Advertisement
Quick Links
i ;
KIT PARTS
Mount to top
support
bracket.
F i igure 1. Kit Parts
Description
A Harness Assy..
8 Switch, Electric
C Wire, Switch to Ground
D Lockwasher
E Power Lift Assy.
F Clamp, Insulated
G Connectors, Self-Stripping
H Wire, Switch to Ignition
I
Wire, Switch to Lift
J Wire, Switch to Lift
K Decal, Lift Switch
L Rod Assy.,
Lift
M Arm Assy..
lift
Part No.
Item
1702082
1
171883
1
171868
1
1817366
4
1
1667764
S
826818
1
1606761
1
1702075
1
1702077
1
1702076
1
1
1669833
1701680
1
1701808
INSTALLATION., ~-
For use with a// mounted attachments
on 6500/1800
Used for rear attachments
Description
N Pin, Quick
0 Hub Assy..
Wheel
P Link, Actuator
Bracket,
Actuator,
Front
5/16-18x 1
u Spacer
W Capscrew, Hex Hd..
MFG. NO. 1691531
Series Tractors
Mount to
ignition
wire.
Part No.
1 9 6 0 0 3 3
3
1 7 0 1 9 1 4
1701881
1
102004
2
1 9 1 7 3 7 2
4
1 7 0 1 8 7 8
1
1 9 2 1 3 3 3
4
1 6 6 5 6 9 9
3
1 8 2 3 3 6 2
1
1 9 2 5 8 9 2
FORM 1702100
IN U.S.A.
882
Advertisement
Related Manuals for Snapper 1691531
Summary of Contents for Snapper 1691531
- Page 1 6/16-18 W Capscrew, Hex Hd.. 1701680 5,‘16-18 1701808 .- 1, INSTALLATION., ~- ~~~~~ INSTRUCTIONS ELECTRlC L//=T KIT MFG. NO. 1691531 on 6500/1800 Series Tractors Mount to ignition wire. Used for rear attachments onlv. Use item Q for mowers. FRONT Part No.
-
Page 2: Installation
WARNING Before installing the kit or making any adjustments: disengage the PTO; set the parking brake; stop the engine and remove the key. WARNING When disconnecting the battery cables, always disconnect the negative cable first. W h e n connecting cables, always connect the negative cable last. -
Page 3: Switch Installation
Figure 3. Cylinder ~lnstallation A. Cylinder 6. Lugs c. 4-l/2” Capscrew D. 1” Capscrew (from inside out) 12. Remove the manual lift lever as follows: a. Remove the two capscrews and lockwashen (B, figure 4). Leave the retaining nuts in place. b. - Page 4 F i g u r e 6 . T r a c t o r D a s h A . W o o d B l o c k : 6. H a m m e r C . S c r e w s ) 17., Pry off the throttle control knob by using a claw hammer and block of wood as shown in figure 6.
- Page 5 Figure 8. Upper UaSn 29. Align the steering wheel and push down onto shaft. 30. Reinstall capscrew (C, figure 7), flat washers, and locknuts to secure steering wheel. Torque nut to 10 ft. Ibs. 31. Reconnect throttle cable to engine and position under manifold capscrew and washer.
- Page 6 / .-. 1 \ ! ‘ 1 Align with holes In rlght hand side of axle support; wrapper - two places (remove bolts and reinstall If necessary). :---m ----I f ,’ CUTOU’r (TEMPLATE ONLY) ON DOTTED LINE. ’ Align with holes In rlght “hand side of axle support wrapper - two places (remove bolts and...