Important Note; Checking Parts; Tools Needed - Ryobi BT3000 Operator's Manual

RULES FOR SAFE OPERATION (Continued)
7. DO NOT MAKE ADJUSTMENTS UNTIL CUTTER OR BLADE HAS COME TO A COMPLETE STOP AND TOOL HAS
BEEN DISCONNECTED FROM POWER SOURCE.
8. FEED WORKPIECE AGAINST ROTATION OF CUTTER.
9. DO NOT USE AWKWARD HAND POSITIONS.
10. KEEP FINGERS AWAY FROM REVOLVING CUTTER, USE FIXTURES WHEN NECESSARY.
11. WHENEVER POSSIBLE, ALWAYS USE DUST COVER FOR OVERHEAD GUARDING.
12. DO NOT REMOVE JAMMED CUTOFF PIECES UNTIL CUTTER OR BLADE HAS STOPPED AND TOOL HAS BEEN
DISCONNECTED FROM POWER SOURCE.
13. HOLD WORKPIECE FIRMLY AGAINST THE TABLE.
14. UNUSED SAW MAY CAUSE PERSONAL INJURY. DISCONNECT MOTOR CORD FROM THE RECEPTACLE ON
YOUR SAW AND PLUG ACCESSORY POWER CORD INTO THE RECEPTACLE. ALWAYS USE THE SAW'S
MASTER SWITCH TO TURN THE ACCESSORY "ON" AND "OFF".
INTRODUCTION
As mentioned previously, this kit gives you the capability of
mounting a router or jig saw on the accessory table of your
BT3000. A router mounted on the accessory table will pro-
vide expanded capabilities for making rabbets, grooves,
chamfers, dovetails, and mortise and tenon joints. A jig saw
mounted on the accessory table will provide expanded
capabilities for cutting curves, scrollwork, and intricate pat-
terns.
The circle cutting jig included in this kit enables you to easily
cut circular patterns in both large and small stock with either
a router or jig saw.
The additional versatility gained from use of this kit will turn
your BT3000 table saw into a remarkable woodshaping
center.

IMPORTANT NOTE

This router kit has been specifically designed for use with the
Ryobi Model RE600 Electronic Router Only. The hole
pattern on the mounting plate has not been drilled to
accommodate other routers on the market.
This jig saw kit is used to mount a jig saw on the accessory
table of your BT3000 table saw. Ryobi jig saws plus many
other brands can be mounted using the parts supplied in this
kit. Before operating the jig saw, make sure the front and rear
clamping brackets properly secure the jig saw base to the
mounting plate. Care must be taken to insure that the jig saw
blade does not come in contact with the throat plate, accessory
table, or any part of the assembly during operation. Visually
inspect all areas of moving parts prior to connecting the jig
saw to power supply.
UNPACKING
Your new router and jig saw mounting kit includes two
separate mounting plates, two guide fences with guide
blocks, a dust cover assembly, a throat plate, plus the
necessary brackets and connecting hardware required to
mount a Ryobi Model RE600 Electronic Router to the
accessory table of your BT3000 table saw. It also includes
connecting hardware required to mount Ryobi jig saws to the
accessory table of your BT3000 table saw .

CHECKING PARTS

Separate all parts from packing materials. Check your parts
with the parts list on page 3. Refer to Figure 1 if you are
unsure about the description of any part. If any parts are
missing, delay assembly of this kit until you have obtained
the missing part(s).
WARNING:
Attempting to assemble the Router and Jig Saw
Mounting kit or to use in any way without obtaining any
missing parts and installing them correctly, could result
in an accident resulting in possible serious injury.

TOOLS NEEDED

Tools needed for assembly of this kit are a phillips screw-
driver, two slotted screwdrivers, and an adjustable wrench.
Note: Adjustable wrench will be used to tighten threaded
post into the special 5/16 in. T-nut provided.
WARNING:
Unplug the power supply cord of your BT3000 from
electrical outlet before you begin mounting this kit. It
should remain disconnected until the mounting operation
is complete, all attachments are installed properly, and
they have been checked to make sure they are secure.
Failure to unplug your saw could result in accidental
starting causing possible serious personal injury.
Page 2