT connector, allowing you to change the settings of the system including this unit. - Page 27 Displaying and Changing Settings Page 2: Volume PRESET page This page allows you to set the control values for the center click positions of the knobs on the front panel of this unit to 0 or to the factory default values. *Volume PRESET* RESET DETAIL...
-
Page 28: Notes On Use
Notes on Use Use and storage locations Avoid using or storing the unit in the following places: • Where it is subject to extremes of temperature. • Near a heat source, such as a radiator or an air duct, or in a place subject to direct sunlight. (Note that in summer the temperature in a car with the windows closed can reach 50°C (122°F).) •... -
Page 29: Specifications
Specifications General Power requirements CCU-D50: 100 to 120 V AC, 60 Hz CCU-D50P: 220 to 240 V AC, 50 Hz Power consumption CCU-D50: 1.7 A (entire system operating, 100 to 120 V AC) CCU-D50P: 0.8 A (entire system operating, 220 to 240 V AC) -
Page 30: Specifications
Extension connector for CCZ-A series camera cable CCZZ-1B (fixed on wall), CCZZ- Design and specifications are subject to change without notice. If you wish to use the INTERCOM/TALLY/AUX connector, be sure to consult your Sony dealer or a Sony service representative. - Page 31 Sony Corporation...