Table of Contents
Advertisement
Quick Links
Installation
Instructions
18
19
3
17
25
24
1
Kit Contents:
Ref
Part No.
Qty.
1
1733779A
1
2
1733812
2
3
2176012
5
4
1723292A
1
5
1653768A
1
6
2171011
1
7
1931335
4
8
1919381
4
9
1917356
4
10
1917372
4
11
1724025A
1
12
2105249
1
Figure 1. Contents
This kit is required when installing front-mounted
attachments.
18
17
6
22
22
2
23
Front Hole for Dozer Applications
Rear Hole for Snowthrower Applications
Description
PUSH BAR ASSEMBLY
ROD - HITCH
SAFETY CLIP
HOOK ASSEMBLY
CLAMP
SPRING, Compression
CARRIAGE BOLT, .31 X 1
WASHER
LOCKWASHER, .31
NUT - FULL .31-18
LEVER ASSY - LIFT
PIN, CLEVIS
Sub-Frame Hitch
For Prestige / 1800 / 2800 & Conquest / 1700 / 2700 Series
16
7
5
20
3
Ref
Part No.
Qty.
13
1722469
1
14
1722819
1
15
1960033
1
16
1722946
1
17
8031007
2
18
1928721
2
19
1723115
1
20
1723309
1
21
1723795A
1
22
1960074
2
23
1921210
4
24
1928352
4
25
1733814A
1
1
Mfg. No. 1695195
12
11
3
4
14 13
Hydraulic
15
Lift
8
9
10
21
Manual Lift
(
Add to early models
already present on
current models)
Description
LOCKDOWN, HYD.
PIN, CLEVIS
CLIP, HAIRPIN
ROD, LIFT
SET, COLLAR
SCREW, .31-18 X .50
GUIDE ASSY., ROD
ROD, HITCH
BAR, LIFT
CLIP
SCREW, .38-16 X 1
NUT, FLG, .38-16
PUSH BAR LATCH
Advertisement
Table of Contents
Related Manuals for Snapper 1695195
Summary of Contents for Snapper 1695195
- Page 1 1722819 1960033 1722946 8031007 1928721 1723115 1723309 1723795A 1960074 1921210 1928352 1733814A Sub-Frame Hitch Mfg. No. 1695195 14 13 Hydraulic Lift Manual Lift Add to early models already present on current models) Qty. Description LOCKDOWN, HYD. PIN, CLEVIS CLIP, HAIRPIN...
-
Page 2: Initial Assembly
Installation Instructions NOTE: Please read through these instructions and the instructions of any other attachments before beginning installation. WARNING Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). INITIAL ASSEMBLY Assemble Hitch 1. - Page 3 Sub-Frame Hitch Figure 5. Lift Lock Plate - Hydraulic Lift Models A. Lift Cylinder B. Flat Head Pin (Original) C. Flat Head Pin (New) D. Lock Plate E. Hair Pin Clips F. Lift Shaft Assy. G. Washers Install Downward Pressure Lock HYDRAULIC LIFT MODELS 1.
-
Page 4: Install Hitch
Installation Instructions Figure 7. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod Install Hitch 1. Slide the hitch under the tractor. 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. -
Page 5: Install Lift Rod
Sub-Frame Hitch Install Lift Rod 1. Slide the lift lever (A, Figure 8) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. -
Page 6: Normal Installation
Installation Instructions Figure 10. Normal Installation & Removal REMOVAL NOTE: After removing components, reinstall the clevis pins and clips to prevent loss. 1. Disconnect the lift rod from the attachment and lift lever (C, Figure 10). 2. Remove the clevis pin and clip from the lift lever (C) and remove the lift lever. -
Page 7: Lift Variations When Using Attachments
Sub-Frame Hitch Figure 11. Lift Lock Plate - Hydraulic Lift Models A. Lift Cylinder B. Flat Head Pin (Original) C. Flat Head Pin (New) D. Lock Plate E. Hair Pin Clips F. Lift Shaft Assy. G. Washers LIFT VARIATIONS WHEN USING ATTACHMENTS When a front-mounted attachment such as a snowthrow- er or dozer blade is used with the tractor, the lift mecha-... - Page 8 Installation Instructions DOWNWARD PRESSURE LOCK PLATE - OBSOLETE Note: The following information applies only to models produced before October of 2002. It is being included here for reference pur- poses ONLY. MANUAL LIFT MODELS 1. Rest the back of the lock plate (G, Figure 4) against the spacer (I) and rotate until it lines up with the hole in the lift bar (F).