Siemens SINUMERIK 840C Installation Instructions Manual page 428

12.93
96
Default value
101
Note:
This machine data is not included in the machine data lists. During start-up in machine data
dialog, the machine data is set or altered as appropriate via the configuration setting.
Input of code number for the motor used. The relevant motor data are stored in the software
and are transferred to machine data MD 159 to MD 175 when the motor code number is
changed. If individual motor data (MD 159 to MD 175) must be changed, then the value 99
(non-Siemens motor) must be entered as the motor code number.
Table of motors:
Order No.
1PH6101-4NF4- x
1PH6101-4NG4- x
1PH6103-4NF4- x
1PH6103-4NG4- x
1PH6105-4NF4- x
1PH6105-4NG4- x
1PH6107-4NF4- x
1PH6107-4NG4- x
1PH6131-4NF4- x
1PH6131-4NG4- x
1PH6133-4NF0- x
1PH6133-4NF4- x
1PH6133-4NG4- x
1PH6135-4NF0- x
1PH6135-4NF4- x
1PH6135-4NG4- x
1PH6137-4NF4- x
1PH6137-4NG4- x
1PH6138-4NF0- x
1PH6138-4NF4- x
1PH6138-4NG4- x
1PH6161-4NF0- x
1PH6161-4NF4- x
1PH6161-4NG4- x
©
Siemens AG 1992 All Rights Reserved
SINUMERIK 840C (IA)
Motor code number motor 1
Lower input limit
99
Rated Rated
speed power
n in P in kW
rated rated
rev/min
1500 3.7
2000 4.7
1500 5.5
2000 7.0
1500 7.5
2000 9.5
1500 9.0
2000 11.5
1500 9.0
2000 12.0
1500 11.0
1500 11.0
2000 14.5
1500 15.0
1500 15.0
2000 20.0
1500 18.5
2000 24.0
1500 22.0
1500 22.0
2000 28.0
1500 22.0
1500 22.0
2000 28.0
6FC5197- AA50
7 Drive Machine Data (SIMODRIVE Drive MD)
7.1.2 MSD MD (data description - SW 3)
Upper input limit
332
Rated No-load
current current
in A in A
rated 0
(for T (for T
=100 K) =100 K)
12.5 6.2
13.7 6.9
17.9 9.1
19.4 9.9
22.5 11.5
25.3 13.1
26.9 14.2
29.8 15.6
27.2 11.7
32.1 13.6
26.7 11.5
31.3 13.4
37.5 16.1
35.0 16.1
41.3 18.8
50.6 22.8
50.2 22.9
57.8 26.5
51.5 24.6
61.0 28.7
66.1 31.4
53.5 23.9
60.8 26.9
68.1 31.3
Active on
Power On
Units
–
Code
numer
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
7–13