Page of 19
Download Bookmark Comment

Schneider Electric SMART-UPS 990-2689E User Manual

Smart inventions, inc. power supply user manual.
®
Smart-UPS
RT
Uninterruptible Power Supply
SURT 8000/10000 VA
200-240 VAC
Tower/Rack-Mount 6U
English
2010 APC by Schneider Electric. APC, the APC logo, Smart-UPS and PowerChute are owned by Schneider Electric
Industries S.A.S., American Power Conversion Corporation, or affiliated companies. All other trademarks are the property of
their respective owners.
990-2689E
05/2010

   Related Manuals for Schneider Electric SMART-UPS 990-2689E

   Summary of Contents for Schneider Electric SMART-UPS 990-2689E

  • Page 1

    ® Smart-UPS Uninterruptible Power Supply SURT 8000/10000 VA 200-240 VAC Tower/Rack-Mount 6U English  2010 APC by Schneider Electric. APC, the APC logo, Smart-UPS and PowerChute are owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation, or affiliated companies. All other trademarks are the property of their respective owners.

  • Page 3

    Introduction ® The APC by Schneider Electric Smart-UPS supply (UPS) that provides protection for electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from utility line power. The UPS provides continuous power from the internal battery until utility power returns to safe levels or the battery is fully discharged.

  • Page 4

    Hardwiring Wiring must be performed by a qualified electrician. Install a utility circuit breaker in accordance with local electrical codes (see tables below) for input wiring. Switch the UPS input circuit breaker (see A) and utility circuit breakers OFF. Remove the access panel (see B). Remove circular knockouts.

  • Page 5

    XLI model only: For three-phase input, set the Input Phase Selector switch (see C) to ‘3’. For single-phase input, leave switch in default position of ‘1’. Switch the circuit breakers ON. Check line voltages. 10. Replace the access panel. XLT/XLJ/XLTW M ODELS XLI M ODEL...

  • Page 6

    Installing and Connecting the Batteries and Attaching the Front Bezel...

  • Page 7

    ONNECTING OWER AND Hardwire the UPS (see Hardwiring). Connect equipment to the UPS (cables not included for XLT/XLJ/XLTW models). Turn on all connected equipment. To use the UPS as a master on/off switch, be sure that all connected equipment is switched ON. Press the button on the front panel to power up the UPS.

  • Page 8

    ASIC ONNECTORS Power management software and interface kits can be used with the UPS. Serial Port Use only interface kits supplied or approved by APC. Connect the UPS to the network. (Located on the Network Management Card.) Ethernet Port The optional Emergency Power Off (EPO) feature allows connected loads to be immediately de-energized from a remote location, without switching to battery operation (see EPO Option).

  • Page 9

    PERATION Indicator Description The UPS is drawing utility power and performing double conversion to supply Online power to connected equipment (see Troubleshooting). The UPS is supplying battery power to the connected equipment. On Battery The UPS is in bypass mode, sending utility power directly to connected equipment. Bypass Bypass mode operation is the result of an internal UPS fault, an overload condition or a user initiated command either through an accessory or the manual bypass...

  • Page 10

    Feature Function Manually switch connected equipment to bypass mode, so that utility power is Normal /Bypass sent directly to connected equipment. Battery operation is not available while the UPS is in bypass mode. (See Troubleshooting.) This is not a normal condition. Cold Start Supply immediate battery power to the UPS and connected equipment (see Troubleshooting).

  • Page 11

    ONFIGURABLE ETTINGS ARE MADE THROUGH SUPPLIED OPTIONAL UNCTION Automatic Self-Test Every 14 days (336 hours) UPS ID UPS_IDEN Date of Last Battery Manufacture Date Replacement Minimum Capacity 0 percent Before Return from Shutdown Alarm Delay After 5 second delay Line Failure Shutdown Delay 20 seconds Duration of...

  • Page 12

    ETTINGS ARE MADE THROUGH SUPPLIED OPTIONAL UNCTION High Bypass Point +10% of output voltage setting Low Bypass Point -30% of output voltage setting Output Voltage XLJ models: 200 VAC XLT models: 208 VAC XLTW models: 220 VAC XLI models: 230 VAC Output Frequency Automatic (50 ±...

  • Page 13

    EPO (Emergency Power Off) Option The output power can be disabled in an emergency by closing a switch connected to the EPO. Adhere to national and local electrical codes when wiring. The switch should be connected in a normally open switch contact. External voltage is not required; the switch is driven by 12V internal supply.

  • Page 14

    Terminal Mode to Configure UPS Parameters Terminal Mode is a menu driven interface that enables enhanced configuration of the UPS. Connect the serial cable to the serial port on the back of the UPS. Open a terminal program. Example: HyperTerminal •...

  • Page 15

    The battery module(s) may remain in the UPS. Shut down and disconnect any equipment attached to the UPS. Shut down and disconnect the UPS from the power supply. Unplug the battery connectors. For shipping instructions contact APC at the Web site, www.apc.com.

  • Page 16

    Press the button once to power the UPS and the connected equipment. Check that the power cable from the UPS to the utility power supply is securely connected at both ends. Check the utility power supply to ensure proper voltage at the receptacle.

  • Page 17

    ROBLEM AND OSSIBLE AUSE BYPASS ILLUMINATES The bypass switch has been turned on manually or through an accessory. FAULT AND OVERLOAD S ILLUMINATE The UPS has ceased sending power to connected equipment. FAULT ILLUMINATES Internal UPS fault. REPLACE BATTERY ILLUMINATES Replace Battery LED flashes and a short beep is emitted every two seconds to indicate the battery is...

  • Page 18

    Service If the UPS requires service do not return it to the dealer. Follow these steps: Review the problems discussed in the Troubleshooting section of this manual to eliminate common problems. If the problem persists, contact APC Customer Support through the APC Web site, www.apc.com.

  • Page 19

    ADIO REQUENCY This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

Comments to this Manuals

Symbols: 0
Latest comments: