Ryobi AirGrip ELL1001 Operator's Manual

OPERATOR'S MANUAL
cOMPAcT LASER LEvEL wiTh
AiRgrip
™
ELL1001
Your laser level has been engineered and manufactured
to our high standards for dependability, ease of opera-
tion, and operator safety. When properly cared for, it will
give you years of rugged, trouble-free performance.
wARNiNG: To reduce the risk of injury, the
user must read and understand the operator's
manual before using this product.
Thank you for your purchase.
SAvE ThiS MANUAL FOR FUTURE REFERENcE
SAFETy RULES
 do not place the laser level in a position that
wARNiNG! may cause anyone to stare into the laser beam
intentionally or unintentionally. Serious eye injury
REAd ANd UNdERSTANd ALL iNSTRUc-
could result.
TiONS. Failure to follow all instructions listed
 do not operate the laser level around children
below, may result in electric shock, fire and/or
or allow children to operate the tool. Serious
serious personal injury.
eye injury could result.
 Always turn the laser level off when not in use.
Leaving the tool on increases the risk of someone
cAUTiON:
inadvertently staring into the laser beam.
Use of controls or adjustments or performance of
 do not operate the laser level in combustible
procedures other than those specified herein may
areas such as in the presence of flammable
result in hazardous radiation exposure.
liquids, gasses, or dust.
 Always ensure the laser beam is aimed at a
surface without reflective properties. Shiny
cAUTiON:
reflective materials are not suitable for laser use.
The use of an optical instrument with this product
 handle the laser level with care. Treat it as you
will increase eye hazard. would any other optical device such as a camera
or binoculars.
The laser guide radiation used in this laser level is Class
 Avoid exposing the laser level to shock,
IIIa with < 5mW and 650 nm wavelengths. These lasers
continuous vibration or extreme hot or cold
do not normally present an optical hazard although
temperatures. Damage to the tool and/or serious
staring at the beam may cause flash blindness.
injury to the user could result.
 Avoid direct eye exposure when using the laser
 Save these instructions. Refer to them frequently
and do not project the laser beam directly and use them to instruct others who may use this
into the eyes of others. Serious eye injury could
laser level. If you loan someone this laser level,
result.
loan them these instructions also.
 do not remove or deface any product labels.
Removing product labels increases the risk of
exposure to laser radiation.
FEATURES
PROdUcT SPEciFicATiONS
Recommended Use......................................................................................................................................Indoor
Length of Laser Line ..........................................................................................Up to 30 ft., Horizontal or Vertical
Laser ............................................................................................................................. Class IIIa, <5mW, 650 nm
Power Supply .................................................................................................................2 AAA, 1.5 Volt Batteries*
Battery Life ................................................... 2.5 Hours Continuous Use — included Alkaline Batteries (Vacuum)
1 Hour Continuous Use — included Alkaline Batteries (Laser)
Operating Temperature...................................................................................................................... 32˚F to 104˚F
Dimensions ............................................................................................................. 3-1/2 in. x 2-7/8 in. x 1-3/8 in.
Accuracy ......................................................................................................................................± 1/2 in. at 20 ft.
* Laser level performance is greatly enhanced when using premium-branded alkaline batteries.
KNOw yOUR LASER LEvEL
laSer
See Figure 1.
lenS
The safe use of this product requires an understanding
of the information on the tool and in this operator's
manual as well as a knowledge of the project you
are attempting. Before use of this product, familiarize
yourself with all operating features and safety rules.
AiRgrip ™ vAcUUM TEchNOLOGy
Your laser level uses a vacuum base that can adhere to
smooth surfaces. Using the vacuum seal prevents wall
damage caused by nails, pins, or adhesive tape.
MOUNTiNG Aid
The AIRgrip vacuum may be ineffective on some sur-
faces. Use the mounting aid to increase the number of
surfaces on which the AIRgrip vacuum can be used.
mOUnTing
ALWAYS BE AWARE of the location where
the laser light is emitted when using the
level. ALWAYS MAKE SURE that any
bystanders in the vicinity of use are made
aware of the dangers of looking directly
into the laser beam.
983000-972
7-26-07 (REV:03)
ASSEMbLy
PAcKiNG LiST
UNPAcKiNG
This product has been shipped completely assembled. Laser Level
If any parts are damaged or missing, please call
AAA Batteries (2)
1-800-525-2579 for assistance.
OPERATiON
iNSTALLiNG bATTERiES
See Figure 2.
 Depress the ridged area on the bottom of the bat-
tery cover and pull the cover off the laser level.
 Install batteries according to polarity indicators
(+ or –) inside the battery compartment.
 Place the lens cover back onto the laser level and
secure.
wARNiNG:
When turning on the laser level, always protect
the eyes of yourself and those around you. Never
point the laser beam at anyone's face, including
your own.
TURNiNG ON/OFF
See Figure 3.
The on/off switch is located on the side of the laser level.
Pushing the switch down will turn the laser level ON and
activate the vacuum pump; pushing the switch up will
turn the unit OFF. Always wait for at least 5 seconds
between stopping and restarting the laser level.
USiNG ThE AiRgrip vAcUUM
See Figures 3 - 4.
The laser level's vacuum grip technology allows attach-
ment to most smooth surfaces.
 Place the laser level on the surface you want it
secured to and push in slightly to seal.
 Continue to hold the laser level against the surface
while turning on the laser.
 Release the laser level slowly when you hear a
change in motor sound.
NOTE: To release the vacuum seal, turn the laser
level's power off. For fast release, press the protrusion
on the side of the unit opposite the power switch.
Pulling the laser level off the wall without releasing the
vacuum could damage the tool.
The laser will automatically shut off 15 minutes prior
to battery failure, but the motor will remain on. Press
the on/off switch to power down the unit and replace
the batteries.
OPERATiNG ThE LASER LEvEL
See Figure 4.
 Place the laser level in the area where you want
the laser line projected.
 Rotate the unit so that the laser lens points in the
direction in which you want the line projected.
 Position the mounting aid on the surface where
 When a vertical line or level horizontal line is
desired, level the tool by centering the bubble
inside the appropriate vial located on top of the
 Place the laser level against the mounting aid and
laser head.
 Turn on the laser.
 Continue to hold the laser level against the surface
USiNG ThE MOUNTiNG Aid
See Figure 4.
 Release the laser level slowly when you hear a
Using the mounting aid, you can use the laser level's
AIRgrip feature to position the unit on many non-smooth
surfaces, including brick, painted cinderblock, textured
wallpaper, and stucco walls.
levelS
NOTE: The AIRgrip feature cannot be used with stucco
or unpainted cinderblock.
MAiNTENANcE
 To clean the laser lens, if needed, use ONLy a
wARNiNG:
To avoid serious personal injury, always remove the
batteries from the tool when cleaning or perform-
 Check the batteries regularly to avoid deterioration.
ing any maintenance.
GENERAL MAiNTENANcE
 Do not disassemble the laser level. This could
aid  Before initial use, wipe AIRgrip vacuum base with
a damp cloth to remove any residue.
 Do not attempt to change any part of the laser
 Store the laser level indoors.
 Keep the laser level free of dust and liquids. Use
SERvicE
a damp cloth and mild soap to clean the outside
This laser level has no serviceable parts. If the unit
casing. Avoid using solvents when cleaning plastic
fails due to normal wear and tear within two years of
parts. Most plastics are susceptible to damage
purchase, return with original receipt for a replacement
from various types of commercial solvents and
unit at no charge.
may be damaged by their use.
Fig. 1
wARNiNG:
Do not at any time let brake fluids, gas-
oline, petroleum-based products, pen-
etrating oils, etc., come in contact with
plastic parts. Chemicals can damage, weaken, or
destroy plastic, which may result in serious per-
sonal injury.
Please visit our website at www.ryobitools.com to register this product.
Model No. ELL1001
Ryobi is a registered trademark of Ryobi Limited used under license.
®
Mounting Aid
Operator's Manual
ridged
area
BaTTerieS
BaTTery
COver
Fig. 2
On
OFF
liFT TO releaSe
SUCTiOn
Fig. 3
POrOUS
SUrFaCe
mOUnTing aid
Fig. 4
you want to use the laser level. Secure with pins
or tape (not provided).
push in slightly to engage the seal.
while turning the unit ON and unit is adhered to
surface.
change in motor sound.
cAUTiON:
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
soft cloth or cotton swab moistened with glass
cleaner.
Remove the batteries from the laser level if it is not
going to be used for an extended time.
cause exposure to hazardous laser radiation.
lens.
ONE wORLd TEchNOLOGiES, iNc.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-525-2579
www.ryobitools.com