ADT SafeWatch 3000 Battery Replacement Instructions
Residential control panels
Hide thumbs
Also See for SafeWatch 3000:
- User manual (57 pages) ,
- Installaton manual (88 pages) ,
- Programming manual (16 pages)
Advertisement
Quick Links
www.adt.com
BATTERY REPLACEMENT INSTRUCTIONS
®
For SafeWatch
DSC 1555 and DSC 1616 Residential Control Panels
The ADT SafeWatch
have a backup battery designed to supply power to the security system during a
limited power outage. The battery, much like a car's battery, must be replaced from
time to time due to age and usage. The backup battery needs to be replaced when
the keypad displays a "BAT" or "SYSTEM LO BATTERY" message.
In most cases you can replace the battery yourself, typically saving you time and
money. The process requires the removal of two wires from the old battery and
reconnecting the same wires to the new battery. Before replacing the battery, please
read these instructions carefully, including the Battery Safety Warning instructions
below.
This section on Battery Safety should be read in its entirety and its contents understood before
handling or using a rechargeable sealed lead‐acid battery.
•
Due to the potential energy stored in a sealed lead‐acid battery, improper handling or use of
the battery or failure to observe the precautions listed in this document may result in bodily
injury caused by electrolyte leakage, heat generation or explosion.
•
USE ELECTRICALLY INSULATED TOOLS. Use of un‐insulated tools may cause a short circuit
and the heat or sparks generated by the short circuit can result in burns, damage to the
battery, or an explosion. Metallic tools may be insulated using vinyl or electrician's tape.
•
When unpacking the battery, make sure to handle it gently. Rough handling may shock the
battery, causing damage. Check that the battery is free from cracks, fractures, or leakage.
•
Be extremely careful not to drop the battery to avoid the possibility of serious injury.
If at any time you feel uncertain that you can follow these instructions or want to
have the battery replaced by an ADT service technician, contact the ADT
Customer Care Department at 1-800-ADT-ASAP and schedule a service
appointment. In most cases, ADT's standard service charge will apply.
Requesting a Replacement Battery
If you choose to replace the battery yourself, contact ADT at 1-800-ADT-ASAP to have
a replacement battery sent to you or you can purchase one at a local battery supply
store. If there is a lock on the control panel door and you do not have a key, inform
the ADT Customer Care Representative and a key will be sent to you.
3000, Vista‐10, Vista‐20, Concord 4, Concord Express,
®
3000, Vista, Concord and DSC residential security systems
Battery Safety Warning
1
Advertisement
Related Manuals for ADT SafeWatch 3000
Summary of Contents for ADT SafeWatch 3000
- Page 1 In most cases, ADT’s standard service charge will apply. Requesting a Replacement Battery If you choose to replace the battery yourself, contact ADT at 1-800-ADT-ASAP to have a replacement battery sent to you or you can purchase one at a local battery supply store.
- Page 2 Battery Replacement Instructions Before replacing Before starting the battery replacement procedure: the battery • call the ADT Customer Care Department at 1‐800‐ADT‐ASAP to have your security system placed “on test” • read the Battery Safety Warning section on the previous page, and • become familiar with the battery replacement instructions. Control panel The control panel battery is located inside a control panel box similar to the one shown in the picture below. The control panel box is typically located inside a closet, basement or utility room in your home. Backup battery The backup battery could be of one of two sizes, either a 4 Ah or a 7 Ah sizes ...
- Page 3 800‐ADT‐ASAP to schedule a service call and to request that the system be “removed from test”. 3.2 Does the battery look abnormal; (Caution: Does the battery have a swollen or split case, liquid is leaking from the case, the terminals are corroded or a hot case)? • If no, go to step 4. • If yes, close the control panel door and call 1‐800‐ADT‐ASAP to schedule a service call and to request that the system be “removed from test”. 4 Disconnect the old battery. Caution: Be sure to read the Battery Safety Warning at the beginning of these instructions before ...
- Page 4 Test your security system to make sure it is working proper. Follow the instructions in the ® SafeWatch Pro 3000, Vista‐10 or Vista‐20 “User’s Guide” in the “Testing the System” section. Did you experience any issues during the system test? • If no, go to step 8. • If yes, please call ADT at 1‐800‐ADT‐ASAP to schedule a service call for a service technician to inspect your security system. Note: Testing of your security system should be conducted each week. 8 Close the control panel door and replace the screws or lock the door.