Read this First This manual provides instructions on how to use the VS-700R I/O on its own and how to add on a second VS-700R I/O. For instructions on how to perform the installation, make the necessary settings, and operate the unit, please refer to...
Do not attempt to repair the unit, or replace parts within it (except when this manual provides specific instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” (separate leaflet).
Page 4
Excessive loads can cause the insulation on the cord to heat up and eventually melt through. • Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” (separate leaflet). 022a •...
Page 5
• Always turn the phantom power off when connecting any device other than condenser microphones that require phantom power. You risk causing damage if you mistakenly supply phantom power to dynamic microphones, audio playback devices, or other devices that don’t require such power. Be sure to check the specifications of any microphone you intend to use by referring to the manual that came with it.
IMPORTANT NOTES Power Supply • Do not connect this unit to the same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine, microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise.
Page 7
* MMP (Moore Microprocessor Portfolio) refers to a patent portfolio concerned with microprocessor architecture, which was developed by Technology Properties Limited (TPL). Roland has licensed this technology from the TPL Group. * All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
USING THE UNIT SAFELY...3 IMPORTANT NOTES ...6 Checking the Contents of the Package ...9 Using the VS-700R I/O in Standalone Mode ... 11 Connecting Two VS-700R I/O Units ... 12 Connecting the Power Cord... 14 Turning the Power On ... 15 Connecting Recording Equipment ...
VS-700 Getting Started This explains how to get set up when using the VS-700C console (sold separately) together with the VS-700R I/O unit (this product). It also explains points to be aware of when installing the VS-700 series, and information you should know when using the system.
Page 10
Checking the Contents of the Package USB Cable Use this cable to connect the VS-700R I/O unit to your computer’s USB connector. * Please use the included USB cable.
Changes to the Settings In order to use the VS-700R I/O in “Standalone mode,” you need to open the top cover (ARX slot), then set the SETTING dip switches to the positions shown below. Next, switch the unit's power off, then turn it back on again.
The Advantages of Connecting VS-700R I/O Units By connecting two VS-700R I/O units, you'll be able to take advantage of the audio input/output of the two units, have access to two synthesizers (Fantom VS), and be able to use two ARX expansion boards.
Page 13
Otherwise, the audio ports of the second unit won't be recognized. If the audio ports of the second VS-700R I/O unit are not displayed in SONAR, try reconnecting the USB cables of the two VS-700R I/O units to different connectors on your computer, then quit and restart SONAR.
Connecting the Power Cord • Connect the power cord. fig.VS-700-connect04-e.eps Power Cord VS-700C Rear Panel Power Cord VS-700R Rear Panel to Power Outlet to Power Outlet...
If the connections are correct, the VS-700R’s USB indicator will light. If the USB indicator of the VS-700R I/O unit isn’t lit If the USB indicator of the VS-700R isn’t lit, the driver has not been installed correctly. Refer to the “Troubleshooting” chapter in “Getting Started.”...
Connecting Synthesizers or Audio Equipment VS-700R Rear Panel If you want to connect equipment such as a synthesizer or effects processor, use audio cables to connect the output connectors of such devices to the VS-700R’s INPUT jacks (1, 2). Connecting a Guitar or Bass If you want to connect a guitar or bass directly, connect it to the AUX IN jack located on the front panel of the VS-700C console.
Connections to the Digital Connectors fig.VS-700-rec02-digi-e.eps Connecting a Digital Audio Source If you want to digitally connect a DAT or similar device, connect its output connector (e.g., DIGITAL OUT connector) to the VS-700R's DIGITAL IN connector. VS-700R Rear Panel If you're connecting an ADAT device, connect it to the ADAT connector.
Close the software you’re using. Switch off the power to the VS-700R I/O and the VS-700C console. Set the VS-700R I/O’s [SAMPLE RATE] knob to the desired sampling rate.
Page 19
Setting SONAR’s Sampling Rate * In SONAR, you cannot change the sampling rate of a project that contains audio data. Start up SONAR. If an "Audio Driver Error" is displayed during startup, click [Use Anyway]. Choose “Options|Audio” to display the “Audio Options” dialog box. On the “General”...
If you’re using SONAR, you can select the clock source parameters as described below. If you’re using software other than SONAR, use “VS-700R I/O Editor” which is included on the “SONAR V- STUDIO 700 CD-ROM.” From SONAR’s “Tools” menu, open “VS-700.”...
• When installing Expansion Board, remove only the specified screws. • Be careful that the screws you remove do not drop into the interior of the VS-700R. • Do not leave the bottom cover removed. After installation of the Expansion Board is complete, be sure to replace the cover.
Page 22
Before installing the Expansion Board, turn off the power of the VS-700R and all connected devices, and disconnect all cables, including the Power cable, from the VS-700R. From the VS-700R, remove only the screws shown in the following diagram, and detach the cover. VS-700R Top Panel fig.exp02.eps...
Page 23
Insert the board into the VS-700R’s non-latched board holders until you hear a click. fig.attach02.eps Connector of board Connector of the VS-700R Gently lower the board into place. fig.attach04.eps From above, press down on the board at the three locations indicated in the illustration until the latched board holders lock into place.
Page 24
Installing the ARX Expansion Board Removing an Expansion Board To remove an expansion board, reverse the process by which you inserted it. Unlatch the latched board holders. fig.attach08.eps Verify that the two latched board holders are unlocked, then gently pull up the board and disconnect the connector.
• Quand l’installation de la carte de circuits imprimes est terminee, reverifiez si tout est bien installe. • Toujours eteindre et debrancher le VS-700R avant de commencer l’installation de la carte. (ARX series). • N'installez que les cartes de circuits imprimes spécifiées (ARX series). Enlevez seulement les vis indiquées.
Page 26
Sur les modeles VS-700R, retirer uniquement les vis illustrees dans le schema ci-dessous et retirer le couvercle. fig.exp02.eps Orienter la carte de facon a ce qu’elle s’aligne avec la vente de le VS-700R, comme le montre l’illustration. fig.attach01f.eps Fente de le VS-700R Supports bloqués...
Page 27
Inserer la carte dans les supports non bloques jusqu’a ce qu’un clic se fasse entendre. fig.attach02f.eps Connecteur de la carte Connecteur de le VS-700R Abaisser la carte delicatement. fig.attach04.eps Appuyer sur la carte aux trois points indiques sur l’illustration jusqu’a ce que les supports se bloquent en place.
Page 28
Installation de la carte d’expansion Retrait d’une carte d’expansion Pour retirer une carte d’expansion, suivre le processus inverse du processus d’insertion. Suivre les instructions donnees dans le guide d’utilisation de le VS-700R pour degager la fente ou la carte d’expansion a ete installee. fig.attach08.eps Debloquer les supports de carte.
Attaching the Rackmount Brackets If you want to install the VS-700R I/O in a 19” rack, attach the included rackmount brackets. Disconnect all connection cables from the VS-700R, including the power cord. As shown in the illustration below, remove three screws each from the left and right sides of the VS-700R.
Page 31
DECLARATION OF CONFORMITY Compliance Information Statement Model Name : VS-700R Type of Equipment : USB Audio Interface Responsible Party : Cakewalk, Inc. Address : 268 Summer Street Boston, MA 02210 USA Telephone : (617) 423-9004 This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.