Quoizel SNNL9009K Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: LED 16W
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Mounting
A Screw
x 3
Fixture Body
x 1
-
STEP 1 Drill Pilot Holes on Post
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16" pilot
holes for screws.
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 3 - Attach Fixture Body to Post
A. Coat the top 1" of the Post with Clear Silicone Caulk (not supplied)
and position the Post Fitter onto the Post. Be sure to seat it
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2015 QuoizelInc.
Assembly Instruction Sheet #IS-SNNL9009
For Styles SNNL9009K and SNNL9009PN
for product cleaning tips. Go to the
20-30 minutes
B
Figure 1
Post Fitter
Mounting Hole
Post
White wire
from fixture
Black wire
from fixture
Figure 2
Ground wire
from fixture
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
Care + Maintenance selection.
(Step 3 Continued)
completely, aligning the holes in
the Fitter with the 1/16" Pilot Holes
drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled
and ready to use. Enjoy!
HOW TO REPLACE GLASS PANELS
A. Unlock Allen Screws on
the Fixture Hood and
remove the Fixture
Hood from the Cage.
B. Separate Quick
Connector and then
unscrew Screws from
the Cage and remove
LED Module and Heat
Sink, the Glass Holder.
Replace Glass Panels
from the Cage and then
re-install the Glass
Holder, LED Module
and Heat Sink. Secure
with removed Lock
Screws.
C. Connect Quick
Connectors. Attach the
Fixture Hood back onto
the Cage and secure
with Allen Screws.
1of2
Post Fitter
Mounting Hole
Post
Figure 3
Allen Screw
Male Quick
Connector
Screw
LED Module
and Heat Sink
Glass
Panel
Figure 4
Fixture
Hood
Female Quick
Connector
Glass
Holder
Cage
July2015