Advertisement

BURNERS
MODEL F10
INSTALLATION
MANUAL
RIELLO 40
SERIES
OIL BURNERS
RETROFIT APPLICATIONS
ONLY
NON-RETROFIT
APPLICATIONS
If this burner
is being
installed
in a packaged
unit (ie. burner
comes
with
a
boiler
or furnace),
follow
the installation
and set-up
instructions
supplied
with
the heating
unit, as settings
may differ
from those
shown
in this manual.
F10-2000-02
2902554-1

Advertisement

Table of Contents
loading

Summary of Contents for Riello Riello F10

  • Page 1 BURNERS MODEL F10 INSTALLATION MANUAL RIELLO 40 SERIES OIL BURNERS RETROFIT APPLICATIONS ONLY NON-RETROFIT APPLICATIONS If this burner is being installed in a packaged unit (ie. burner comes with boiler or furnace), follow the installation and set-up instructions supplied with...
  • Page 2: Parts List

    TECHNICAL DATA ... Dimensions Specifications OIL BURNER COMPONENTS F10 Burner Components Serial Number INITIAL SET-UP ASSEMBLY OF AIR TUBE TO BURNER MOUNTING THE BURNER Method 1- Universal Method 2- Semi-flange Method 3- Pedestal ELECTRICAL CONNECTIONS APPLICATION FIELD WIRING NOZZLE PLACEMENT...
  • Page 3: Specifications

    DIMENSIONS Inches 10 5/16 10 inch long (254 mm) tubes SPECIFICATIONS FUEL: No. 2 Fuel FIRING RATE: 1.45 to 2.95 EFFECTIVE OUTPUT: 203,000 51,160 VOLTAGE (Single Phase): ABSORBED ELECTRICAL MOTOR (rated): 3250rpm CAPACITOR: 12.5Microfarads260V PUMP PRESSURE: 130 to 200PSI PRIMARY CONTROL: IGNITION TRANSFORMER:...
  • Page 4: Initial Setup

    00025, is identified A = BI-week of manufacture; of 1 for each burner produced ( 00025 _ Sequence] I burner product code I parts list (inside cover) securing it.
  • Page 5 AIR TUBE by loosening out of the AIR TUBE, (4) of the BURNER CHASSIS. PLATE (5) with the two holes the BOLTS (3) were DRAWER ASSEMBLY depending...
  • Page 6 (A), include GASKET and FLANGE, if used. D) The burner may now be attached heating unit by inserting through the BURNER ACCESS and into the appliance, making BOLTS (1)line up with the two HOLES in the ADJUSTABLE COLLAR.
  • Page 7 CHAMBER AREA, AS EXCESSIVE THE END CONE. ELECTRICAL It is advisable to leave the control connections to the burner. 1) Wire access hole (Use BX electrical connector) 2) Earth ground conductor (GREEN WIRE) 3) Hot conductor terminal (BLACK WIRE) 4) Neutral conductor...
  • Page 8: Field Wiring

    The burner may be controlled using either a DIRECT LINE VOLTAGE control circuit (120V AC 60 cycle) OR a LOW VOLTAGE control (24V AC 60 cycle) using a R8038A Honeywell switching relay or equivalent. Using the appropriate diagram below, make electrical connections to burner. All wiring must be done in accordance with existing electrical codes, both national and local.
  • Page 9 Burner Set-up chart 12 to select proper pump pressure to obtain input from the burner. B) Remove NOZZLE (2) from the DRAWER ASSEMBLY loosening the SCREW (1). C) Insert the proper NOZZLE NOZZLE...
  • Page 10: Oil Line Connections

    Note: Pump pressure must attached PRESSURE CONNECTORS (5) are supplied two-pipe system. Also supplied oil lines to burner pipe connectors. design. Direct connection ELECTRODE SETTING 5/32" or 4 mm 5/32" to 13/64" TURBULATOR SETTING number chart, NUT (1).
  • Page 11: Single Line System

    SINGLE LINE (GRAVITY A) The burner is shipped configured the oil pump are required for use in single line applications. NOTE: If the pump cover (1) is removed for any reason, be sure the O-ring (2), is properly seated in the pump cover (1) before re-attaching the pump cover to the pump housing.
  • Page 12: Two Line (Lift System)

    I WARNING: The height "P" in Pipe Length charts on page 9 and 10 should not I WARNING: The vacuum should placed in the fuel line between the fuel tank and the burner pump. I IMPORTANT: An external, 2 LINE (LIFT)
  • Page 13: Pump Purge

    8) Reinstall the air tube cover 9) The burner can now be started WARNING: Omitting steps 2 and 3 will bustion chamber creating B) TWO LINE (LIFT SYSTEM)
  • Page 14: Burner Set-Up Chart

    Use in- settings reading gas, smoke, cover is put burner cover making the final readings, BURNER SET-UP CHART PUMP SIZE PRESSURE 10.4 DelavanW-B, DanfossS-B, is suggested, however, is unstable at light-off F10- PLATE by adjustment...
  • Page 15 COMBUSTION CHAMBER Follow instructions application according to the appropriate installation codes (eg. CSA B139 or NFPA #31 ). NON-RETROFIT APPLICATIONS If this burner is being installed furnace), follow the installation as settings will differ from furnished by the boiler/furnace in a packaged unit (ie.
  • Page 16 OPTIONAL...
  • Page 17: Spare Parts List

    SPARE PARTS LIST CODE DESCRIPTION 3007234 Burner Back Cover 3006992 Pipe connector - Supply 3006571 3/8" NPT/Metric 3006993 Pipe connector- 3005847 1/4" NPT/Metric 3007077 Crushable Metal Washer 3007568 Bleeder 3007028 O-Ring - Pump Pressure 3007202 Regulator Screw 3007162 O-Ring - Pump Cover...
  • Page 18: Air For Combustion

    CONNECTIONS All electrical connections local codes. The system should be grounded. CONTROL BURNER Check out the burner and explain the Owner's Instruction sheet with the homeowner. FIRE EXTINGUISHER If required by local codes, install an approved fire extinguisher. FOR CANADA...
  • Page 19 The system placed close to the burner CONTROL BURNER OPERATION Check out the burner and explain the Owner's Instruction sheet with the homeowner. FIRE EXTINGUISHER If required by local codes, install an approved FOR USA PRECAUTIONS insufficient air for combustion.
  • Page 20 Riello Canada Inc. 2165 Meadowpine Boulevard Mississauga, Ontario L5N 6H6 Telephone :905-542-0303 Facsimile :905-542-1525 Toll Free :1-800-387-3898 TECHNICAL RIELLO NORTH AMERICA Riello Corporation 35 Pond Park Road Hingham, Massachusetts Telephone :781-749-8292 Facsimile :781-740-2069 Toll Free : (outside Massachusetts) HOT LINE (USA and CANADA) WEBSlTE: of America 02043...

This manual is also suitable for:

40 series

Table of Contents