Advertisement
Quick Links
© Panduit Corp. 2007
READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING
1. COMPONENT IDENTIFICATION
1.1
JACK ASSEMBLY
Jack Cap
3.0mm Crimp
Sleeves
2.0mm/1.6mm
Crimp Sleeves
Jacketed
Boot
FJJGS9C and FJJGM5C includes 3.0mm crimp sleeves
FJJGS2.0C and FJJGM2.0C includes 2.0mm/1.6mm crimp sleeves
1.2
JACKETED STRIPPING DIMENSIONS
IMPORTANT! Due to printing variations, use a rigid
scale for both jack and plug stripping dimensions,
or the appropriate PANDUIT laminated template.
1.3
900µm BUFFERED STRIPPING DIMENSIONS
IMPORTANT! Due to printing variations, use a rigid
scale for both jack and plug stripping dimensions,
or the appropriate PANDUIT laminated template.
For Technical Support: www.panduit.com/resources/install_maintain.asp
M
-C
INI
Part Numbers: FJJGM5C, FJJGM2.0C, FJEPGM5C, FJEPGM2.0C, FJJGS9CBUY,
INSTALLATION INSTRUCTIONS
REFER TO WEB SITE BELOW FOR MOST CURRENT INSTRUCTIONS
JACK
Dust Cover
Jack Housing
Ferrule
Assemblies
900µm Buffered Boot
O
-J
OM
PTI
ACK
Field Polish Termination - Singlemode and Multimode
FJJGS2.0CBUY, FJEPGS9CBUY, FJEPGS2.0CBUY
1.4
PLUG ASSEMBLY
2.0mm/1.6mm
Crimp Sleeves
Jacketed
Boot
FJEPGS9C and FJEPGM5C includes 3.0mm crimp sleeves
FJEPGS2.0C and FJEPGM2.0C includes 2.0mm/1.6mm crimp sleeves
1.5
JACKETED STRIPPING DIMENSIONS
IMPORTANT! Due to printing variations, use a rigid
scale for both jack and plug stripping dimensions,
or the appropriate PANDUIT laminated template.
The plug side is not intended to be terminated using
900µm buffered fiber.
Page 1 of 8
FJ Fiber Optic Connectors
PN256D
PLUG
Ferrule
Assemblies
Plug Insert
Dust Caps
Plug Housing
3.0 mm Crimp
Sleeves
Advertisement
Related Manuals for Panduit FJJGM2.0C
Summary of Contents for Panduit FJJGM2.0C
- Page 1 FJ Fiber Optic Connectors Field Polish Termination - Singlemode and Multimode Part Numbers: FJJGM5C, FJJGM2.0C, FJEPGM5C, FJEPGM2.0C, FJJGS9CBUY, FJJGS2.0CBUY, FJEPGS9CBUY, FJEPGS2.0CBUY INSTALLATION INSTRUCTIONS PN256D © Panduit Corp. 2007 READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING REFER TO WEB SITE BELOW FOR MOST CURRENT INSTRUCTIONS 1.
- Page 2 Check “Used By” date on bottle to ensure best performance. WARNING: The recommended primer (PANDUIT Part #FJPMR) may contain acetone. The primer is harmful if inhaled or swallowed. In case of contact with eyes or skin, flush with water. Get medical attention in case of ingestion or contact with eyes.
- Page 3 3.1.1 3.0mm/2.0mm/1.6mm JACKET / 900µm BUFFER STRIPPING Refer to Page 1 or appropriate PANDUIT laminated tem- plate for stripping dimensions. 3.2.1 For jacketed duplex cable: Split the two cables approximately 6" (152mm) or as needed depending on desired jacket stripping length.
- Page 4 PN256D 3.2.8 Repeat for the second fiber. BUFFER STRIPPER GUIDELINES: • PANDUIT recommends that you remove no more than 1/4" (6.4mm) of buffer at a time to avoid breaking the fiber. Refer to cable manufacturer’s buffer stripping guidelines for specific recommendations.
- Page 5 Edge ferrule should be visible when viewed through the Crimp die FLOUPEX10 Eye Loupe. 3.4.6 pocket 3.5.2 Repeat for the second ferrule assembly. 2. PULL FIBER 1. SCORE 3.5.1 For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 8...
- Page 6 4.11 For singlemode only: Clean the ferrule with a distilled water D= Unacceptable. Fiber has shattered. soaked wipe. Do not use alcohol to clean after using the Reterminate. .05µm lapping film. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 8...
-
Page 7: Jack Assembly
Note: If you are using O Keyed connectors, verify that plug mates with intended jack. SLIDE FJJGM5CWBL FJEPGM5CWBL FORWARD FJJGM5CXRD FJEPGM5CXRD FJJGM5CYOR FJEPGM5CYOR FJJGM5CZYL FJEPGM5CZYL For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 8... -
Page 8: Plug Assembly
Immediately after assembly, place the black dust caps over the ferrule ends. Housing Boot Hood Housing Latch Dust Caps E-mail: For Instructions in Local Languages cs@panduit.com and Technical Support: Fax: www.panduit.com/resources/install_maintain.asp www.panduit.com (708) 444-6993 Page 8 of 8...