Using The 3-Band Equalizer In Input Mix/Track Mix - Roland VXpanded VS-880 Owner's Manual

Chapter 1 Trying out the expanded functions
About "!!! Lack of EVENT !!" display
Ò!!! Lack of EVENT !!Ó will be appeared in the display in the
following cases, and you cannot continue the current opera-
tion.
¥ If you push [SCENE]+[REC] buttons to record
AutoMix data in realtime, when the remaining num-
ber of EVENT is less than 1000.
¥ If you try to UNDO or REDO when the remaining
number of Event is less than 200.
The smallest unit of memory used by the VS-880 to store
recorded results on disk are the events. A newly created
song provides approximately 12,000 events per song.
For each track, one recording pass uses two events.
Operations such as punch-in/out or track copy also use up
events. The number of events that are used up will fluctuate
in a complex way. For example, auto mix uses up five
events for each mark point.
When you do a lot of recording, editing (Track Copy, Track
Move) or record AutoMix of long period, please check the
remaining number of Events frequently. Procedure is as fol-
lows.
1. Press [SYSTEM] several times until "SYS System
PRM?" appears.
2. Press [YES].
3. Press PARAMETER [
RemainDsp=" appears.
4. Select "Event" with TIME/VALUE dial.
CONDITION MARKER#
INPUT TRACK
Remaining number of Events can be saved with the follow-
ing procedures. Please try the most appropriate one with
your situation.
• Execute Song Store (Owner's manual p.74)
Please Execute Song Store if in UNDO condition
([UNDO] indicator is lit.). Events served for REDO will be
released. But please note that you cannot cancel (REDO)
the last UNDO if you once execute STORE.
• Execute Song Optimize (Owner's manual p.113)
Please execute Song Optimize if you have done a lot of
Punch In recording. Events served for unnecessary audio
data will be released. But please note that you can only do
single level UNDO.
• Erace AutoMix data (Owner's manual p.19)
If you have recorded AutoMix data, erase unnecessary
data. Events served for unnecessary AutoMix data will be
released.
20
] several times until "SYS
TIME TIME
dB
0
4
1 1 2 2
24
48
AUX MASTER
Using the 3-band equalizer in
INPUT MIX/TRACK MIX
From the total of fourteen INPUT MIX/TRACK MIX chan-
nels, you can now use a 3-band equalizer on any eight
selected channels.
* If equalizer is turned on for more than 8 channels, it will
not be possible to use the 3-band equalizer. Please turn off
the equalizer switch for channels on which equalization is
not required.
Turning the equalizer on/off
1. Make sure that the mixer mode is INPUT MIX/TRACK
MIX.
2. Hold down [SHIFT], and press channel 3 [EQ Low(CH
EDIT)].
3. Press PARAMETER [
4. Press [CH EDIT] for the channels or tracks for which
you wish to turn the equalizer off.
CONDITION MARKER#
INPUT TRACK
5. Rotate the TIME/VALUE dial.
EQ Switch (equalizer switch)
If you wish to use the equalizer, set this ÒOn.Ó If not, set this
ÒOff.Ó When equalizer settings are being made, the equal-
ization curve will be shown graphically in the bar display. If
this is ÒOffÓ the equalizer-related parameters will not be
available.
CONDITION MARKER#
INPUT TRACK
].
TIME TIME
dB
0
4
1 1 2 2
24
48
AUX MASTER
TIME TIME
dB
0
4
1 1 2 2
24
48
AUX MASTER