8 horsepower 26" dual stage 120v. electric start (31 pages)
Summary of Contents for Craftsman 536.9183
Page 1
MODEL 536.918300 CAUTION: Read INSTRUCTIONS carefully SEARS, ROEBUCK • Assembly • Operating e Maintenance • Repair Parts CO., Chicago, Illinois 60684 U.S.A.
Page 2
FULL ONE YEAR WARRANTY If this Snow Thrower fails to perform properly due to a defect in material or workmanship within one year from the date of purchase, Sears wilt repair it, free of charge. WARRANTY SERVICE IS AVAILABLE SERVICE CENTER THROUGHOUT THE UNITED STATES.
Page 3
Itis observed to prevent the possibility imperative in operating and handling your Snow Thrower precautions before you assemble or use your new Snow Thrower. TRAINING 1. Wear safety glasses or eye shields when assmbling or operating snow thrower. 2. Read the Owner's Manual carefully. Be thoroughly familiar with the controls and the proper use of the...
Page 4
CONTENTS OF SHIPPING 1 - 24 inch Snow Thrower (completely handles, controls and headlight), 1 - Can of Engine 1 - Upper Chute Control 1 - Left Hand Handle Assembly 1 - Right Hand Handle Assembly (with I - Control Pane_ Assembly 1 - Bag of Assembly Parts...
Page 5
cable is loose and sags when lever down to last notch. To adjust cable: Loosen bottom nut on power and tighten top nut until lever will reach B. Loosen top nut and tighten looseness from cable when notch. 5_ Attach throttte control lever...
Page 6
Safety Mask standard safety SEARS Retail Familiarize yourself Operational OPERATING Operating controls follows: • Power Clutch forward drive control lever is in the appropriate the operator's desired...
Page 7
@ Chute Control Rod - Used to change discharge. Turn handle counterclockwise to left. Turn handle clockwise to turn chute snow can be discharged to one side by changing direction when changing direction @ Choke Lever - Set choke lever to FULL CHOKE to start engine.
Page 8
7. Check oil level in gear case by removing (figure 10). Oil should be visible in hole. If not, insert a funnel that an adjustable neck and add SEARS equivalent) engine until it starts Replace plug and tighten securely.
Page 9
3. Check b eltguides ( figure 12)forproper clearances as follows: I MPORTANT: Never l oosen bothbeltguides at same time.Adjust o nebeltguide, other guide. Ptace impeller!auger lever B. Have someone hold power engaged position. C. Adjust left belt guide, if necessary, between guide and be}t of not more than 1/16...
Page 10
C. Reclamp by moving lever from both directions gear). Never attempt LEVER CARBURETOR HIGH SPEED and IDLE ADJUST factory and re-adjustment think nearest SEARS equipment adjustments. Never tamper set for proper above factory If you think adjusting, Center experience Changing warranty.
Page 11
B° Remove C. Tip unit D. Replace 2. Check LEFT AUGER removing should be visible AUGER GEAR CASE and add SEARS oil level AUGER --11-- the parts of the broken bolt. the hole in the auger with the hole new shear bolt.
Page 12
Lubrication. the snow thrower in a protected area and cover protection. checkup tuneup SEARS is a good of insuring that your provide maximum performance for the stops several If unit is enter...
Page 13
{or equivalent) as required. Check every 5 hours and before each use. Add Sears S.A.E. 30W oil {or equivafent) as required. Check before each use. Remove chute and coat with clinging type grease such as lubriplate once each season.
Page 27
TROUBLE LOOK Difficult starting, Defective spark I_locked fue'i 'iine or Engine runs erratic empty gas tank "-Engine stalls; Unit running Obstruction Loss of power; impeller housing Engine runs erratic Water in fuel Excessive vibration Loose parts; Damaged impeller Drive belt loose or Unit fails to propel...
Page 28
"Your Sears merchandise has added value when you consider that Sears has service units nationwide trained technicians . . . professional technicians specifically trained on Sears products, having the parts, tools and equip- ment to insure that we meet our pledge to you.., what we sell." CO., Chicago,...