ANSI A156.13 specification, making it the best choice for any building where security, safety, and design compatibility are the prime considerations. The L-Series lock uses one common mortise lock case for all trim. This allows excellent design flexibility in trim combinations such as knob by lever, lever by knob, as well as knob by knob or lever by lever.
(35mm) to 2 (64mm) Regular parts assembled to order. Over 2 (64mm) door ranges vary by function. N escutcheon available for 1 (44mm) doors standard. 2 (51mm) to 2 (60mm) Regular parts assembled to order. Specify door thickness if other than Case Size: 4 x 1 (113mm x 154mm x 25mm).
Steel case and parts corrosion protected Trim applied by threaded bushing No exposed screws Fusible link built into lockcase Standard Door Preparation See templates. Note: L-Series mortise locks meet all requirements for installation in doors and frames prepared in accordance with ANSI 115.1.
Mediterranean Designs & Finishes This product offering combines the beauty of Schlage’s Mediterranean levers with all the features and benefits of our L-Series heavy duty commercial mortise lock. Two designs, Asti and Merano, are offered in two finishes. The L escutcheon is also available in addition to the special roses shown below.
7/16" 11mm 8" 203mm 7/16" 11mm A-WROUGHT ROSE (54mm) Diameter Available for use on L-Series knob and lever designs. Order by letter designation corresponding to the design and diameter desired. B-WROUGHT ROSE (65mm) Diameter Available for use on L-Series knob and lever designs.
4 = With Deadbolt 0 = Dummy Trim without Lock Case 9 = Functions with Lock Case Lock Series * To order less Schlage logo specify lock “with K510-612 faceplate” . SFIC = Small Format (Best ® Style) Interchangeable Core...
Functions • ANSI A156.13, Series 1000 Mortise Locks—Non-Keyed SCHLAGE ANSI L9010 Passage Latch Latchbolt retracted by knob/lever from either side at all times. L9040 Bath/Bedroom Privacy Lock Latchbolt retracted by knob/lever from either side unless outside is locked by inside thumbturn. Turning inside knob/lever or closing door unlocks outside knob/lever.
Mortise Locks—Keyed SCHLAGE ANSI L9050 Office and Inner Entry Lock Latchbolt retracted by knob/lever from either side unless outside is made inoperative by key outside or by turning inside thumbturn. When outside is locked, latchbolt is retracted by key outside or by knob/lever inside.
* Caution: Double cylinder locks on residences and any door in any structure which is used for egress are a life safety hazard in times of emergency and their use is not recommended. Installation should be in accordance with...
OCCUPIED and all keys become inoperative except emergency keys. Turning inside knob/lever simultaneously retracts both deadbolt and latchbolt. Auxiliary latch deadlocks latchbolt when door is closed. Specify per L583-375. (Previously XL11-580) L9496 Privacy With “OCCUPIED” Indicator Knob/lever retracts latchbolt from either side.
* Caution: Double cylinder locks on residences and any door in any structure which is used for egress are a life safety hazard in times of emergency and their use is not recommended. Installation should be in accordance with existing codes only.
XL11-557. * Caution: Double cylinder locks on residences and any door in any structure which is used for egress are a life safety hazard in times of emergency and their use is not recommended. Installation should be in accordance with existing codes only.
Primus high security cylinders are available to add patented key control and varying degrees of geographical exclusivity to most Schlage 6-pin key systems, whether Everest or Classic keyways. In addition to a conventional pin tumbler mechanism, Primus cylinders incorporate a patented finger pin and sidebar design providing a “dual-locking”...
(cylinder with compression ring & spring) * Specify door hand for hotel function cylinders. ** Discard compression ring for Lockout cylinders with escutcheon trim. Finishes: 605, 606, 611, 612, 613, 625, 626, 629, and 630. Concealed shell cylinders available 606 and 626 only.
Available 606 and 626 finish only. Standard keyway: 6-pin Everest C123 for stock, C145 for new master key systems. To order Schlage L-Series mortise locks with full size IC cylinders, change suffix P to R; example: L9453R. To order interchangeable core locks less core, change suffix to J;...
Small Format Interchangeable Core (SFIC) Cylinders The L-Series lockset can be ordered to accept small format interchangeable cores (SFIC) compatible with Falcon, Arrow, Best, etc. and cams are easily changeable. Small Format Interchangeable Core Cylinders Design L & N Escutcheons...
Escutcheon Rose Trim Rose Trim — Trim Rose Escutcheon Rose — Escutcheon Rose Trim\ Rose Trim\ — S E R I E S L538-195 Compression Ring Door Thickness ˝ ˝ 2˝ Dimension Door Thickness ˝ ˝ 2˝ Dimension ˝ ˝...
Switch (Not Furnished) Typical Installation • Electrified L-Series locks contain a transistorized circuit which provides full voltage to the solenoid upon initial application of electrical power and at 5 to 10 second intervals. • Each lock should preferably have its own 24 volt transformer.
Standard Square Corner (32mm) Width ” Strikes All L-Series strikes are produced from brass, bronze or stainless steel material, finished to match lock trim, and are furnished complete with screws. Numbers for ordering separately or with locks are listed below.
S E R I E S Door Handing One of the revolutionary features of the L-Series mortise lock is that handing can be done by the distributor or installer quickly and easily without opening the lock case. This feature allows a Schlage distributor to order L-Series locks as stock and customize the handing to each order’s specification.
L9456R Note: Schlage order forms are available at no charge by contacting your Schlage Representative or Customer Service. * To specify complete design, combine the numeric knob or lever design with the alpha rose or escutcheon design. Example: 03L, 93A, 42B.