Samsung SyncMaster 171B, 171S, 181B, 171T, 171Q User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. SyncMaster 171B, 171S, 181B, 171T, 171Q
  6. User manual

Samsung SyncMaster 171B, 171S, 181B, 171T, 171Q User Manual

Samsung lcd monitor owner's manual
Hide thumbs Also See for SyncMaster 171B, 171S, 181B, 171T, 171Q:
Table of Contents

Advertisement

Quick Links

SyncMaster 171B/171S/181B/171T/171Q

Advertisement

Table of Contents
loading

Related Manuals for Samsung SyncMaster 171B, 171S, 181B, 171T, 171Q

Summary of Contents for Samsung SyncMaster 171B, 171S, 181B, 171T, 171Q

  • Page 1 SyncMaster 171B/171S/181B/171T/171Q...
  • Page 2 Index Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting Your Monitor Installing the Monitor Driver — Automatic — Manual Installing VESA compliant mounting User’s Manual On-Screen Display Troubleshooting Check List Q & A Self-Test Feature Check Specifications General Specifications...

  • Page 3: Safety Instructions

    Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Do not disassemble Do not touch User’s Manual Important to read and understand at all times Disconnect the plug from the outlet Grounding to prevent an electric shock...
  • Page 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. • Do not use a damaged or loose plug. • This may cause an electric shock or fire. •...
  • Page 5 Safety Instructions Power • Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. • Failure to do so may cause an electric shock or fire. • Do not connect too many extension cords or plugs to an outlet.
  • Page 6 Safety Instructions Installation • Do not cover the vents on the monitor cabinet. • Bad ventilation may cause a breakdown or fire. • Put your monitor in a location with low humidity and a minimum of dust. • An electric shock or fire could result inside the monitor. •...
  • Page 7 User’s Manual Safety Instructions Installation • Do not place the monitor face down. • The TFT-LCD surface may be damaged.
  • Page 8 Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. • Do not spray detergent directly on the monitor. • Use the recommended detergent with a smooth cloth. • If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.
  • Page 9 Safety Instructions Other • Do not remove cover(or back). No user serviceable parts inside. • This may cause an electric shock or a fire. • Refer servicing to qualified service personnel. • If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized deal- er or service.
  • Page 10 Safety Instructions Other • Do not try to move the monitor by pulling on the wire or the signal cable. • This may cause a breakdown, electric shock or a fire due to damage to the cable. • Do not move the monitor right or left by pulling only the wire or the signal cable.
  • Page 11 Introduction Unparking • Monitor and Stand • Pivot Stand and S/W CD (Option-SyncMaster 171B/181B) Please make sure the following items are included (Some models include a stand attached. ) with your monitor. If any items are missing, Please make sure the following items are contact your dealer.
  • Page 12 Introduction Unparking (SyncMaster 171T) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. General Monitor and Stand Pivot Stand and S/W CD(Option) (Some models include a stand attached. ) Please make sure the following items are For Multimedia model (Option) included with your monitor.
  • Page 13 Introduction Front : Use this button to auto adjustment direct access. 1. Auto button : Use this button to Exit the active menu or the OSD. 2. Exit button 3,4. Adjust buttons : These buttons allow you to highlight and adjust items in the menu. : Use this button to open the OSD and activate a highlighted menu item.
  • Page 14 Introduction (SyncMaster 171T) Front 1. Auto button 2. Exit button 3,4. Adjust buttons 5. Menu button 6. Power button 7. Power indicator Note: See PowerSaver functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
  • Page 15 Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port : Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal cable : Connect the end of the signal cable to your computer's video port. (video board, video card or graphics card) Note : See Connecting Your Monitor for further information regarding cable connections.
  • Page 16 Introduction (SyncMaster 171T) Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power on/off Switch 2. Power port 3. Multimedia Stand Power Port 4. DVI Port 5. Signal Port Note: See Connecting Your Monitor Connect the power cord for your monitor to the power port on the back of the monitor.

  • Page 17: Connecting Your Monitor

    Setup Connecting Your Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3.
  • Page 18 Setup Connecting Your Monitor Setup-General 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3.
  • Page 19 User’s Manual Setup (SyncMaster 171T) Connecting Your Monitor Setup-For Multimedia model (Option) 1. Connect the power cord for your monitor to the power port on the back of the monitor. 2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3.
  • Page 20 Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ http://www.samsungusa.com/monitor/ http://www.sec.co.kr/monitor/ http://www.samsungmonitor.com.cn/ Windows ME 1.
  • Page 21 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/ 6. Monitor driver installation is completed.
  • Page 22 Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ http://www.samsungusa.com/monitor/ http://www.sec.co.kr/monitor/ http://www.samsungmonitor.com.cn/ ®...
  • Page 23 User’s Manual Setup 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7.
  • Page 24 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/ 9. Click the "Close" button then click "OK" button continually.
  • Page 25 Setup 10. Monitor driver installation is completed. ® ® Microsoft Windows When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3.
  • Page 26 Setup ® ® Microsoft Windows 1. Click "Start" , "Setting" , "Control Panel". 2. Double click "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6.
  • Page 27 Setup ® ® Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.
  • Page 28 User’s Manual Setup Installing VESA compliant mounting Removing the base 1 Turn off your monitor and unplug its power cord. 2 Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3 Remove the four screws and then remove the Stand from the LCD monitor.

  • Page 29: Attaching A Base

    User’s Manual Setup Installing VESA compliant mounting Attaching a base NOTE : This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad. 1. Rear cover mounting pad 2. Mounting interface pad Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with the four screws that came with the arm-type base, wall mount hanger or other base.

  • Page 30: On-Screen Display

    On-Screen Display (SyncMaster 171B/171S/181B/171Q) Use this button to open the OSD and activate a highlighted menu item. Use these buttons to highlight and adjust items using the On Screen Display. These buttons are also direct access buttons for the brightness feature.
  • Page 31 On-Screen Display Menu How to adjust Brightness Adjust the Brightness. 1. Push the Menu ( ) button. 2. Push the Menu ( ) button to open the Brightness adjustment screen. 3. Use the + button to increase the brightness or - button to decrease the brightness.

  • Page 32: Image Lock

    On-Screen Display Menu Image Lock How to adjust Fine Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
  • Page 33 On-Screen Display Menu Position How to adjust H-Position Follow these instructions to change the horizontal position of the monitor's entire display. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Position screen is displayed.

  • Page 34: Geometry Reset

    On-Screen Display Menu Reset How to adjust Geometry Reset Geometry parameters are replaced with the factory default values. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Reset screen is displayed. 3. Push the Menu ( ) button twice to open the Geometry Reset adjustment screen.

  • Page 35: Color Temperature

    On-Screen Display Menu Color Temperature How to adjust Color Temperature Color temperature is a measure of the "warmth" of the image colors. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Color Temperature screen is displayed.

  • Page 36: Image Effect

    On-Screen Display Menu How to adjust Image Effect Image being displayed can be made softer or sharper. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Image Effect screen is displayed. 3. Push the Menu ( ) button to open the Image Effect adjustment screen.
  • Page 37 On-Screen Display Menu How to adjust Menu Halfton Change the opaqueness of the background of the OSD. 1. Push the Menu ( ) button. 2. Push the - button or + button until the Menu Halfton screen is displayed. 3. Push the Menu ( ) button to open the Menu Halfton selection screen.

  • Page 38: Menu Position(H-Position)

    On-Screen Display Menu Menu Position How to adjust Menu Position(H-Position) You can change the horizontal position where the OSD menu appears on your monitor. 1. Push the Menu ( ) button. 2. Push the - button or + button until the H-Menu Position screen is displayed.

  • Page 39: Menu Display Time

    On-Screen Display Menu How to adjust Menu Display Time The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off. 1.

  • Page 40: Auto Adjustment

    On-Screen Display Menu To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. How to adjust Auto Adjustment Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.
  • Page 41 On-Screen Display (SyncMaster 171T) Use this button to open the OSD and activate a highlighted menu item. Use these buttons to highlight and adjust items using the On Screen Display. These buttons are also direct access buttons for the brightness feature.

  • Page 42: On Screen Display

    On Screen Display Menu Brightness Adjust the Brightness. 1 Push the Menu ( ) button. 2 Push the Menu ( ) button to open the Brightness adjustment screen. 3 Use the + button to increase the brightness or - button to decrease the brightness.
  • Page 43 On Screen Display Menu Image Lock Fine Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
  • Page 44 On Screen Display Menu Position H-Position Follow these instructions to change the horizontal position of the monitor's entire display. 1 Push the Menu ( ) button. 2 Push the - button or + button until the Position screen is displayed. 3 Push the Menu ( ) button twice to open the H-Position adjust- ment screen.
  • Page 45 On Screen Display Menu Reset Geometry Reset Geometry parameters are replaced with the factory default values. 1 Push the Menu ( ) button. 2 Push the - button or + button until the Reset screen is displayed. 3 Push the Menu ( ) button twice to open the Geometry Reset ad- justment screen.
  • Page 46 On Screen Display Menu Color Temperature Color Temperature Color temperature is a measure of the "warmth"of the image colors. 1 Push the Menu ( ) button. 2 Push the - button or + button until the Color Temperature screen is displayed.
  • Page 47 On Screen Display Menu Image Size If your computer or video board supplies a signal rate and addressability lower than 1280 x 1024, this LCD Monitor provides a scaling processor that can expand the addressability up to 1280 x 1024. 1 Push the Menu ( ) button.
  • Page 48 On Screen Display Menu How to adjust Halftone Change the opaqueness of the background of the OSD. 1 Push the Menu ( ) button. 2 Push the - button or + button until the Halftone screen is displayed. 3 Push the Menu ( ) button to open the Halftone selection screen.
  • Page 49 On Screen Display Menu Menu Position(H-Position) You can change the horizontal position where the OSD menu appears on your monitor. 1 Push the Menu ( ) button. 2 Push the - button or + button until the Menu Position screen is displayed.

  • Page 50: How To Adjust

    On Screen Display Menu Menu Display Time The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off. 1 Push the Menu ( ) button.
  • Page 51 On Screen Display Menu Auto Adjustment Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. 1 Push the Auto button. Note:To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

  • Page 52: Troubleshooting

    Troubleshooting Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your General Symptom No images on the...

  • Page 53: Check List

    Troubleshooting Check List General The screen Have you changed the video card or the driver? suddenly has become unbalanced. Have you adjusted the resolution or frequency to the monitor? The screen can be unbalanced due to the cycle of the video card signals.
  • Page 54 Troubleshooting Check List For Multimedia model (SyncMaster 171T Option) Symptom Connect the stereo input jack of the monitor to the stereo There is no sound. output jack of the computer thoroughly by using the voice cable or adjust the volume. Turn the volume up to MAX.
  • Page 55 Troubleshooting Q&A Question How can I change the frequency? How can I adjust the resolution? How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used.

  • Page 56: Self-Test Feature Check

    Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3.

  • Page 57: Werning Messages

    Troubleshooting Self-Test Feature Check Werning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.

  • Page 58: Specifications

    Specifications General General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16.7M (True) Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite, SOG TTL level positive or negative Maximum Pixel Clock 135 MHz...

  • Page 59: Power Consumption

    Specifications General Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 444.0 X 208.4 X 457.0 mm / 5.4kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product.
  • Page 60 Specifications General General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16.7M (True) Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite, SOG TTL level positive or negative Maximum Pixel Clock 135 MHz...
  • Page 61 Specifications General Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 444.0 X 208.4 X 457.0 mm / 5.4kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product.
  • Page 62 Specifications General General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16.7M (True) Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite, SyncOnGreen TTL level positive or negative Maximum Pixel Clock 135 MHz...
  • Page 63 Specifications General Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 444.0 X 457.0 X 208.4 mm / 5.4kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product.
  • Page 64 Specifications General General Model Name LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16.7M (True) Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite, SOG TTL level positive or negative Maximum Pixel Clock 135 MHz...
  • Page 65 Specifications General Power Consumption 42W (Maximum) Dimensions (WxDxH) / Weight 457.3 X 208.4 X 465.5 mm / 6.8kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product.
  • Page 66 EPA/ENERGY 2000 Green, Blinking Less than 3W TAR ® compliant and ENERGY2000 compliant NERGY TAR ® Partner, SAMSUNG has determined that this product TAR ® guidelines for energy efficiency. User’s Manual Power Switch off Black Less than 1W Power Switch off...
  • Page 67 Specifications Preset Timing Modes (SyncMaster 171B) If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

  • Page 68: Preset Timing Modes

    Specifications Preset Timing Modes (SyncMaster 171S/ If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
  • Page 69 Specifications Preset Timing Modes (SyncMaster 181B) If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

  • Page 70: Horizontal Frequency

    User’s Manual Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user.
  • Page 71 20063 Cernusco s/Naviglio (MI) Servizio Clienti: 199.153.153 http://www.samsung-italia.com/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service >...
  • Page 72 Samsung Electronics AB Box 713 S-194 27 UPPLANDS VÄSBY SVERIGE Besöksadress : Johanneslundsvägen 4 Samsung support Sverige: 020-46 46 46 Samsung support Danmark : 8088-4646 Samsung support Norge: 8001-1800 Samsung support Finland: 0800-118001 Tel +46 8 590 966 00 Fax +46 8 590 966 50 http://www.samsung.se/...
  • Page 73 Information Terms • Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm •...
  • Page 74 Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA Tel) 949-975-7310...
  • Page 75 Information Regulatory IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les équipements produisant des interférences au Canada. •...

  • Page 76: What Does Labelling Involve

    User’s Manual Information Regulatory • TCO'95-Ecological requirements for personal computers (TCO applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.

  • Page 77: Environmental Requirements

    Information Regulatory What does labelling involve?(continue) TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +46 8 782 92 07...
  • Page 78 User’s Manual Information Regulatory • TCO'99-Ecological requirements for personal computers (TCO applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.

  • Page 79: Tco Development

    User’s Manual Information Regulatory TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
  • Page 80 Information Regulatory • Medical Requirement Classifications: In accordance with UL 2601-1/IEC 60601-1, the product is cssified as Continuous duty Class I equipment, which is not protected against ingress of liquids. The product is not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide. This equipment has been tested and found to comply with the limits for medical devices to the IEC 601-1-2:1994.

  • Page 81: Natural Color

    The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images.

  • Page 82: For Better Display

    Information For Better Display Adjust computer resolution and screen injection rate (refresh rate) in control panel of computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.
  • Page 83 Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

This manual is also suitable for:

Syncmaster 171tSyncmaster 151sSyncmaster 151bSyncmaster 171v

Table of Contents