Gigabyte R270-T60 Quick Installation Manual

R270-T60/R270-T61 Quick Installation Guide/R270-T60/R270-T61 速安装说明
41 43 44 45 1 2 3
40
39
52
42
38
37
46 47 48 51
36
35
34 49
11
13
50
12
28 23 19
29 24 20
30 25 21
31 27 26 22 18
33
32
System Cover/ 机箱盖
R270-T60
1
5
3 3
1
1
2 2
3
4 4
CAUTION!
Before you remove or install the system cover:
Make sure the system is not turned on or connected to AC power.
注意！
在卸下或安装系统机盖之前，请注意下列事项：
确保系统未开启且未连接到交流电源。
Fan Duct/ 风扇散热片
R270-T60
3
1
4 4
2
CAUTION!
To remove fan duct, follow the instruction:
1. CPU0: Remove the secruing screw, lift system fan slightly, then remove the fan duct.
2. CPU1: Remove the secruing screws of supporting bracket, lift system fan slightly,
then remove the fan duct.
注意！
1. CPU0: 移除导风罩上的螺丝并将风扇轻轻往上拉即可移除导风罩。
2. CPU1: 移除铁片上的螺丝并移除铁片，将风扇轻轻往上拉即可移除导风罩。
Power Supply/ 电源
3
CAUTION!
Before you remove or install the power supplies:
Make sure the system is not turned on or connected to AC power.
注意！
在替换或安装电源前，请注意下列事项：
确保系统未开启且未连接到交流电源。
Hard Disk Drive and Back Plane Board/ 硬盘驱动器与硬盘驱动器底板
3
4
4
2
1
4
3
4
1
2
PCI Express Card/PCI Express 扩展卡
R270-T60
3
1
2
3
R270-T61
1
2
CAUTION!
Before you remove or install the PCI express card:
Make sure the system is not turned on or connected
to AC power.
注意！
在安装扩展卡前，请注意下列事项：
确保系统未开启且未连接到交流电源。
PN:25ME0-R27000-CLR
No. Code Description
4 5
1 SW_ID ID switch button w/LED
2 QSFP_3 QSFP LAN port #3 (left)
QSFP_2 QSFP LAN port #2 (middle)
QSFP_1 QSFP LAN port #1 (right)
6
3 SFP+_0_3 SFP+ connectors #0~#3
4 USB3_MLAN BMC Management LAN port (top) / USB 3.0 ports (bottom)
5 COM1_VGA Serial port (top)/VGA port(bottom)
6 PMBUS PMBus connector
7
7 ATX1 24 pin power cponnector
8 F_USB3 USB 3.0 header
8
9 P12V_AUX2 8 pin power connector (for secondary CPU)
9 10 P12V_AUX1 8 pin power connector (for primary CPU)
11 MINI_CN0 Mini-SAS connector#0 supports SATA3 6Gb/s
10
12 MINI_CN1 Mini-SAS connector#1 supports SATA3 6Gb/s
13 BAT Battery socket
14 DIMM_P0_B0 Channel 2 slot 0 (for primary CPU)
15 DIMM_P0_B1 Channel 2 slot 1 (for primary CPU)
16 DIMM_P0_D0 Channel 4 slot 0 (for primary CPU)
14
17 DIMM_P0_D1 Channel 4 slot 1 (for primary CPU)
15
18 CPU0 Cavium ThunderX CN88xx ARMv8 SoC processor (Primary CPU)
19 DIMM_P0_C1 Channel 3 slot 1 (for primary CPU)
16
20 DIMM_P0_C0 Channel 3 slot 0 (for primary CPU)
17
21 DIMM_P0_A1 Channel 1 slot 1 (for primary CPU)
22 DIMM_P0_A0 Channel 1 slot 0 (for primary CPU)
23 DIMM_P1_F0 Channel 2 slot 0 (for secondary CPU)
24 DIMM_P1_F1 Channel 2 slot 1 (for secondary CPU)
25 DIMM_P1_H0 Channel 4 slot 0 (for secondary CPU)
26 DIMM_P1_H1 Channel 4 slot 1 (for secondary CPU)
27 CPU1 Cavium ThunderX CN88xx ARMv8 SoC processor (Secondary CPU)
28 DIMM_P1_G1 Channel 3 slot 1 (for secondary CPU)
29 DIMM_P1_G0 Channel 3 slot 0 (for secondary CPU)
30 DIMM_P1_E1 Channel 1 slot 1 (for secondary CPU)
31 DIMM_P1_E0 Channel 1 slot 0 (for secondary CPU)
32 BP_1 HDD back plane board header
33 FP_1 Front panel header
34 MINI_CN4 Mini-SAS connector#4 supports SATA3 6Gb/s
35 MINI_CN5 Mini-SAS connector#5 supports SATA3 6Gb/s
36 MINI_CN6 Mini-SAS connector#6 supports SATA3 6Gb/s
37 MINI_CN7 Mini-SAS connector#7 supports SATA3 6Gb/s
R270-T61 R270-T60
1
5
7
6
1 2
1
3
4
3
1
No Description
1 HDD bays
2 System fan #1 (FAN1_A/FAN1_B)
3 System fan #2 (FAN2_A/FAN2_B)
4 System fan #3 (FAN3_A/FAN3_B)
5 System fan #4 (FAN4_A/FAN4_B)
6 Memory slots
7 CPU heat sink
8 PCIe riser slots
9 Power supply cage
CAUTION!
R270-T61
To connect system fan connector, follow the instruction:
 Blue/Red cable connect to odd numbered connector.
3
White/Amber cable connect to even numbered connector.

1
2
1
CAUTION!
Remove fan duct before installing the CPU heat sinks.
R270-T60
2
1
CAUTION!
Before you remove or install the system fan:
 Make sure the system is not turned on or connected to the AC power.
 Disconnect all necessary cable connections. Failure to observe these warnings could result in
personal injury or damage to the equipment.
注意！
确保系统未开机且未连接到交流电源。
断开所有必要的线缆连接。若不遵循这些警告，可能造成人员伤害或设备损坏。
R270-T60 HDD Backplane Board Components
20 19 18 17 16
10 4
7
23 22
11 8 5
12 9 6
No Description No Description No
1 HDD#0 8 HDD#7 15
2 HDD#1 9 HDD#8 16
3 HDD#2 10 HDD#9 17
4 HDD#3 11 HDD#10 18
5 HDD#4 12 HDD#11 19
6 HDD#5 13 Fan connector#1_A 20
7 HDD#6 14 Fan connector#1_B 21
R270-T61 HDD Backplane Board Components
24 23 22 21 20 19 18 17 16 15 14 13 12 11
10 9
36
37
38 35
30 29
28
32 31
No Description No Description No
1 HDD#0 14 HDD#13 27
2 HDD#1 15 HDD#14 28
3 HDD#2 16 HDD#15 29
4 HDD#3 17 HDD#16 30
5 HDD#4 18 HDD#17 31
6 HDD#5 19 HDD#18 32
7 HDD#6 20 HDD#19 33
8 HDD#7 21 HDD#20 34
9 HDD#8 22 HDD#21 35
10 HDD#9 23 HDD#22 36
11 HDD#10 24 HDD#23 37
12 HDD#11 25 Fan connector#1_A 38
13 HDD#12 26 Fan connector#1_B
Rail Kit/ 导轨
Release
Lock out
Release and detach the inner member from the slide
1
M6-NUT
M6X13
Bracket
3 Fix the outer member/bracket assembly to the frame
Motherboard Components/ 主板组件
No.
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
System Components/ 系统组件
8
7 9
6
8
7
6
6
7
2
6
5
3
4
6
5
1
No Description
1 HDD bays
2 System fan #1 (FAN1_A/FAN1_B)
3 System fan #2 (FAN2_A/FAN2_B)
4 System fan #3 (FAN3_A/FAN3_B)
5 System fan #4 (FAN4_A/FAN4_B)
6 Memory slots
7 CPU heat sink
8 PCIe riser slots
9 Power supply cage
注意！
 蓝/红电缆连连接于单数风扇插座。
 白/橘电缆连连接于双数风扇插座。
Heat Sink/ 散热装置
R270-T60
注意！
安装散热装置前请先移除导风罩。
System Fan/ 系统风扇
15 14 13
1
21
2
3
Description No Description
Fan connector#2_A 22 SGPIO2
Fan connector#2_B 23 SGPIO3
Fan connector#3_A
Fan connector#3_B
Fan connector#4_A
Fan connector#4_A
SGPIO1
8 7 6 5 4 3 2
1
34 33
27
26 25
Description
Fan connector#2_A
Fan connector#2_B
Fan connector#3_A
Fan connector#3_B
Fan connector#4_A
Fan connector#4_B
SGPIO1
SGPIO2
SGPIO3
SGPIO4
SGPIO5
SGPIO6
Click
M4X6
A ach the unit to the inner member
2
Release
lock in
Insert the unit to complete the installa on
4
Code Description
S3_MASK S3 Power On Select Jumper
1-2 Close: Stop an initial power on when BMC
is not ready.
2-3 Close: Keep initial power on.
(Default setting)
BIOS_PWD Clearing Supervisor Password jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: Skip supervisor password.
BIOS_RCVR BIOS recovery jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: BIOS recovery mode.
COM2 Serial port cable connector
LAN Active LEDs LAN Active LEDs
LAN3_ACT LAN3 active LED (upper-left corner)
LAN4_ACT LAN4 active LED (bottom-left corner)
LAN5_ACT LAN5 active LED (upper-right corner)
LAN6_ACT LAN6 active LED (bottom-right corner)
LAN7_ACT LAN7 active LED (bottom-right corner)
CLR_CMOS Clear CMOS jumper
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data.
IPMB IPMB connector
BUZZER Buzzer
PCIE_5 PCI Express x8 slot
PCIE_4 PCI Express x8 slot
PCIE_3 PCI Express x8 slot
MINI_CN3 Mini-SAS connector#3 supports SATA3 6Gb/s
MINI_CN2 Mini-SAS connector#2 supports SATA3 6Gb/s
PCIE_2 PCI Express x16 slot
LED_BMC BMC firmware readiness LED
Front & Rear/ 系统前部与后部概览
System Front View
R270-T61
R270-T60
4
1
2
3
No. Description
9
1 Power button w/LED
2 Front panle LEDs and buttons
3 ID button w/LED
4 HDD bays
System Front View
R270-T61
4
1
2
3
No. Description
1 Power button w/LED
2 Front panle LEDs and buttons
3 ID button w/LED
4 HDD bays
Power button/LED:
R270-T61
State Description
Green On System is powered on
Off System is powered off
ID button/LED:
State
Description
System identifcation
Blue On
is active.
System identifcation
Off
is disabled.
Memory Population Configuration/ 安装内存
R270-T61
#DIMM per channel
Rank(s) 1 Rank
Data Width x4
Per DIMM Capacity (GB) 8,16
1600MTS

1866MTS

2133MTS

 DIMM must be populated starting from DIMM_P0_A0/DIMM_P0_B0 socket and must be installed in
matched pairs.
 One CPU only supports the population of 2/4 (1DPC)/8 (2DPC) in the same time.
 System will not boot normally with incorrect populated sequence.
 DIMM必须从DDR3_P0_A0//DIMM_P0_B0插槽开始按顺序安装。DIMM必须成对安装。
 只能支持一個CPU同時上2/4 (1DPC)/8(2DPC)數量的DIMM。
 若安装顺序有误，系统将无法正常开机。
Front Panel LED and Buttons/ 前面板 LED 说明
No. Name
3
1 Power Button and LED
1
4
5
2
2 ID Button and LED
6
3/4 LAN1/2 Active/Link LEDs
7
HDD Status LED
5
Green/Amber
6 System Status LED
Reset Button
7
编号 名称
1 电源按钮和LED
2
ID按钮LED
3/4
LAN1/LAN2活动LED
5 硬盘驱动器LED
6 系统状态LED
7
复位按钮
Front Panel Header/ 前面板接头
No. Pin Define No. Pin Define
24 23
1 Power LED+ 2 5V Standby
4 ID LED+
3 No Pin
6 ID LED-
5 Power LED-
8 System Front Board LED+
7 HDD LED+
9 HDD LED- 10 System Status LED-
12 LAN1 Active LED+
11 Power Button
14 LAN1 Link LED-
13 GND
16 SMBus Data
15 Reset Button+
18 SMBus Clock
17 GND
2 1
20 Case Open
19 ID Switch+
22 LAN2 Active LED
21 ID Switch-
24 LAN2 Link LED-
23 NMI Switch-
HDD Back Plane Board Header/
硬盘驱动器底板接头
No. Pin Define No. Pin Define
1 2 1 BP_SGP_CLK 2 No Connect
4 FAN_SGP_Gate
3 BP_SGP_GLD
5 BP_SGP_DOUT 6 GND
8 Reset
7 Key Pin
10 BP_LED_A_N
9 GND
12 GND
11 BP_LED_G_N
14 No Connect
13 BP_SGP_DIN
16 SMB_BP_DATA
15 GND
18 SMB_BP_CLK
17 GND
20 BMC_ACK
19 P_3V3_AUX
25 26
21 P_3V3_AUX 22 BMC_REQ
24 Key Pin
23 GND
26 GND
25 BP_PRESENSE
System Rear View
6
1 2 3 4 5 7 8 9
10
No Description
1 Power supply fan
2 Power supply module cord socket
3 VGA port
4 Serial port
5 KVM Server Management 10/100/1000 LAN port
6 USB 3.0 ports
7 SFP+ LAN ports
8 QSFP+ LAN ports
9 ID switch button w/LED
10 Low-profle half-length card
Speed LED Link/Activity 10/100/1000 LAN LED:
LED
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
Off 10Mbps data rate
Speed LED
SFP+ LAN LED:
State Description
Yellow On 1 Gbps data rate
Green On 10 Gbps data rate
Link/Activity LED
QSFP+ LAN LED:
SpeedLED Link/Activity
State Description
LED
Green On 40 Gbps data rate
Yellow On 10 Gbps data rate
Link/Activity LED:
State Description
Link between system
Green On
and network
Blink LAN is active
DDR4 UDIMM Configuration
#DIMM per channel 1 DIMM per channel 2 DIMM per channel
Rank(s) 1 Rank 2 Rank 1 Rank 2 Rank
Data Width x8,x16 x8,x16 x8,x16 x8,x16
Per DIMM Capacity (GB) 8 8,16 8 8,16
1600MTS
  
1866MTS
  
2133MTS
  
DDR4 RDIMM Configuration
1 DIMM per channel 2 DIMM per channel
2 Rank 1 Rank 2 Rank
x8 x4 x8 x4 x8 x4
4,8 16,32 8,16 8,16 4,8 16,32 8,16
     
     
  
Description
Color Status
Green Solid On System is powered on.
System is not powered on or in ACPI S5 state (power off).
N/A Off
System is in ACPI S4 state (hibernate mode).
Blue Solid On Press the button to activate system identifcation.
Green Solid On Link between system and network.
N/A Off No data transmission or receiving is occurring.
Green On HDD locate
Blink HDD access
Amber On HDD fault
Blink HDD rebuild
N/A Off No HDD access or no HDD fault
Green Solid On System is operating normally.
Critical condition, may indicates:
Power module failure
Solid On System fan failure
Power supply voltage issue
System temperature
Amber
Non-critical condition, may indicates:
Redundant power module failure
Blink
Temperature and voltage issue
Chassis intrusion
System is not ready, may indicates:
POST error
N/A N/A
NMI error
Processor or terminator missing
Press the button to reset the system.
颜色 状态 说明
绿色 恒亮 系统处于开机状态。
系统未开机或处于ACPIS5状态（关机状态）。
无亮灯 不亮
系统处于ACPI S4状态（休眠模式）。
恒亮
蓝色 按下按钮启动系统识别功能。
绿色 恒亮 系统和网络之间的链接
无亮灯 不亮 断开连接/待机
硬盘驱动器定位
亮
绿色
闪烁 硬盘驱动器访问
橙色
亮 硬盘驱动器故障
绿色/橙色
闪烁 硬盘重建
无亮灯 不亮 无硬盘驱动器访问
绿色 恒亮 系统正常运行。
严重情形，可能为下列状况：
电源模块故障
恒亮 系统风扇故障
电源电压问题
系统温度/电压问题
橙色
非严重情形，可能为下列状况：
冗余电源模块故障
闪烁
系统温度/电压问题
机箱侵入
系统未正常运行，可能为下列状况：
POST错误
无亮灯 不亮
NMI错误
处理器或终结器缺失
按此按钮启动系统。



x8

