Table 1 Burner Specifi Cation; Table 2 Air Tube Combination (Atc) Codes - Beckett AF Manual

General Specifi cations
Table 1 – Burner Specifi cations
Capacity 'F' Head (AF & AFG)
(Note 1) Firing rate range: ..............0.40 – 3.00 GPH
Input: ....................... 56,000 – 420,000 Btu
'L1' Head (AFG Only)
Firing rate range: ..................0.40 - 1.10 GPH
Input: ..................... 56,000 – 154,000 Btu/h
'L2' Head (AFG Only)
Firing rate range: .................0.50 - 1.00 GPH
Input: ...................... 70,000 – 140,000 Btu/h
'V1' Head (AFG Only)
Firing rate range: .................0.75 - 2.75 GPH
Input: .................... 105,000 – 385,000 Btu/h
Certifi cations/ UL certifi ed to comply with ANSI/UL296 &
Approvals tested to CSA B140.0
Fuels U. S: No.1 or No.2 heating oil only
Canada: No. 1 stove oil or No. 2 furnace oil
Electrical Power supply: ............... 120 volts AC, 60 Hz,
Operating load: .......................5.8 Amps max
Motor: ............ 1/7 hp, 3450 rpm, NEMA 48M
Ignition: ... Continuous duty solid-state igniter
Fuel pump
Outlet pressure: ..................................Note 2
Air tube ATC code: ...................................See Table 2
Dimensions Height (maximum) ....................... 12.5 inches
(with cover) Width (maximum) .......................... 15 inches
Depth ......................................... 9.25 inches
Air tube diameter ....................... 4.00 inches
Note 1: Approval agency listed rating for these burners is 0.40 to
3.00 gph. However, the fi ring rate range is limited by the
specifi c air tube combination being used. Refer to Table 2.
Note 2. See appliance manufacturer's burner specifi cations for rec-
ommended pump discharge pressure.
Table 2 – Air Tube Combination (ATC) codes
Firing Head Static Ven-
Rate plate turi
(gph) size
(min- (inch-
max) es)
0.50-0.75 F0 3-3/8U None
0.75-1.25 F3 2-3/4U None
0.85-1.35 F4 2-3/4U None
0.85-1.65 F6 2-3/4U None
1.10-2.00 F12 2-3/4U None
1.65-2.50 F22 2-3/4U None
2.50-3.00 F31 None None
0.50-1.10 L1 3-3/8U 8hole
0.50-1.00 L2 2-3/4U 8hole
0.75-2.75 V1 2-3/4U 8hole
0.40-0.75 F0 3-1/2U None
Page 4
(ASTM D396)
only
single phase
frame PSC rotation CCW
when facing shaft end
4-1/2 5 5-3/8
AF44XR - AF53XR
AF44XN - AF53XN
AF44WH - AF53WH
AF44YB - AF53YB
AF44XO - AF53XO
AF44XP - AF53XP
AF44XS - AF53XS
- AFG50MB
AFG50MP
- AFG50MD
AF44WG - AF53WG
WARNING
!
Incorrect installation, adjustment,
and use of this burner could result
in severe personal injury, death, or
substantial property damage from
fi re, carbon monoxide poisoning, soot or explo-
sion.
Please read and understand the manual supplied with
this equipment. This equipment must be installed, adjust-
ed and put into operation only by a qualifi ed individual or
service agency that is:
Licensed or certifi ed to install and provide techni-
cal service to oil heating systems.
Experienced with all applicable codes, standards
and ordinances.
Responsible for the correct installation and com-
mission of this equipment.
Skilled in the adjustment of oil burners using com-
bustion test instruments.
The installation must strictly comply with all applicable
codes, authorities having jurisdiction and the latest revi-
sion of the National Fire Protection Association Standard
for the installation of Oil-burning Equipment, NFPA 31 (or
CSA B139 and B140 in Canada).
Regulation by these authorities take precedence over the
general instructions provided in this installation manual.
ATC Codes for usable air tube lengths
('A' in inches; See Figure 3.)
6-5/8 7
AF65XR - AF72XR
AF65XN - AF72XN
AF65WH - AF72WH
AF65YB - AF72YB
AF65XO - AF72XO
AF56XP - AF72XP
AF65XS - AF72XS
- - AFG70MB
- - AFG70MP
- - AFG70MD
AF65WG - AF72WG
Professional Service
Required
7-1/4 9 10-1/2
AF90XR AF104XR
AF90XN AF104XN
AF90WH AF104WH
AF90YB AF104YB
AF90XO AF104XO
AF90XP AF104XP
AF90XS AF104XS
- AFG90MB -
- AFG90MP -
- AFG90MD -
AF90WG AF104WG
RWB 6104 BAFG R02
13 16
AF130XR A160XR
AF130XN AF160XN
AF130WH AF160WH
AF130YB AF160YB
AF130XO AF160XO
AF130XP AF160XP
AF130XS AF160XS
- -
- -
- -
AF130WG A160WG