HEX CAPSCREW CARRIAGE .~,@--: LOCKWASHER PLAIN WASHER HEX CAPSCREW Shown below are actual size heads for standard screw sizes. Example: a l/4 screw has 7/16 head and thus requires a 7/16 wrench. To measure length, use the scale below. 00000 314”...
Table of Contents STANDARD FASTENER IDENTIFICATION CHART ... SAFETY RULES General ... 2 Preparation ... 2 Operation ... 2 PARTS ILLUSTRATION ... 3 ASSEMBLY..4 INSTALLATION..5 REMOVAL ... 8 OPERATION AND NORMAL CARE Transporting ... 8 Operation On Slopes ... 8 Dozing and Snow Plowing ...
*Do not allow others near the snow/dozer blade while it is being used. *Use the snow plow/dozer blade only in daylight, or good artificial light. *Always lower the snow plow/dozer blade com- pletely to the ground when leaving it unattended to prevent it from being accidentally lowered and causing injury.
42” Snow Plow/Dozer Blade ASSEMBLY 1. Place the blade on a flat surface. 2. install two bar stops (A, figure 2) using the two 5/l 6-l 8 x 1” taptite’screws (B). 3: Insert eyebolt (A, figure 3) thru.iug on blade and screw on 5/16 nut (B) only far enough so that it is flush with the end of the eyebolt.
(in the bracket) are toward the front. 4.Attach the push bar to the bracket, using the two 3/8-16x 2-l/4 capscrew (H) and 3/8 locknuts (I) provided. 42” Snow Plow/Dozer Blade (B), two 5/16 Figure 4. Chain A. Chain B. Capscrew C.
Page 8
42” Snow Plow/Dozer Blade 5. Raise the push bar and hook up the spring (A, fig- ure 6) in location B or C as follows: Location Tractor (Series) 4000,5000,500,600, 12LT. 12RT. Resent 6000,800, 16GTH, 17GTH 6. Lower the push bar and tighten the capscrew and nut which hold chain to tractor frame.
Page 9
Figure 7. Dozer Blade Assembled and Installed A. Push Bar B. Pivot Frame C. King Pin Figure 8. A. Rod Guide B. Lift Arm (Push Bar) C. Outer Spring Clip D. Inner Spring Clip 42” Snow Plow/Dozer Blade D. Spring Clip E. Pivot Pin...
42” Snow Plow/Dozer Blade REMOVAL 1. Lower the blade, 2. Remove blade and lii rod from push bar. 3. Raise push bar and unhook the spring (A, figure 6) from the chain. 4. Disconnect the lift rod from the lift lever on tractor by removing the spring clip.
Moving the rear set collar toward the front will increase blade down pressure. 42” Snow Plow/Dozer Blade igure 9. ,. Wear Plate . Carriage Bolt, 3/9-16 x 1 Lockwasher Figure 10.
Spring Tension This snow plow/dozer blade is spring loaded so that when the blade strikes a solid object, the springs will allow the blade to release as shown in figure 12 rather than cause damage.
Page 15
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE SAE GRADE R h/Lb. FtJLbs. a-32 8-38 lo-24 lo-32 w-20 114-28 S/18-18 5118-24 318-18 318-24 7118-14 7118-20 l/2-13 l/2-20 9118-12 9118-18 5/a-ii 518-18 314-10 314-18 7/a-9 7/8-14 1-12 NOTE: 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews.
Page 16
SIMPLICITY SIMPLICITY MANUFACTURING, MANUFACTURING, INC. INC. 500 N. Spring Street 500 N. Spring Street Port Washington, Wi 53074 Port Washington, Wi 53074 FORM 1709932 FORM 1709932 PRINTED IN U.S.A. PRINTED IN U.S.A. 3/94-IPS 3/94-IPS...